Samsung Rsh7znpn User Manual
Have a look at the manual Samsung Rsh7znpn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
setting up _11 01 SETTING UP LEVELLING THE REFRIGERATOR Now that the doors are back on the refrigerator, you will want to make sure the refrigerator is level so you can then make fi nal adjustments. If the refrigerator is not level, it will not be possible to get the doors perfectly even. The front of the refrigerator is also adjustable. When the Freezer door is lower than the fridge Insert a fl at-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to level the freezer. When the Freezer door is higher than the fridge Insert a fl at-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to level the fridge. Refer to the next section for the best way to make very minor adjustments to the doors. MAKING MINOR ADJUSTMENTS TO THE DOORS Remember, a level refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on levelling the refrigerator. In the process for adjusting both the doors is the same. Open the doors and adjust them, one at a time, as follows: Unscrew the 1. nut 1 from the lower hinge until it reaches the upper end of the bolt 2. When you release the nut 1, make sure that you use the Allen wrench provided 3 to loosen the bolt 2 in a counter-clockwise direction. You should then be able to unscrew the nut 1 with your fi ngers. Adjust 2. the height difference between the doors by turning the bolt 2 clockwise or counter clockwise . When you turn clockwise , the door will move up. After 3. adjusting the doors, turn the nut 1 clockwise until it reaches the lower end of the bolt, then tighten the bolt again with the wrench 3 to fi x the nut in place 1. If you do not secure the nut fi rmly, the bolt may release. LegLeg Screw DriverScrew Driver Screw DriverScrew Driver LegLeg Adjustment partAdjustment part When the door of the freezer is When the door of the freezer is higher than the fridgehigher than the fridge 3 2 1 WrenchWrench BoltBolt NutNut 3 2 WrenchWrench BoltBolt 3 2 1 WrenchWrench BoltBolt NutNut %4JOEC%4JOEC1.1.
12_ setting up CHECKING THE WATER DISPENSER LINE (OPTIONAL) A water dispenser is just one of the helpful features on your new Samsung refrigerator. To help promote better health, the Samsung water fi lter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You will need to purchase a water purifying system to do that. In order for the icemaker to operate properly, water pressure of 138~862 kPa is required. Under normal conditions, a 170 cc paper cup can be fi lled in 10 seconds. If the refrigerator is installed in an area with low water pressure (below 138 kPa), you can install a booster pump to compensate for the low pressure. Make sure the water storage tank inside the refrigerator is properly fi lled. To do this, press the water dispenser lever until the water runs from the water outlet. Water Line installation Kits are included. You can fi nd it in one of the freezer drawers. USING THE ICE MAKER (OPTIONAL) To Remove the Ice BucketHold the handle as shown in - fi gure1. Slightly pull up the bottom - part. Take out the ice bucket slowly. - To Refi t The Ice BucketAssemble it in the reverse - order of disassembly. Push the bucket in fi rmly until - you hear a clicking sound. When the bucket does not fi t - into its place, turn the gear handle on its back by 90 degrees and reinstall it again as shown in fi gure 2. Normal OperationAny sounds you hear when - the ice maker dumps ice into the bucket are part of normal operation. Not dispensing ice for long - periods may cause ice clumps in the ice bucket. Remove the remaining ice and empty the bucket. When ice does not come out, Check for any ice - stuck in the chute and remove it. The fi rst batch of ice cubes may be small due - to air in the pipe after connection, any air will be purged during normal use. - When ICE OFF blinks on the display panel, reinsert the bucket and/or make sure it’s installed properly. When the door is open, the Ice and water - dispenser do not work. If you close the door hard, it may cause water - spilling over the ice maker. To prevent dropping the ice bucket, use both - hands when removing it. To prevent injury, be sure to clean up any ice or - water that may have dropped on the fl oor. Do not let children hang on the ice dispenser or - on the bucket. They may get hurt. Be sure not to put your hand or any object into - the ice chute. It may cause personal injury or damage - mechanical parts. INSTALLING THE WATER DISPENSER LINE For Interior modelParts for water line Installation Connecting to the water supply linefi rst, shut off the main water supply line. 1. locate the nearest cold, drinking water line. 2. follow the Water line Installation Instructions in 3. the installation kit. CAUTION Figure2Figure2 Ice ChuteIce Chute Figure1Figure1 CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifi er to malfunction. 1 Water line fi xer and screws Water line fi xer and screws2 Pipe connector Pipe connector 3 Water line Water line4 Clip Clip 5 Water Filter Water Filter %4JOEC%4JOEC1.1.
