Samsung SP P4251 Plasma Display User Manual

PLASMA DISPLAY PANEL
Connecting a PC and Operation
Connecting a PC ..........................................................................72
Adjusting the PC Screen................................................................76
Changing the Position of the Image ................................................77
Picture Quality Adjustment ............................................................78
Information ..................................................................................81...

Connecting a PC
Connection to a Macintosh computer may require an adapter.
72
Connecting a PC (15p D-SUB) to the PDP
Audio Cable
Audio Cable
PC Cable
DVI CablePower Plug
DVI jack(The actual configuration on
your PC may be different,
depending on the model.)
PDP
PC
or
Use a DVI-D
connection cable.
(sold separately)
Connect a PC cable between the PC Output jack on the PC and the RGB input jack on the PDP.
Connect a Audio cable between the Audio jack on the PC and the Audio input jacks (PC INPUT) on the...

73
Pin Configuration
D-Sub CableDVI-D Cable (Digital-Only Connector)
• 15Pin Signal Cable (based on protruded pin)
Setting up Your PDP (Plug and Play)
Our adoption of the new VESAPlug and Play solution eliminates complicated and time consuming
setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual
setup hassles and confusion. Your PC system can easily identify and configure itself for use with your
display. This monitor automatically tells the PC system its...

74
How to Set up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. However, the actual screens
on your PC will probably be different, depending upon your particular version of Windows and your
particular video card. But even if your actual screens look different, the same, basic set-up information
will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
On the windows screen, select in the following
sequence : Start...

75
Notes
Both screen position and size will vary, depending on the type of PC monitor and its resolution. 
The table below shows all of the display modes that are supported:
•The interlace mode is not supported.
•The PDP operates abnormally if a non-standard video format is selected.
•The table above conforms to IBM/VESA regulations and is based on using the Analog Input.
•The DVI Mode is supported same as above table.
Notes
•When this PDP is used as a PC display, 32-bit color is supported.
•Depending on...

Adjusting the PC Screen
76
Adjusting the R.G.B
Preset: 
•Press the SOURCE button to select “PC”.
1 
Press the MENU button. Press the ▲or ▼button to
select “Picture”, then press the ENTER button.
2
Press the ▲or ▼button to select “Color Control”,
then press the ENTER button. 
The “Color Control” is available only when 
the “Color Tone” is set to Custom and a PC is 
connected.     
3
Press the ▲or ▼button to select the item you want
to change, then press the ENTER button. 
Press the 
œ or√button to change...

77
Changing the Position of the Image
After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned.
Preset: 
•Press the SOURCE button to select “PC.”
1 
Press the MENU button. Press the ▲or ▼button to
select “Setup”, then press the ENTER button. 
2
Press the ▲or ▼button to select “PC”, then press
the ENTER button. 
3 
Press the ▲or ▼button to select “Position”, then
press the ENTER button.
4 
Adjust the position of screen by pressing the 
▲/ ▼/ œ /√button.
5 
Press the...

78
Picture Quality Adjustment
Picture Automatic Adjustment 
Preset: 
•Press the SOURCE button to select “PC”.
1 
Press the MENU button. Press the ▲or ▼button to
select “Setup”, then press the ENTER button.
2 
Press the ▲or ▼button to select “PC”, then press
the ENTER button.
3
Press the ▲or ▼button to select 
“Auto Adjustment”, then press the ENTER button.
The message “Auto Adjustment in progress.” 
appears on the screen and the picture adjustments 
are automatically activated.
4 
Press the MENU button...

79
Coarse Adjustment
Preset: 
•Press the SOURCE button to select “PC”.
1 
Press the MENU button. Press the ▲or ▼button to
select “Setup”, then press the ENTER button.
2 
Press the ▲or ▼button to select “PC”, then press
the ENTER button.
3 
Press the ▲or ▼button to select “Image Lock”,
then press the ENTER button.
4 
Press the ENTER button to select “Coarse”.
Remove picture noise (vertical stripes) on the screen
by pressing the 
œ or√button. (If Coarse is not set 
properly, vertical stripes will appear on...

80
Fine Tuning (Fine)
Preset: 
•Press the SOURCE button to select “PC”.
1 
Press the MENU button. Press the ▲or ▼button to
select “Setup”, then press the ENTER button.
2 
Press the ▲or ▼button to select “PC”, then press
the ENTER button.
3 
Press the ▲or ▼button to select “Image Lock”,
then press the ENTER button.
4 
Press the ▲or ▼button to select “Fine”, then press
the ENTER button.  
Remove picture noise on the screen by pressing 
the 
œ or√button. (If Fine is not set properly, noise
will appear on...