Samsung SP R4232 Plasma Display User Manual
Have a look at the manual Samsung SP R4232 Plasma Display User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 Memorizing the Channels Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual). Selecting a broadcast source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system). 1 Press the MENU button. Press the ▲or ▼button to select “Channel”, then press the ENTER button. 2 Press the ▲or ▼button to select “Auto Program”, then press the ENTER button. 3 Press the ▲or ▼button to select the antenna connection, then press the ENTER button. Notes • Air : “Air” antenna signal. • Cable : “Cable” antenna signal. • Air + Cable : “Air” and “Cable” antenna signals. If the CableCARD is inserted into the “CableCARD” slot on the rear panel, “Cable” and “Air + Cable” are not available. Antenna : Air√Auto Program√Add / Delete √Favorite Channels√Name√Fine Tune√ †More ChannelTV MoveEnterReturn Antenna : Air√Auto Program√Add / Delete √Favorite Channels√Name√Fine Tune√ †More ChannelTV MoveEnterReturn Auto ProgramTV MoveEnterReturn Select the antennas to memorize Air Cable Air + Cable StartStartStart Auto ProgramTV MoveEnterReturn Select the antennas to memorize Air Cable Air + Cable StartStartStart 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 41
42 When selecting Cable TV system : Press the ▲or ▼button to select “Cable” or “Air + Cable”, then press the ENTER button. Press the ▲or ▼button to select “Digital Channel”, then press the ENTER button. Press the ▲or ▼button to select “STD”, “HRC”, or “IRC”, press the ENTER button. Press the ▲or ▼button to select “Analog Channel”, then press the ENTER button. Press the ▲or ▼button to select “STD”, “HRC”, or “IRC”, press the ENTER button. Press the ▲or ▼button to select “Start”, then press the ENTER button to memorize the channels. Note •STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory” on page 43. Auto ProgramTV MoveEnterReturn Select the cable system. Digital Channel : STD √Analog Channel : STD√Start Auto ProgramTV MoveEnterReturn Select the cable system. Digital Channel : STD √Analog Channel : STD√Start Auto ProgramTV MoveEnterReturn Select the cable system. Digital Channel :STD Analog Channel : STD Start STD HRC IRC Auto ProgramTV MoveEnterReturn Select the cable system. Digital Channel : STD Analog Channel : STD Start STD HRC IRC Auto Program EnterReturn Auto Program in Progress. CABLE Channel 67 Stop 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 42
43 Storing Channels in Memory 4 Press the ▲or ▼button to select the antennas to memorize. Press the ENTER button to select “Start”. 5 In Air, press the ENTER button to start the auto program. In Cable or Air + Cable, press the ENTER button to select the cable system. Press the ▲or ▼button to select “Digital Channel or Analog Channel”, then select the cable system. Press the ▲or ▼button to select “Start” and press the ENTER button to start the auto program. 6 The TV begins memorizing all available stations. Press the ENTER button at any time to interrupt the memorization process. Press the EXIT button to exit. Note •The TV must be connected to an antenna in order to receive digital TV signals. Even if a particular channel is deleted from the memory, you can always tune to that channel directly by using the number buttons on the remote control. Notes •All available DTV and analog channels are automatically stored in memory when channels are selected by directly accessing channels. •It takes approximately 3 to 10 minutes to memorize channels. Auto ProgramTV MoveEnterReturn Select the cable system. Digital Channel : STD √Analog Channel : STD√Start Auto Program EnterReturn Auto Program in Progress. AIR Channel 67 Stop Auto ProgramTV MoveEnterReturn Select the antennas to memorize Air Cable Air + Cable StartStartStart 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 43
44 1 Press the MENU button. Press the ▲or ▼button to select “Channel”, then press the ENTER button. 2 Press the ▲or ▼button to select “Add/Delete”, then press the ENTER button. 3 Repeatedly pressing the ENTER button will alternate between add channel and delete channel. Press the CH or CH button to switch to the appropriate channel, then repeat above. Press the EXIT button to exit. Adding and Erasing Channels To add channels that were not memorized (or to delete unwanted channels from memory): Antenna : Air√Auto Program√Add / Delete √Favorite Channels√Name√Fine Tune√†More ChannelTV MoveEnterReturn Antenna : Air√Auto Program√Add / Delete √Favorite Channels√Name√Fine Tune√†More ChannelTV MoveEnterReturn Add / Delete EnterReturn AIR 16 Not in memory Press ENTER to add the channel. Add Change Add / Delete EnterReturn AIR 16 In memory Press ENTER to delete the channel. Delete Change 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 44
