Samsung Plasma Display HP-P3761 User Manual
Have a look at the manual Samsung Plasma Display HP-P3761 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31 Changing Channels Using the Channel Buttons Press the CH or CH button to change channels. When you press the CH or CH button, the PDP changes channels in sequence. You will see all the channels that the PDP has memorized. (The PDP must have memorized at least three channels.) You will not see channels that were either erased or not memorized. Directly Accessing Channels Press the number buttons to go directly to a channel. For example, to select channel 27, press “2” then “7”. The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To select a channel over 100, press the +100 button. (For channel “112”, press the +100 button, then “1”, then “2”. To change to single-digit channels (0~9) faster, press “0” before the single digit. (For channel “4” press “0”, then “4”.) Using the PRE-CH button to select the previous channel Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. Adjusting the Volume Using the Volume Buttons Press the VOL or VOL button to increase or decrease the volume. Using Mute Using the MUTE Button At any time, you can temporarily cut off the sound using the MUTE button. 1 Press the MUTE button and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen. 2 To turn mute off, press the MUTE button again, or simply press the VOL or VOL button. Mute
32 Setting Up Your Remote Control This PDPs remote control can operate almost any VCR, Cable box or DVD. After it has been set up properly, your remote control can operate in five different modes: TV , VCR, CATV, DVD, or STB. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Notes : ●The remote control may not be compatible with all DVD Players, VCRs, Cable boxes. ●The remote control can only operate Set-Top Box made by Samsung. Setting Up the Remote to Operate Your VCR, Cable box or DVD player 1 Turn off your VCR (or Cable box, DVD player). 2 Press the MODE button. The Mode is changed whenever MODE button is pressed. 3 Press the SET button on your TVs remote control. 4 Using the number buttons on your remote control, enter three digits of the VCR (or Cable box, DVD player) code listed on page 33 of this manual for your brand of VCR (or Cable box, DVD). Make sure you enter three digits of the code, even if the first digit is a 0. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your VCR (or Cable box, DVD) should turn on if your remote is set up correctly. If your VCR (or Cable box, DVD) does not turn on after set up, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR (or Cable box, DVD). If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008). Notes •When your remote control is in “VCR”, “CATV”, or “DVD” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, and FF) still operate your VCR. •You do not need to program the remote for Samsung Set-Top Box as the codes are pre-programmed.
33 Remote Control Codes VCR Codes Cable Box Codes DVD Codes
34 Setting the Signal Source 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ENTER button to select “Source List”. 3 Press the ▲or ▼button to select signal source, then press the ENTER button. 4 Press the MENU button to exit. Note •When you connect equipment to the PDP, you can choose between the following sets of jacks: AV1, AV2, S-Video, Component1, Component2, or DVI on the PDP’s rear panel. Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as VCR, DVD, Set-Top box and the TV source (broadcast or cable). Source List : TV√ Edit Name√ Input TV MoveEnterReturn TV AV1- - - -AV2- - - -S-Video- - - -Component1- - - -Component2- - - -DVI- - - - Source List TV MoveEnterReturn TV AV1- - - -AV2- - - -S-Video- - - -Component1- - - -Component2- - - -DVI- - - - Source List TV MoveEnterReturn ➤ ➤Quick way to access viewing an external signal source : Just press the “SOURCE” button on the remote control.
