Samsung ML 3470D User Manual

2.6   
Changing the font setting
Your machine has preset the font for y our region or country. If you want 
to change the font which you pref er or set the font under special 
condition such as the DOS environmen t, you can change the font setting 
as follows:
1 Press  Menu on the control panel until you see  Emulation feature.
2 Press  OK to access the font setting.
3 Press the left/right arrow until  Setup displays.
4 Press the left/right arrow until  PCL displays.
5 Press the left/right arrow until...

3.1   
3 Software overview
This chapter gives you an overview of  the software that comes with your 
printer. Further details about installing and using the software are 
explained in the  Software Section .
This chapter includes:
• Supplied software
• Printer driver features
• System requirements
Supplied software
After you have set up your machine a nd connected it to your computer, 
you must install the printer software. If you are a Windows or Macintosh 
OS, install the software from the s upplied...

3.2   
Printer driver features
Your printer drivers support th e following standard features:
•  Paper source selection
•  Paper size, orientation and media type
•  Number of copies
In addition, you can use various spec ial printing features. The following 
table shows a general overview of fe atures supported by your printer 
drivers: 
FeaturePCL 6 PostScript
WindowsWindowsMacintoshLinux
Toner save O O O O
Print quality 
option OO OO
Poster 
printing O
XXX
Multiple 
pages per 
sheet (N-up) O O O O...

3.3   
Linux
Macintosh
ItemRequirements
Operating system • Red Hat 8.0 ~ 9.0 • Fedora Core 1 ~ 4
• Mandrake 9.2 ~ 10.1
• SuSE 8.2 ~ 9.2
Processor Pentium IV 1 GHz or higher
RAM 256 MB or higher
Free disk page 1 GB or higher
Software • Linux Kernel 2.4 or higher • Glibc 2.2 or higher
• CUPS
•SANE
OPERATING SYSTEM
REQUIREMENT (RECOMMENDED)
CPURAMFREE HDD 
SPACE
Mac OS X 10.4 
or lower •Power PC 
G4/G5
• Intel 
processors • 128 MB for a Power 
PC based Mac 
(512 MB)
• 512 MB for an Intel  based Mac (1 GB)...

4.1   
4 Network setup(ML-3471ND only)
This chapter gives you st ep-by-step instructions for setting up your 
printer for network connections.
This chapter includes:
• Introduction
• Supported operating systems
• Configuring TCP/IP
• Using SetIP program
• Configuring EtherTalk
• Setting Ethernet speed
• Restoring the network configuration
• Printing a network configuration page
Introduction
Once you have connected your printer to a network with an RJ-45 
Ethernet cable, you can share the printer with...

4.2   
Configuring TCP/IP
Your printer can be set up with a variety of TCP/IP network information, 
such as an IP address, a subnet mask, a gateway, and DNS addresses. 
There are several ways in which your printer can be assigned a TCP/IP 
address, depending on your network.
•  Static addressing: A TCP/IP address is assigned manually by the 
system administrator.
•  Dynamic addressing via BOOTP/DHCP (default): A TCP/IP address  is assigned automatically by the server.
Note 
Before configuring TCP/IP,...

4.3   
Configuring EtherTalk
EtherTalk is AppleTalk used in an Ethernet network. This protocol is 
widely used in Macintosh network env ironments. To use EtherTalk, take 
the following step:
1 Press  Menu until Network  appears on the bottom line of the 
display and press  OK.
2 Press the  scroll buttons until  EtherTalk appears and press  OK.
3 Press the  scroll buttons until  On appears and press  OK.
4 Press  Stop to return to Standby mode.
Setting Ethernet speed
You can select the communication...

5.1   
5 Loading print media
This chapter will help you understand types of paper you can use with 
your printer and how to properly load paper in the different paper trays 
for the best print quality. 
This chapter includes:
• Selecting print media
• Loading paper
• Selecting an output location
Selecting print media
You can print on a variety of print media, such as plain paper, envelopes, 
labels, and transparencies. Always use print media that meet the 
guidelines for use with your printer.  Print...

5.2   
Supported sizes of paper
Note
For duplex printing, A4, Letter, Oficio , Legal, and Folio sizes are supported.
Ty p eSizeDimensionsWeighta
a. If media weight is over 24 lb (90 g/m2), use the multi-purpose tray.
Capacityb
b. Maximum capacity may differ depending on media  weight, thickness, and environmental conditions.
Plain paperLetter 215.9 x 279 mm (8.5 x 11 inches)
• 60 to 90 g/m
2 (16 to 24 lb 
bond ) for the tray
• 60 to 163 g/m
2 (16 to 43 lb 
bond ) for the multi-
purpose tray • 250 sheets...

5.3   
Guidelines for selecting  and storing print media
When selecting or loading paper, env elopes, or other print materials, 
keep these guidelines in mind:
•  Always use print media that confo rm with the specifications listed on 
page 5.3.
•  Attempting to print on damp, curl ed, wrinkled, or torn paper can cause 
paper jams and poor print quality.
•  For the best print quality, use only high quality copier grade paper  specifically recommended for use in laser printers.
•  Avoid using the...