Samsung SP R4232 Plasma Display User Manual

41
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable
channels. After the available channels are memorized, use the CH and CH buttons to scan
through the channels. This eliminates the need to change channels by entering the channel digits.
There are three steps for memorizing channels: selecting a broadcast source, memorizing the
channels (automatic) and adding and deleting channels (manual).
Selecting a broadcast source
Before your...

42
When selecting Cable TV system :
Press the ▲or ▼button to select “Cable” or “Air + Cable”, 
then press the ENTER button.
Press the ▲or ▼button to select “Digital Channel”, then 
press the ENTER button.
Press the ▲or ▼button to select “STD”, “HRC”, or “IRC”,
press the ENTER button.
Press the ▲or ▼button to select “Analog Channel”, then
press the ENTER button.
Press the ▲or ▼button to select “STD”, “HRC”, or “IRC”,
press the ENTER button.
Press the ▲or ▼button to select “Start”, then press the 
ENTER...

43
Storing Channels in Memory 
4
Press the ▲or ▼button to select the antennas to
memorize. Press the ENTER button to select “Start”.
5
In Air, press the ENTER button to start the auto program.
In Cable or Air + Cable, press the ENTER button to 
select the cable system.
Press the ▲or ▼button to select “Digital Channel or 
Analog Channel”, then select the cable system.
Press the ▲or ▼button to select “Start” and press 
the ENTER button to start the auto program.
6
The TV begins memorizing all available...

44
1
Press the MENU button.
Press the ▲or ▼button to select “Channel”, then
press the ENTER button.
2
Press the ▲or ▼button to select “Add/Delete”, then
press the ENTER button.
3
Repeatedly pressing the ENTER button will alternate
between add channel and delete channel.
Press the CH or CH button to switch to the 
appropriate channel, then repeat above.
Press the EXIT button to exit.
Adding and Erasing Channels
To add channels that were not memorized (or to delete unwanted channels from memory):
Antenna :...

45
Changing Channels
Using the Channel Buttons
Press the CH or CH button to change channels.
When you press the CH or CH button, the TV changes channels 
in sequence. You will see all the channels that the TV has memorized. 
(The TV must have memorized at least three channels.) 
You will not see channels that were either erased or not memorized.
Directly Accessing Channels
Press the number buttons to go directly to a channel. For example, to select
channel 27, press “2” then “7”.  
When you use the...

46
Using the “-”Button
The “-” button is used to select stations that broadcast both a digital and analog signal.
For example, for Channel 7
-1 (digital), press “7”, then “-”, 
then “1”.
For channel 7
-2 (analog), press “7”, then “-”, then “2”.
Notes 
•HD indicates the TV is receiving a Digital High Definition signal. 
SD indicates the TV is receiving a Standard Definition signal. 
•For quick channel change, press the number buttons, then press the ENTER button.
DTV CABLE
7 - 1
KYW-HD
HD
DTV CABLE
7 - 2...

47
Setting Up Your Remote Control
This TVs remote control can operate almost any VCR, Cable box or DVD. After it has been set up
properly, your remote control can operate in five different modes : TV, STB, VCR, CABLE, or DVD.
Pressing the corresponding button on the remote control allows you to switch between these modes,
and control whichever piece of equipment you choose.
Notes :
●The remote control may not be compatible with all DVD Players, VCRs, or Cable boxes.    
●The remote control can only...

48
Remote Control Codes
VCR Codes
DVD Codes Cable Box Codes
2_BN68-00835C-00(36~49)  2/1/05  6:52 PM  Page 48 

49
Viewing an External Signal Source
Use the remote control to switch between viewing signals from connected equipment, such as
VCR, DVD, Set-Top Box, and the TV source (broadcast or cable).
Setting the Signal Source
1
Press the MENU button. 
Press the ENTER button to select “Input”.
2
Press the ENTER button to select “Source List”.
3
Press the ▲or ▼button to select signal source, then
press the ENTER button.
4 
Press the MENU button to exit.
Notes
•When you connect equipment to the TV, you can choose...

Assigning Names to External input mode
1
Press the MENU button.
Press the ENTER button to select “Input”.
2
Press the ▲or ▼button to select “Edit Name”, then
press the ENTER button.
3
Press the ENTER button.
Press the ▲or ▼button to select external device, 
then press the ENTER button. 
•  You can select the VCR, DVD, D-VHS, Cable STB, 
HD STB, Satellite STB, PVR STB, AV Receiver, 
DVD Receiver, GAME, Camcorder, DVD Combo, 
PC, VOD STB, or TV. 
•  Set other signal sources (S-Video, Component 1,...