Assigning Names to External input mode 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ▲or ▼button to select “Edit Name”, then press the ENTER button. 3 Press the ENTER button. Press the ▲or ▼button to select external device, then press the ENTER button. • You can select the VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, or DHR. • Set other signal sources (AV2, S-Video, Component1, Component2, or DVI) using the same method as listed above. 4 Press the MENU button to exit. Note •DHR : DVD HDD Recorder 35 Edit Name Source List : TV√ Edit Name√ Input TV MoveEnterReturn Edit Name AV1 :- - - -√AV2 :- - - -√S-Video :- - - -√Component1 :- - - -√Component2 :- - - -√DVI :- - - -√ Edit Name TV MoveEnterReturn AV1 :- - - -√AV2 :- - - -√S-Video :- - - -√Component1 :- - - -√Component2 :- - - -√DVI :- - - -√ Edit Name TV MoveEnterReturn - - - - VCR DVD Cable STB HD STB Satellite STB †
PLASMA DISPLAY PANEL Picture Control Customizing the Picture ................................................................38 Using Automatic Picture Settings ....................................................39 Selecting the Color Tone ................................................................40 DNIe (Digital Natural Image engine) ............................................41 Changing the Screen Size ............................................................42 Freezing the Picture ......................................................................44 Viewing the Picture-in-Picture ..........................................................45 Selecting a Signal Source (Antenna or Cable) for PIP ........................50 Setting the My Color Control Mode ................................................52
Customizing the Picture You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color, and Tint settings of your PDP. 38 1 Press the MENU button. Press the ▲or ▼button to select “Picture”, then press the ENTER button. 2 Press the ▲or ▼button to select “Custom”, then press the ENTER button. You will also see the items “Contrast”, “Brightness”, “Sharpness”, “Color”, and “Tint”. 3 Press the ▲or ▼ button to select the item you wish to change, then press the ENTER button. Press the œor √button to change the value of the item. 4 Press the MENU button to exit. Notes •In the DVI mode, you can’t adjust the Color and Tint. •If you make any changes to these settings, the picture standard is automatically switched to custom. Mode : Dynamic√Custom√Color Tone : Normal√Film Mode : Off√Size : 16:9√PIP√DNIe : On√My Color Control√ Picture TV MoveEnterReturn Contrast 100 Brightness 45 Sharpness 75 Color 55 Tint G 50 R 50 Custom TV MoveEnterReturn Contrast 100
39 1 Press the MENU button. Press the ▲or ▼button to select “Picture”, then press the ENTER button. 2 Press the ENTER button to select “Mode”. 3 Press the ▲or ▼button to select “Dynamic”, “Standard”, “Movie”, or “Custom” picture setting, then press the ENTER button. 4 Press the MENU button to exit. •Choose Dynamic for viewing the TV during the day or when there is bright light in the room. •Choose Standard for the standard factory settings. •Choose Movie when viewing the movie. •Choose Custom if you want to adjust the settings according to personal preference (see “Customizing the Picture”, page 38). Using Automatic Picture Settings Your PDP has automatic picture settings that allow you to easily adjust the video display. ➤ ➤Quick way to access the picture setting: Just press the “P.MODE” button on the remote control. Mode : Dynamic√Custom√Color Tone : Normal√Film Mode : Off√Size : 16:9√PIP√DNIe : On√My Color Control√ Picture TV MoveEnterReturn Mode :Custom Custom Color Tone : Normal Film Mode : Off Size : 16:9 PIP DNIe : On My Color Control Picture TV MoveEnterReturn Mode :Custom Custom Color Tone : Normal Film Mode : Off Size : 16:9 PIP DNIe : On My Color Control Picture TV MoveEnterReturn Dynamic Standard Movie Custom Dynamic Standard Movie Custom
40 Selecting the Color Tone 1 Press the MENU button. Press the ▲or ▼button to select “Picture”, then press the ENTER button. 2 Press the ▲or ▼button to select “Color Tone”, then press the ENTER button. 3 Press the ▲or ▼button to select “Cool2”, “Cool1”, “Normal”, “Warm1”, or “Warm2”, then press the ENTER button. •You can select “Cool”, “Normal” or “Warm” in DVI mode. 4 Press the MENU button to exit. Mode : Dynamic√Custom√Color Tone : Normal√Film Mode : Off√Size : 16:9√PIP√DNIe : On√My Color Control√ Picture TV MoveEnterReturn Mode : Dynamic Custom Color Tone :Normal Film Mode : Off Size : 16:9 PIP DNIe : On My Color Control Picture TV MoveEnterReturn Cool2 Cool1 Normal Warm1 Warm2 Mode : Dynamic Custom Color Tone :Normal Film Mode : Off Size : 16:9 PIP DNIe : On My Color Control Picture TV MoveEnterReturn Cool2 Cool1 Normal Warm1 Warm2