setting up _13 01 SETTING UP After connecting the water supply to the water 4. fi lter, turn your main water supply back on and dispense about 1l to clear and prime the water fi lter. Connecting the water line to the refrigerator Remove the dust cap from the water line on the 1. rear of the unit and fi t a compression nut from the install kit. Remove the water pipe from the install kit and 2. fi t a compression nut to one end. Join the two pipes together using the 3. compression joint from the install kit ensuring that the joint is water tight. Join the other end of the install pipe to the main 4. water supply and turn on the water to check for leaks. Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6.5 mm of the plastic tubing to make sure you get a snug, leak- free connection. Before being used, the leakage in these places should be examined CAUTION Samsung Warranty does not cover WATER • LINE INSTALLATION. The cost of connection to a water supply is at • the customer expense, unless included in the delivery charge (refer to the delivery agreement with the seller) Please contact Plumber or Authorised Installer • for the installation if needed. If Water leakage occurs due to improper • installation, Please contact installer. INSTALLING THE WATER DISPENSER LINE For Exterior modelParts for water line Installation Connecting to the water supply line Connect the water pipe with coupler and tap. Close the main water tap. 1. Connect coupler “A” to the tap. 2. Close Main Close Main Water pipeWater pipe Close Main Close Main Water pipeWater pipeNo gapNo gap Water line fi xer and screwsWater line fi xer and screwsPipe connectorPipe connector Water lineWater linePurifi er lock-clipPurifi er lock-clipPurifi erPurifi er Remove Remove capcap Water Line from Water Line from unitunit Water Line from Water Line from KitKit No gapNo gap Loosen aLoosen a CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifi er to malfunction. %4JOEC%4JOEC1.1.
14_ setting up select the location where the purifi er is to install. (Model with the purifi er) If you wish to reassemble the water inlet - and outlet sides of the purifi er during purifi er installation, see the reference illustration. Cut the water line attached to the purifi er to the - appropriate place after measuring the distance between the purifi er and the cold water tap. Replacement InstructionsShut off water supply. 1. Note the Flow direction on the fi lter. 2. Insert water supply tube into the inlet side of the 3. fi lter until the tube stop. After inserting tube, put together the clip 4. strongly. The Clip fi x the tube. Turn on the water and check for leaks. If leaks 5. occur, repeat step 1,2,3,4. If leaks persist, discontinue use and call your supporting dealer. Flush fi lter for 5 minutes before use. 6. Remove any residual matter inside the purifi er. (Model with the purifi er) Open the main water tap to check whether - water is running through the water tube on the water inlet side of the purifi er. If water does not come out through the line, - check whether the tap is open. Leave the tap open until clean water is running - out and any residual matter that built up during manufacturing has been removed. Attach the purifi er lock-clip.Hold the purifi er - lock-clip in the appropriate position (under the sink for example) and fi x it tightly into place where to screw. Secure the purifi er in position.Fix the purifi er - in position, as shown in the fi gure on the right. WARRANTY INFORMATIONThis water line installation is not covered by the refrigerator or ice maker manufacturer’s warranty. Follow these instructions carefully to minimise the risk of expensive water damage. Note:If the coupler does not fi t on the current tap, go the nearest authorised service dealer and purchase the right couplers fi ttings. COUPLER “A”COUPLER “A” TAPTA P COUPLERCOUPLER SIDE OFSIDE OFPURIFIERPURIFIER WATER INLETWATER INLETSIDE OF PURIFIERSIDE OF PURIFIER LINE OUTLETLINE OUTLET 90 degree90 degree PURIFIER WATERPURIFIER WATERCAUTION Locking ClipLocking Clip Insert Locking Clip After Insert Locking Clip After tube seatedtube seated WATER SUPPLYWATER SUPPLYINLET SIDEINLET SIDEPERMEATPERMEAT FLOW DIRECTIONFLOW DIRECTION Note : You must also ensure that the cut is square and not at any sort of angle as this could cause a leak WATER LINEWATER LINE PURIFIERPURIFIER WATERWATER OUTLET SIDE OF OUTLET SIDE OF PURIFIERPURIFIER Purifi er lock-clipPurifi er lock-clip WATER TUBEWATER TUBE Purifi er lock-clipPurifi er lock-clip PURIFIERPURIFIER %4JOEC%4JOEC1.1.
