Samsung SF 650 User Manual

Introduction_ 20
Control panel overview
 1one-touch dial Stores frequently-dialed fax number (See S
toring a number for One-touch Dialing on 
page 39).
 2 Reduce/Enlarge Makes a copy smaller or larger than the original. 
 3
Delay Send Allows you to send a fax at a later time w
hen you will not be present (See Delaying a 
fax transmission on page 34).
 4 Multi Send Allows you to send a fax to multiple dest
inations (See Sending a fax to multiple 
destinations on page 34).
 5 Receive Mode Converts the fax...

Introduction_ 21
Understanding the Status LED
The color of the status LED indica tes the machines current status.
 
Samsung does not recommend using non-genuine Samsung toner  cartridge such as refilled or remanufactured. 
Samsung cannot guarantee non-genuine Samsung toner cartridges qual ity. Service or repair required as a result of 
using non-genuine Samsung toner cartridges will not be covered under the machine warranty. 
 Check the message on the display. Follow the instructions  in the message or...

Basic setup_ 22
2.Basic setup
You may want to set the machine’s  default settings. Refer to the next section if you would like to 
set or change values. This chapter gives you step-by-step instructions for setting up the machine.
This chapter includes:
• Setting up the hardware
• Changing the display language
• Setting the date and time
• Changing the clock mode
• Setting sounds
• Entering characters us in
 g the number keypad
• Using the save modes
• Setting the paper
  
Setting up the hardware
This...

Basic setup_ 23
8.Turn the machine on.
 
This equipment will be inoperable when mains power fails.
Changing the display language
To change the language that appears on the display, follow the steps below:
1.Press Menu until Machine Setup appears.
2.Press the left/right arrow until Language appears and press OK.
3.Press the left/right arrow to display the language you want.4.Press OK to save the selection.
5.Press Stop/Clear to return to ready mode.
Setting the date and time
When you set the time and...

Basic setup_ 24
1.Press (Fax) on the control panel.
2. Press
  On Hook Dial . A dial tone sounds from the speaker.
3. Press the
  left/right arrow until you hear the volume you want.
4. Press
  On Hook Dial  to save the change and return to ready mode.
To adjust the volume using the handset:
1. Pick u
p the handset. A dial tone sounds from the earpiece.
2.Press the  left/right arrow until you hear the volume you want.
3. Press
  OK to save the change and replace the handset.
 You can adjust the speaker...

Basic setup_ 25
Using the save modes
Using toner saving feature
Toner save mode allows your machine to use less toner on each page. Activating this mode extends the life of the toner 
cartridge beyond what one would experience in the normal mode, but it reduces print quality.
1.Press Menu until Machine Setup appears.
2.Press the left/right arrow until Toner Save appears and press OK.
3.Press the left/right arrow until On appears and press OK.4.Press Stop/Clear to return to ready mode.
 When PC-printing,...

Media and tray_ 26
3.Media and tray
This chapter provides information on how to load originals and print media into your machine.
This chapter includes:
•Preparing originals
• Loading originals
• Selecting print media
• Changing the tray size
• Loading paper in the tray
• Setting the paper size and type
• Using the output support
  
Preparing originals
•Do not load paper smaller than 148 x 148  mm (5.8 x 5.8 inches) or larger than 216 x 356  mm (8.5 x 14 inches).
• Do not att
 empt to load the following...

Media and tray_ 27
3.Load the original face down into the document feeder. Make sure that the bottom of the original stack matches the 
paper size marked on the document input tray.
4.Adjust the document width guides to the paper size.
Selecting print media
Always use print media that meet the  guidelines for use with your machine. 
Guidelines to select the print media
Print media that does not meet the guidelines outlined in  this user’s guide may cause the following problems:
• Poor pr int quality
•...

Media and tray_ 28
The amount of paper put into the tray may differ according  to media type used (See Print media specifications on 
page 71).
Media sizes supported in each mode
Changing the tray size
The tray is preset to Letter or A4 size, depending on your country. To change the size, you need to adjust the paper 
guides.
1. With one
  hand press and hold the guide lock, and with the other hand, hold the paper length guide and support guide 
together. Slide the paper length guide and support guide to...

Media and tray_ 29
4.Squeeze the paper width guides and slide them to the des ired paper size marked at the bottom of the tray.
 •Do not push the paper width guide too far causing the media to warp. 
• If you do not adjust the paper width guide, it may cause paper jams.
•Do not use a paper with more than 6 mm curl. 
Loading paper in the tray
Tray 1
1. Pull out the paper tray. And adjust the tray  size to the media size you are loading (See  Changing the tray size on 
page  28).
2. Flex o
r fan the edge...