Samsung SP R4232 Plasma Display User Manual

							11
Checking Accessories
Power Cord 
(3903-000144)
Antenna Cable Anynet Cable 
(BN39-00518A)
Component Cables (RCA)HDMI/DVI cable  Owner’s Instructions
Remote Control (BN59-00462A) /
AAA Batteries
S-VIDEO Cable
HDMI Cable The following parts are sold separately and are available at most electronics stores.Once you have unpacked your TV, check to make sure that you have all the parts shown here.
If any piece is missing or broken, call your dealer. 
PC CablePC Audio CableOptical CableCoaxial Cable
BN68-00835C-00(002~035)  2/14/05  10:07 AM  Page 11 
						

							12
Rear Panel
ŒPOWER IN
Connect the supplied power cord.
´SERVICE ONLY
Connector for service only.
ˇHDMI/DVI IN
Connect to the HDMI jack of a device with 
HDMI output. These inputs can also be used 
as a DVI connection with separate analog 
audio inputs. An optional HDMI/DVI cable 
will be necessary to make this connection. 
When using the optional HDMI/DVI adapter, 
the DVI analog audio inputs on your TV allow 
you to receive left and right audio from your 
DVI device. (Not compatible with PC)
¨DVI AUDIO IN (L-AUDIO-R)
Connect to the DVI audio output jack of an 
external device.
ˆPC IN
Connect to the video output jack on your PC.
ØPC AUDIO IN
Connect to the audio output jack on your PC.
∏OPTICAL DIGITAL AUDIO OUT
Connect to a Digital Audio component.
”COAXIAL DIGITAL AUDIO OUT
Connect to a Digital Audio component.
’Anynet 
Please refer to the Anynet Owner’s
Instruction. This jack is for connecting to 
other Samsung Anynet-enabled devices.
˝COMPONENT IN 1, 2
Video (Y/PB/PR) and audio (L-AUDIO-R) 
component inputs.
ÔCableCARDTM
Insert the CableCARD into the slot.
ANT (75Ω)
75ΩCoaxial connector for Antenna/Cable 
Network.
ÒAV  IN (L-AUDIO-R)
Audio inputs for external devices, such as 
a camcorder or VCR.
ÚVIDEO
Video input for external devices, such as
a camcorder or VCR.
ÆS-VIDEO
Video input for external devices with an
S-Video output, such as a camcorder or VCR.
ıAUDIO OUT
Audio outputs for external devices.
BN68-00835C-00(002~035)  2/14/05  1:21 PM  Page 12 
						

							13
Remote Control Buttons
ŒPOWER button
Turns the TV on and off.
´GUIDE button
Press to display the on-screen Electronic Program Guide (EPG).
ˇANTENNA button
Press to select “Air” or “Cable”.
¨Number buttons
ˆ
-button
Press to select additional channels (digital and analog)
being broadcast by the same station. For example, to select channel
“54-3”, press “54”, then press “
-” and “3”.
ØMUTE button
Press to mute the TV sound.
∏VOL (Volume) buttons
Use it to adjust volume.
”Anynet button
Runs the Anynet view functions and sets up Anynet devices.
’MENU button
Displays the main on-screen menu.
˝ENTER button
Confirms a selection. 
ÔFAV.CH button
Press to switch to your favorite channels.
CH LIST button
Displays the channel list.
ÒMODE button
Selects a target device to be controlled by the Samsung remote control
(i.e., TV, STB, VCR, CABLE, or DVD).
ÚPRE-CH button
Tunes to the previous channel.
ÆSOURCE button
Press to display all of the available video sources (TV, AV, S-VIDEO, 
COMPONENT1, COMPONENT2, PC, and HDMI).
ıCH (Channel) buttons
Use it to switch channels.
˜INFO button
Press to display information on the TV screen.
¯EXIT button 
Press to exit the menu.
˘Up/Down/Left/Right buttons
Control the cursor in the menu.
Remote Control
BN68-00835C-00(002~035)  2/14/05  10:07 AM  Page 13 
						

