Samsung SCX 4824FN User Manual

Maintenance_61
4.Slide the toner cartridge back into the machine.
5. Close the front cover. Make sure the cover is securely latched.
REPLACING THE TONER CARTRIDGE
• The status LED and the toner-relat ed message on the display indicates 
that the toner cartridge should be replaced.
• Incoming faxes are saved in memory.
At this stage, the toner  cartridge needs to be replaced. Check the type of 
toner cartridge for your machi ne. (See Ordering supplies and 
accessories on page 80.)
1. Turn the machine off,...

62 _Maintenance
8.Close the front cover. Make sure the  cover is securely latched, and then 
turn the machine on.
Clearing the Toner  Empty message
When the Toner Empty  message appears you can configure not to see this 
message again not to disturb you.
1. Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press the Scroll buttons until  Maintenance appears and press  OK.
3. Press the Scroll buttons until  CLR Empty Msg. appears and press  OK.
4. Select  On and...

Maintenance_63
5.Align the left end of the ADF roller wi th the slot and push the right end of 
the roller into the right slot. Rotate the bushing on the right end of the 
roller toward the document input tray.
6. Close the ADF cover.
MANAGING YOUR MACHINE FROM THE 
WEBSITE
If you have connected your machine to a network and set up TCP/IP 
network parameters correctly, you ca n manage the machine via Samsung’s 
SyncThru™ Web Service , an embedded web server. Use  SyncThru™ 
Web Service  to:
• View the...

64 _Troubleshooting
troubleshooting
This chapter gives helpful information fo r what to do if you encounter an error.
This chapter includes:
• Tips for avoiding paper jams
• Clearing document jams
• Clearing paper jams • Understanding display messages
• Solving other problems
TIPS FOR AVOIDING PAPER JAMS
By selecting the correct media type
s, most paper jams can be avoided. 
When a paper jam occurs, follow the steps outlined on page 64. 
• Follow the procedures on page 34. En sure that the adjustable...

Troubleshooting_65
Exit misfeed
1.Remove any remaining pages from the ADF.
2. Seize the misfeed paper, and remove the paper from the document 
output tray by carefully pulling it to the right using both hands.
3. Load the removed pages back into the ADF.
Roller misfeed
1.Open the scanner lid.
2. Seize the misfeed paper, and remove the paper from the feed area by 
carefully pulling it to the right using both hands.
3. Close the scanner lid. Then load the removed pages back into the ADF.
CLEARING PAPER...

66 _Troubleshooting
In the manual tray
When you print using the manual tray and the machine detects that there is 
either no paper or that the paper has been improperly loaded, follow the 
next steps to release the jammed paper.
1.Check if the paper is stuck in the feedi ng area, and if so, pull it out gently 
and slowly.
2. Load a paper into the  manual tray.
3. Open the front cover and close it. The machine will resume printing.
In the toner  cartridge area
If paper is jammed in the toner cartri dge...

Troubleshooting_67
2.Remove the jammed paper from the duplex unit.
If the paper does not come out with the duplex unit, remove the paper 
from the bottom of the machine.
If you cannot find the jammed paper , or if there is any resistance 
removing the paper, stop pulling and go to step 3.
3. Open the rear cover.
4. Pull the guide rear on each side down and remove the paper. Return the 
guide rear to its original position.
5. Close the rear cover. Prin ting automatically resumes.In the optional tray
If...

68 _Troubleshooting
UNDERSTANDING DI SPLAY MESSAGES
Messages appear on the control panel  display to indicate the machine’s 
status or errors. Refer to the tabl es below to understand the messages’ 
meaning and correct the problem if necessary. Messages and their 
meanings are listed in alphabetical order. 
• xxx indicates the media type.
• yyy indicates the tray.
• If the message is not in the table, cycle the power and try the  printing job again. If the problem persists, call for service.
• Some...

Troubleshooting_69
Memory Full  The memory is full. Delete unnecessary fax 
jobs and retransmit after 
more memory becomes 
available. Alternatively, 
split the transmission into 
more than one operation.
Not AssignedThe speed button or 
speed dial number 
you tried to use has 
no number assigned 
to it. Enter the number 
manually using the 
number keypad or store 
the number or address.
NonSAMSUNG 
Toner
T The toner cartridge is 
not a Samsung-
genuine cartridge.
Press 
OK to toggle 
the message to...

70 _Troubleshooting
SOLVING OTHER PROBLEMS
The following chart lists some conditions that may occur and the 
recommended solutions. Follow the suggested solu tions until the problem is 
corrected. If the problem persists, call for service.
Paper feeding 
Toner Exhausted T A toner cartridge has 
reached its estimated 
cartridge life. The 
printer stops printing.
Estimated 
cartridge life 
means the 
expected or 
estimated toner 
cartridge life, which 
indicates the average 
capacity of print-outs 
and is...