Samsung Plasma Display HP-P3761 User Manual

							11
1 
Remove the screws from the back of the PDP.
2 
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire a specialist to install the wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened. Otherwise the PDP may fall.
Note
•A 5 inch(12.7 cm) gap is needed between the back of the Plasma TV and the wall.
Fixing the PDP panel to the wall attachment panel bracket
3 
Tighten the screws of the insulation
holders to the back of the PDP.
4 
Put the 4 insulation holders on the PDP
in the grooves of the wall mount 
bracket and pull down on the PDP (Œ) 
to secure it to the wall mount bracket 
(´). Tighten the screws as shown (ˇ) 
so that the PDP cannot be separated 
from wall mount bracket.
PDP panel
Wall attachment
panel bracketWall 
						

							➤ ➤Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage to the screen. 
Always store the PDP upright.
12
1
Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided.
How to Assemble the Stand-Base 
						

							PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................14
Connecting Cable TV ....................................................................15
Connecting a VCR ........................................................................17
Connecting a Camcorder ..............................................................18
Connecting a DVD Player ..............................................................19
Connecting a DTV Receiver ..........................................................20 
						

							Connecting VHF and UHF Antennas
14
Antennas with 75-ohm Round Leads
If your antenna looks like this:  it has 75-ohm round leads.  
1
Plug the antenna lead into the VHF/UHF terminal 
on the PDP.
Use the antenna cable included in the product 
package.  
						

							15
Connecting Cable TV
You can connect different cable systems to your PDP, including cable without a cable box, 
and cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
1 
Plug the incoming cable into the VHF/UHF terminal on
the PDP.
Use the antenna cable included in the product 
package. 
Cable with a Cable Box that Descrambles All Channels
1 
Find the cable connected to the ANTENNA OUT 
terminal on your cable box. This terminal might be 
labeled ANT OUT, VHF OUT or simply OUT.
2
Connect the cable to the VHF/UHF terminal on the 
PDP. 
Use the antenna cable included in the product 
package.  
						

							16
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the cable that is 
connected to the ANTENNA IN terminal of
your cable box. 
This terminal might be labeled ANT IN, 
VHF IN or simply, IN. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable between an 
OUTPUT terminal of the splitter and the 
IN terminal of the cable box.
3
Connect a coaxial cable between the
ANTENNA OUT terminal of the cable box 
and the B-IN terminal of the A/B switch.
4
Connect a coaxial cable between the
ANTENNA OUT terminal of the cable box 
and the B-IN terminal of the A/B switch.
5
Connect the last coaxial cable between the
OUT terminal of the RF (A/B) switch and 
the VHF/UHF terminal on the PDP.
After youve made this connection, set the A/B switch to the A position for normal viewing. 
Set the A/B switch to the B position to view scrambled channels. (When you set the A/B switch 
to B, you will need to tune your Set-Top Box to the cable boxs output channel, which is usually
channel 3 or 4.) 
						

							17
Connecting a VCR 
Connecting a VCR to the Video or S-Video/Audio jack
S-Video cable Audio cable
Video cablePower cord
Connect the video/audio cables between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the 
PDP and VIDEO or S-VIDEO / L - AUDIO - R output jacks on the VCR. (Note: For better video, 
use an S-Video cable.)
Note
•Please be sure to match the color coded input terminals and cable jacks.
Videotape Playback:
1. Turn on your PDP.
2. Press the SOURCE button to select “Video(AV1 or AV2)” or “S-Video”.
3. Turn on your VCR, insert a videotape and press the play button.
How to Connect
PDP VCR 
						

							18
Connecting a Camcorder
Connect a Video/Audio cable between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the 
PDP and the VIDEO or S-VIDEO /AUDIO output jacks on the camcorder. (Note: For better
video, use an S-VIDEO cable.)
Note
•Please be sure to match the color-coded input terminals and cable jacks.
Viewing Tapes
1. Turn on your PDP.
2. Press the SOURCE button to select “Video(AV1 or AV2)” or “S-VIDEO”.
3. Turn on your camcorder and set it to Video Mode. (For details, refer to your camcorder 
Owner’s instructions.)
4. Set the IN/OUT switch on your camcorder to OUT.
5. Insert the tape into the camcorder and press the Play button.
How to Connect
Viewing camcorder tapes
S-Video cable Audio cable
Video cablePower cord PDPCamcorder 
						

							19
Connecting a DVD Player (480i, 480p)
This PDP displays the optimum picture in 720p mode.
Playing DVD
Connect a video cable between the Y, Pb, Pr(COMPONENT1, 2) input jacks on the PDP 
and Y/P
B/PRoutput jacks on the DVD player.
Connect an audio cable between the AUDIO L/R(COMPONENT1, 2) input jacks on the PDP
and the AUDIO output jacks on the DVD player.
Note
•Please be sure to match the color-coded input terminals and cable jacks.
To Play DVD:
1. Turn on your PDP.
2. Press the SOURCE button to select “COMPONENT1” or “COMPONENT2”.
3. Turn on your DVD player, insert a DVD disc and press the Play button.
• For an explanation of Component video, see your DVD owner’s instructions.
How to Connect
1
2
Component cable
Audio cable Power cord PDPDVD Player 
						

							Connecting a DTV Receiver
(480p, 720p, 1080i)
This PDP displays the optimum picture in 720p mode.
20
Watching DTV
Connect the cable or antenna to the antenna input jack on the DTV.
Connect a video cable between the Y, P
b, Pr(COMPONENT 1, 2) or DVI jack on the PDP
and the Y, P
B, PR(COMPONENT) or DVI output jacks on the DTV receiver.
Connect an audio cable between the COMPONENT 1, 2 (L/R AUDIO) or DVI (L/R AUDIO)
jacks on the  PDP and the AUDIO OUTPUT jacks on the DTV receiver.
Notes
•Please be sure to match the color-coded input terminals and cable jacks.
•Connecting a PC using the DVI connection is not supported.
To Watch DTV:
1. Turn on your PDP.
2. Press the SOURCE button to select “COMPONENT1”, “COMPONENT2” or “DVI”.
3. Turn on your DTV receiver.
• For an explanation of Component video, see your DTV receiver owner’s instructions.
How to Connect
1
2
3
Use a DVI-D video cable. (sold separately)
Audio cable Component cable
DVI cablePower cord PDP
DTV Receiver
or