Samsung SP R4232 Plasma Display User Manual

11
Checking Accessories
Power Cord 
(3903-000144)
Antenna Cable Anynet Cable 
(BN39-00518A)
Component Cables (RCA)HDMI/DVI cable  Owner’s Instructions
Remote Control (BN59-00462A) /
AAA Batteries
S-VIDEO Cable
HDMI Cable The following parts are sold separately and are available at most electronics stores.Once you have unpacked your TV, check to make sure that you have all the parts shown here.
If any piece is missing or broken, call your dealer. 
PC CablePC Audio CableOptical CableCoaxial Cable...

12
Rear Panel
ŒPOWER IN
Connect the supplied power cord.
´SERVICE ONLY
Connector for service only.
ˇHDMI/DVI IN
Connect to the HDMI jack of a device with 
HDMI output. These inputs can also be used 
as a DVI connection with separate analog 
audio inputs. An optional HDMI/DVI cable 
will be necessary to make this connection. 
When using the optional HDMI/DVI adapter, 
the DVI analog audio inputs on your TV allow 
you to receive left and right audio from your 
DVI device. (Not compatible with PC)
¨DVI...

13
Remote Control Buttons
ŒPOWER button
Turns the TV on and off.
´GUIDE button
Press to display the on-screen Electronic Program Guide (EPG).
ˇANTENNA button
Press to select “Air” or “Cable”.
¨Number buttons
ˆ
-button
Press to select additional channels (digital and analog)
being broadcast by the same station. For example, to select channel
“54-3”, press “54”, then press “
-” and “3”.
ØMUTE button
Press to mute the TV sound.
∏VOL (Volume) buttons
Use it to adjust volume.
”Anynet button
Runs the Anynet...

¿P.MODE buttonAdjust the TV picture by selecting one of the preset factory settings (or
select your personal, customized picture settings).
¸S.MODE buttonSelect Sound effect.
˛E.SAVING buttonPress to adjust screen brightness according to surrounding environment.
(Refer to page 115)
◊P.SIZE buttonSelect Picture size.
±DNIe buttonActivates DNIe (Digital Natural Image engine).
≠MTS buttonPress to choose stereo, mono or Separate Audio Program 
(SAP broadcast).
–SET buttonUsed during set up of this Samsung...

15
Wall Installation Instructions
Refer to the correct installation guide according to your wall bracket.
1
Contact a technician for installing the wall bracket.
2
Samsung Electronics is not responsible for any damage to the product or injury to yourself
or others if you elect to perform the wall installation.
3
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Installation Notes
Parts (Wall attachment panel is sold separately. Check with...

16
1 
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
2
Before drilling into the wall, check if the
length between the two locking holes at 
the back of the product is correct. If the 
length is too short or long, loosen all or 
some of the 4 screws on the wall 
bracket to adjust the length.
How to assemble the Wall Mount Bracket
3
Check the installation diagram and
mark the drill points on the wall. 
Use the 5.0 mm bit to drill holes...

17
1 
Remove the 4 screws on the back of the product.
2 
Insert the screw into the plastic hanger. (See the figure below)
Fixing the TV panel to the wall attachment panel bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
3
Tighten the 4 screws in step 2 (plastic
hanger + screw ) to the rear holes of 
the product.
4
Remove safety pin (#) and insert the 4
product holders into the corresponding 
bracket holes (!). Then place...

18
How to Adjust Mounting Angle
Note  Note : Adjust the bracket angle to -2° before installing it on the wall.
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it 
forward (direction of the arrow) to adjust the angle. 
(See the figure to the right)
3. You can adjust the bracket angle between 
-2° and 15°.
1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 18 

19
How to assemble the Stand-Base
➤ ➤Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. 
Always store the TV upright.
1
Using the 4 screws for securing the stand pegs and the monitor, firmly attach the monitor
to the stand pegs. (The exterior of the set may be different than the picture.) 
Warning
Firmly secure the stand to
the TV before moving it, 
as the stand may fall and 
could cause serious injury.
1_BN68-00835C-00(02~35)  2/5/05  1:41 PM...

1_BN68-00835C-00(02~35)  2/5/05  1:41 PM  Page 20