setting up _15 01 SETTING UP Connect the water line to the refrigerator.Remove the compressor cover of the - refrigerator. Connect the water line to the valve, as shown in - the fi gure. When connected, check if there is any leakage. - If any, repeat the connection. Reattach the compressor cover of the - refrigerator. Secure the water line.Using clip ”A”, fi x the - water line to the wall (the back of refrigerator). When the water line - is secure, make sure whether the water line is not excessively bent, pinched or squashed. Removing any residual matter inside the water supply line after installing fi lter. Turn ON the main water supply & turn OFF the 1. valve to the water supply line. Run water through the dispenser until the water 2. runs clear (approx. 1 L). This will clean the water supply system and remove air from the lines. Additional fl ushing may be required in some 3. households. Open the refrigerator door and make sure there 4. are no water leaks coming from the water fi lter. A newly installed water fi lter cartridge may cause water to briefl y spurt from the water dispenser. This is due to air getting into the line. It should pose no problem to operation. WATER LINEWATER LINE INSTRUCTIONS COMPRESSOR INSTRUCTIONS COMPRESSOR COVER OF REFRIGERATORCOVER OF REFRIGERATOR CONNECTION NUTCONNECTION NUT CLIP ACLIP A WATER LINEWATER LINE %4JOEC%4JOEC1.1.
16_ operating OPERATING THE REFRIGERATOR Using the Control Panel / Digital Display 1 POWER FREEZE BUTTONSpeeds up the time needed to freeze products in the freezer. This can be helpful if you need to quickly freeze items that spoil easily or if the temperature in the freezer has warmed dramatically (For example, if the door was left open). 2 FREEZER BUTTONPress the Freezer button to set the freezer to your desired temperature, You can set the temperature between -14 °C (8 °F) and -25 ºC (-14 °F). 3 ICE TYPE BUTTONUse this button to choose Cubed, Crushed or to turn the Ice feature off. 4 FILTER CHANGE BUTTONWhen you change the fi lter, press this button for 3 seconds to reset the fi lter schedule. 5 VACATION BUTTONIf you are going on vacation or business trip or you do not need to use the refrigerator, press the Vacation button. When you select vacation button for fridge compartment off, display LED of Vacation will be on. It is strongly requested to remove foods in the fresh-food compartment and do not leave the door open when you select Vacation function. 6 CHILD LOCK FUNCTIONBy pressing the Vacation button and the Fridge button simultaneously for 3 seconds, all buttons will be locked. The Water dispenser lever and the Ice lever will not work either. To cancel this function, Press these two buttons for 3 seconds again. 7 FRIDGE BUTTONPress the Fridge button to set the fridge to your desired temperature. You can set temperature between 1 °C and 7 °C (34 °F and 45 °F). When you use Power Freeze the energy consumption of the refrigerator will increase. Remember to turn it off when you don’t need it and return the freezer to your original temperature setting. If you need to freeze large amount of food stuff, activate Power Freeze function at least 24 hours before. operating the SAMSUNG side- by-side refrigerator 5 6 7 1 3 4 2 COOLSELECT MODELCOOLSELECT MODEL DISPENSER MODELDISPENSER MODEL NORMAL MODELNORMAL MODEL %4JOEC%4JOEC1.1.