							¿P.MODE buttonAdjust the TV picture by selecting one of the preset factory settings (or
select your personal, customized picture settings).
¸S.MODE buttonSelect Sound effect.
˛E.SAVING buttonPress to adjust screen brightness according to surrounding environment.
(Refer to page 115)
◊P.SIZE buttonSelect Picture size.
±DNIe buttonActivates DNIe (Digital Natural Image engine).
≠MTS buttonPress to choose stereo, mono or Separate Audio Program 
(SAP broadcast).
–SET buttonUsed during set up of this Samsung remote control, so that it will work
compatibly with other devices (VCR, Cable Box and DVD). 
—PIP buttonActivates picture in picture.
÷PIP control buttonsCH,: Displays the available channels in sequence. 
(These buttons change channels in the PIP window only.)
®CAPTION buttonControls the caption decoder.
∑VCR, DVD control buttonsControls VCR tape or DVD disc functions: Stop, Rewind, Play/Pause,
and Fast Forward.
µRESET button If your remote control is not functioning properly, take out the batteries
and press the reset button for about 2~3 seconds. 
Re-insert the batteries and try using the remote control again. 
14
Installing the Batteries in Your Remote Control
1Slide the back cover to
open the battery
compartment of the remote
control
.
3Slide the cover back into
place.2Install two AAA size
batteries. Make sure to
match the “+” and “-” ends
of the batteries with the
diagram inside the
compartment.
Remote Control Operation Range
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the left and right sides of the TV’s remote control receiver.
BN68-00835C-00(002~035)  2/14/05  10:07 AM  Page 14 
						

							15
Wall Installation Instructions
Refer to the correct installation guide according to your wall bracket.
1
Contact a technician for installing the wall bracket.
2
Samsung Electronics is not responsible for any damage to the product or injury to yourself
or others if you elect to perform the wall installation.
3
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Installation Notes
Parts (Wall attachment panel is sold separately. Check with your dealer.)
Only use the components and accessories shipped with the panel.
Plastic Hanger : 4Screw : 11
Screw : 4Anchor : 11 1Left : 1 Right : 1
Wall Bracket Hinge Accessories
BN68-00835C-00(002~035)  2/14/05  10:07 AM  Page 15 
						

							16
1 
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
2
Before drilling into the wall, check if the
length between the two locking holes at 
the back of the product is correct. If the 
length is too short or long, loosen all or 
some of the 4 screws on the wall 
bracket to adjust the length.
How to assemble the Wall Mount Bracket
3
Check the installation diagram and
mark the drill points on the wall. 
Use the 5.0 mm bit to drill holes deeper
than 35 mm. Fix each anchor in the 
corresponding hole. Match each of the 
brackets and hinge holes to the 
corresponding anchor holes and insert 
and tighten the 11 screws .
Captive Screw
Wall Bracket
Hinge (Right) There are two hinges
(left and right). Use the 
correct one. Hinge (Left)
Length between the
two locking holes
1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 16 
						

							17
1 
Remove the 4 screws on the back of the product.
2 
Insert the screw into the plastic hanger. (See the figure below)
Fixing the TV panel to the wall attachment panel bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
3
Tighten the 4 screws in step 2 (plastic
hanger + screw ) to the rear holes of 
the product.
4
Remove safety pin (#) and insert the 4
product holders into the corresponding 
bracket holes (!). Then place the 
product (@) so that it is firmly fixed to 
the bracket. Make sure to reinsert and 
tighten the safety pin (#) to securely 
hold the product to the bracket.
PDP
Wall Bracket Wall
• Mount the product on the wall bracket and make sure it is properly fixed to the left and 
right plastic hangers.
• Be careful when installing the product on the bracket as fingers can be caught in the holes.
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in 
place after installation.
1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 17 
						

							18
How to Adjust Mounting Angle
Note  Note : Adjust the bracket angle to -2° before installing it on the wall.
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it 
forward (direction of the arrow) to adjust the angle. 
(See the figure to the right)
3. You can adjust the bracket angle between 
-2° and 15°.
1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 18 
						

							19
How to assemble the Stand-Base
➤ ➤Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. 
Always store the TV upright.
1
Using the 4 screws for securing the stand pegs and the monitor, firmly attach the monitor
to the stand pegs. (The exterior of the set may be different than the picture.) 
Warning
Firmly secure the stand to
the TV before moving it, 
as the stand may fall and 
could cause serious injury.
1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 19 
						

							1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 20