45 Changing Channels Using the Channel Buttons Press the CH or CH button to change channels. When you press the CH or CH button, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels.) You will not see channels that were either erased or not memorized. Directly Accessing Channels Press the number buttons to go directly to a channel. For example, to select channel 27, press “2” then “7”. When you use the number buttons, you can directly select channels that were either erased or not memorized. To change to single-digit channels (0~9) faster, press “0” before the single digit. (For channel “4” press “0”, then “4”.) Notes•For quick channel change, press the number buttons and, then press ENTER button. •After the process of updating the channel information using CableCARD has been completed, only the number of channels on the channel list can be directly accessed. Using the PRE-CH button to select the previous channel Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. Adjusting the Volume Using the Volume Buttons Press the VOL or VOL button to increase or decrease the volume. Using Mute Using the MUTE Button At any time, you can temporarily cut off the sound using the MUTE button. 1Press the MUTE button and the sound cuts off. The word “MUTE” will appear in the lower-left corner of the screen. 2To turn mute off, press the MUTE button again, or simply press the VOL or VOL button. MUTE 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 45
46 Using the “-”Button The “-” button is used to select stations that broadcast both a digital and analog signal. For example, for Channel 7 -1 (digital), press “7”, then “-”, then “1”. For channel 7 -2 (analog), press “7”, then “-”, then “2”. Notes •HD indicates the TV is receiving a Digital High Definition signal. SD indicates the TV is receiving a Standard Definition signal. •For quick channel change, press the number buttons, then press the ENTER button. DTV CABLE 7 - 1 KYW-HD HD DTV CABLE 7 - 2 R SD Multi 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 46
47 Setting Up Your Remote Control This TVs remote control can operate almost any VCR, Cable box or DVD. After it has been set up properly, your remote control can operate in five different modes : TV, STB, VCR, CABLE, or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Notes : ●The remote control may not be compatible with all DVD Players, VCRs, or Cable boxes. ●The remote control can only operate Set-Top Boxes made by Samsung. Setting Up the Remote to Operate Your VCR, Cable box or DVD player 1 Turn off your VCR (or Cable box, DVD player). 2 Press the MODE button. The Mode is changed whenever MODE button is pressed. 3 Press the SET button on your TVs remote control. 4 Using the number buttons on your remote control, enter three digits of the VCR (or Cable box, DVD player) code listed on page 48 of this manual for your brand of VCR (or Cable box, DVD). Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your VCR (or Cable box, DVD) should turn on if your remote is set up correctly. If your VCR (or Cable box, DVD) does not turn on after setup, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR (or Cable box, DVD). If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008). Notes •When your remote control is in “VCR”, “CABLE”, or “DVD” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, and FF) still operate your VCR. •You do not need to program the remote for Samsung STBs as the codes are pre-programmed. 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 47
48 Remote Control Codes VCR Codes DVD Codes Cable Box Codes 2_BN68-00835C-00(36~49) 2/1/05 6:52 PM Page 48
49 Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as VCR, DVD, Set-Top Box, and the TV source (broadcast or cable). Setting the Signal Source 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ENTER button to select “Source List”. 3 Press the ▲or ▼button to select signal source, then press the ENTER button. 4 Press the MENU button to exit. Notes •When you connect equipment to the TV, you can choose between the following sets of jacks: AV, S-VIDEO, COMPONENT 1, COMPONENT 2, PC, or HDMI on the TV’s rear panel. •HDMI input can only be selected when the external device is turned on. ➤ ➤Quick way to access viewing an external signal source : Just press the “SOURCE” button on the remote control. Source List : TV√Edit Name√Anynet√ InputTV MoveEnterReturn TV AV : ----S-Video : ----Component 1 : ----Component 2 : ----PC : ----HDMI : ---- Source ListTV MoveEnterReturn TV AV : ----S-Video : ----Component 1 : ----Component 2 : ----PC : ----HDMI : ---- Source ListTV MoveEnterReturn 2_BN68-00835C-00(36~49) 2/5/05 9:16 AM Page 49
Assigning Names to External input mode 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ▲or ▼button to select “Edit Name”, then press the ENTER button. 3 Press the ENTER button. Press the ▲or ▼button to select external device, then press the ENTER button. • You can select the VCR, DVD, D-VHS, Cable STB, HD STB, Satellite STB, PVR STB, AV Receiver, DVD Receiver, GAME, Camcorder, DVD Combo, PC, VOD STB, or TV. • Set other signal sources (S-Video, Component 1, Component 2, PC, or HDMI) using the same method as listed above. 4 Press the MENU button to exit. 50 Source List : TV√Edit Name√Anynet√ InputTV MoveEnterReturn AV : ----√S-Video : ----√Component 1 : ----√Component 2 : ----√PC : ----√HDMI : ----√ Edit NameTV MoveEnterReturn AV :----S-Video : ----Component 1 : ----Component 2 : ----PC : ----HDMI : ---- Edit NameTV MoveEnterReturn † ----VCR DVD D-VHS Cable STB HD STB Satellite STB PVR STB 3_BN68-00835C-00(50~67) 2/1/05 6:54 PM Page 50