operating _17 02 OPERATING CONTROLLING THE TEMPERATURE Controlling the Freezer temperatureThe freezer temperature can be set between -14 °C (8 °F) and -25 ºC (-14 °F) to suit your particular needs. Press the Freezer button repeatedly until the desired temperature is shown in the temperature display. Keep in mind that foods like ice cream may melt at -16 ºC (4 °F). The temperature display will move sequentially from -14 °C (8 °F) and -25 ºC (-14 °F). When the display reaches -14 ºC (8 °F), it will begin again at -25 ºC (-14 °F). Five seconds after the new temperature is set the display will again show the actual current freezer temperature. However, this number will change as the Freezer adjusts to the new temperature. The door guards in the freezer of this model are the two star sections, so the temperature in two star sections are slightly higher than other freezer compartment. Controlling the Fridge temperatureThe refrigerator temperature can be set between 7 ºC (46 °F) and 1 ºC (34 °F) to suit your particular needs. Press the Fridge button repeatedly until the desired temperature is shown in the temperature display. The temperature control process for the Fridge works just like the Freezer process. Press the Fridge button to set your desired temperature. After a few seconds, the Fridge will begin tracking towards the newly set temperature. This will be refl ected in the digital display. The temperature of the freezer or the refrigerator may rise from opening the doors too frequently, or if a large amount of warm or hot food is placed in either side. This may cause the digital display to blink. Once the freezer and refrigerator return to their normal set temperatures the blinking will stop. If the blinking continues, you may need to “reset” the refrigerator. Try unplugging the appliance, wait about 10 minutes and then plug back in. USING THE ICE AND COLD WATER DISPENSER Press the Ice Type button to select the type of ice you want. Ice is made in cubes. When you select “Crushed”, the icemaker grinds the ice cubes into crushed ice. Dispensing ice Place your glass underneath the ice outlet and push gently against the ice dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the ice from bouncing out. Using the Water DispenserPlace a glass underneath the water outlet and push gently against the water dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the water from splashing out. No Ice Select this if you want to turn off the icemaker %4JOEC%4JOEC1.1.
18_ operating • Do not put your fi ngers, hands or any other unsuitable objects in the chute or ice-maker bucket. It may result in personal injury or material - damage. Never put fi nger or any other objects in the • dispenser opening. It may cause injury. - Use only the ice maker provided with the • refrigerator. The water supply to this refrigerator must only • be installed/connected by a suitably qualifi ed person and connect to a potable water supply only. In order to operate the ice maker properly, • water pressure of 138 ~ 862 kPa is required. • If you have a long vacation or business trip and won’t use water or ice dispensers, close the water valve. Otherwise, water leakage may occur. - Wipe excess moisture from the inside and leave • the doors open. Otherwise, odor and mold may develop. - To get more space,you can remove top freezer drawer since it does not affect thermal and mechanical characteristics. A declared storage volume of frozen food storage compartment is calculated with these drawers removed. For more space, you can store food with Guard FRE-UPP instead of the ice bucket. If you remove the ice bucket, ICE OFF will blink on the display panel. WARNING CAUTION USING THE COOLSELECT ZONE™ DRAWER (OPTIONAL) Quick Cool You can use the Quick Cool feature with the • CoolSelect ZoneTM. “Quick Cool” allows 1~3 canned beverages to • cool within 60 min. To cancel this function, press the “Quick Cool” • button again. CoolSelect ZoneTM returns to the previous temperature. When “Quick Cool” ends, it returns to the “Cool” • temperature setting. Thaw Drips loss and quality deterioration of meats • reduces the freshness of foods. After “Thaw” is selected, warm and cold air is • alternately supplied into the CoolSelect ZoneTM Drawer. Depending on the weight of meat, thawing time • can be selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs sequentially. When “Thaw” ends, CoolSelect ZoneTM display • returns to “Zero Zone” condition. When “Thaw “ ends, there are no juice in the • meats and they are half-freezed condition so it is easy to cut them for cooking. To cancel this option, press any button except • “Thaw”. The approximate thawing time of meat and fi sh • are shown below. (Based on 1 inch thickness) THAW TIME WEIGHT 4 hours 363 g (0.8 Ib) 6 hours 590 g (1.3 Ib) 10 hours 771 g (1.7 Ib) 12 hours 1000 g (2.2 Ib) Depending on the size and thickness of meat and fi sh, the thawing time may vary. The above weight represents the total weight of food in the CoolSelect ZoneTM Drawer. Ex) The total thawing time for 400 g frozen beef and 600 g frozen chicken will be 10 hours. With the “Thaw” option, food which is not needed to thaw in the CoolSelect ZoneTM Drawer should be removed. WARNINGGUARD FRE-UPPGUARD FRE-UPP(Optional)(Optional) %4JOEC%4JOEC1.1.
operating _19 02 OPERATING Zero Zone (0 ºC)When “Zero Zone” is chosen, the temperature • of the CoolSelect Zone™ Drawer is kept at 0 ºC regardless of the set refrigerator temperature. “Zero Zone” temperature helps keep meat or • fi sh fresh longer. CoolWhen “Cool” is chosen, the temperature will • be the same as the set temperature of the refrigerator. The digital panel shows the same temperature as that of the display panel. The CoolSelect Zone™ Drawer allows extra • refrigerator space. Depending on the beverages, the cool- down time may vary. For “Quick Cool” option, food stored in the CoolSelect ZoneTM Drawer should be removed. WARNING REMOVING THE FREEZER ACCESSORIES Cleaning and rearranging the interior of the freezer is simple. Remove the Glass shelf by pulling the shelf out 1. as far as it will go. Then, gently lift it up and remove it. Remove the door bin by holding the door bin 2. with both hands and then gently lift it up. Remove the Plastic drawer by pulling it out and 3. slightly lifting it up. ice bucket (freezer) 4. Remove the Icemaker Bucket by lifting up and pulling it out slowly. Grip the handle • as shown in the fi gure Lift the low part • slightly Take the ice • bucket out slowly. Do not use excessive force when removing the cover. Otherwise, the cover may break and cause injury. %4JOEC%4JOEC1.1.
20_ operating REMOVING THE FRIDGE ACCESSORIES Remove the spill Proof Glass Shelf by pulling 1. the shelf out as far as it will go. Then, gently lift it up and gently remove it. Remove the Vegetable & Fruit Drawer by 2. pressing on the indentations found on the inside left and right sides of the Veggie Box/Dry Box cover and remove by pulling forward. Holding the drawer with one hand, lift it up a little bit while pulling it forward and take it out of the refrigerator. Remove the Gallon Door Bin by holding the bin 3. with both hands and gently lifting it up. The Z Shelf is attached to the cabinet wall. 4. Remove the wine shelf by sliding it up and gently lifting the shelf out of the tabs. Ensure that the Z Shelf is fi tted as shown in the diagram and not upside down. CAUTION Before removing any accessories, make sure that no food is in the way. When possible, remove the food altogether to reduce the risk of accidents. To get the best energy effi ciency of this product, please leave all selves, drawers and baskets on their original position like as illustration in page (18). CLEANING THE REFRIGERATOR Do not use Benzene, Thinner or Clorox™ for cleaning. They may damage the surface of the appliance and can create a risk of fi re. Do not spray the refrigerator with water while it is plugged in, as it may cause an electric shock. Do not clean the refrigerator with benzene, thinner or car detergent for risk of fi re. REPLACING THE INTERIOR LIGHT For LED lamp, please contact service engineer to replace it. WARNING CAUTION %4JOEC%4JOEC1.1.