Samsung ML 2950ND User Manual
Have a look at the manual Samsung ML 2950ND User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2. Using a network-connected machine This chapter gives you step-by-step instructions for setting up a network connected machine and software. • Useful network programs 12 • Wired network setup 13 • Installing driver over the network 17 • IPv6 configuration 27 • Wireless network setup 30 Downloaded From ManualsPrinter.com Manuals
122. Using a network-connected machineUseful network programs There are several programs available to setup the network settings easily in a network environment. For the network administrator especially, managing several machines on the network is possible. Before using the programs below, set the IP address first. 1 SyncThru™ Web Service The web server embedded on your network machine allows you to do the following tasks (see "Using SyncThru™ Web Service" on page 29): • Check the supplies information and status. • Customize machine settings. • Set the email notification option. When you set this option, the machine status (toner cartridge shortage or machine error) will be sent to a certain person's email automatically. • Configure the network parameters necessary for the machine to connect to various network environments. 2 SyncThru™ Web Admin Service Web-based machine management solution for network administrators. SyncThru™ Web Admin Service provides you with an efficient way of managing network devices and lets you remotely monitor and troubleshoot network machines from any site with corporate internet access. Download this program from http:// solution.samsungprinter.com. 3 SetIP This utility program allows you to select a network interface and manually configure the IP addresses for use with the TCP/IP protocol. • See "IPv4 configuration using SetIP (Windows)" on page 13. • See "IPv4 configuration using SetIP (Macintosh)" on page 15. • See "IPv4 configuation using SetIP (Linux)" on page 15. TCP/IPv6 is not supported by this program. Downloaded From ManualsPrinter.com Manuals
132. Using a network-connected machineWired network setup You must set up the network protocols on your machine to use it on your network. You can use network after connecting network cable to a corresponding port on your machine. • For models that do not have the display screen on the control panel, use the SyncThru™ Web Service or SetIP program. - See "Using SyncThru™ Web Service" on page 61. - See "Setting IP address" on page 13. • For models that have the display screen on the control panel, configure the network setting by pressing (Menu) button > Network on the control panel. 4 Printing a network configuration report You can print Network Configuration Report from the machine’s control panel that will show the current machine’s network settings. This will help you to set up a network. •The machine has the display screen: Press the (Menu) button on the control panel and select Network > Network Config. (Network Configuration)> Yes. •The machine does not have the display screen: Press the (Cancel or Stop/Clear) button for more than five seconds on the control panel.Using this Network Configuration Report, you can find your machine’s MAC address and IP address. For example: • MAC Address: 00:15:99:41:A2:78 • IP Address: 192.0.0.192 5 Setting IP address First, you have to set up an IP address for network printing and managements. In most cases a new IP address will be automatically assigned by a DHCP (Dynamic Host Configuration Protocol) server located on the network. IPv4 configuration using SetIP (Windows) Before using the SetIP program, disable the computer firewall from Control Panel > Security Center > Windows Firewall. The following instructions may differ for your model. Downloaded From ManualsPrinter.com Manuals
Wired network setup142. Using a network-connected machine 1Install this program from the supplied CD-ROM by double- click Application > SetIP > Setup.exe. 2 Follow the instructions in the installation window. 3 Connect your machine to the network with a network cable. 4 Turn on the machine. 5 From the Windows Start menu, select All Programs > Samsung Printers > SetIP > SetIP. 6 Click the icon (third from left) in the SetIP window to open the TCP/IP configuration window. 7 Enter the machine’s new information into the configuration window as follows. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding. Find the machine’s MAC address from the Network Configuration Report (see "Printing a network configuration report" on page 13) and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8. 8 Click Apply, and then click OK. The machine will automatically print the Network Configuration Report. Confirm that all the settings are correct. Downloaded From ManualsPrinter.com Manuals
Wired network setup152. Using a network-connected machine IPv4 configuration using SetIP (Macintosh) Before using the SetIP program, disable the computer firewall from System Preferences > Security > Firewall. The following instructions may vary from your model. 1Connect your machine to the network with a network cable. 2 Insert the Installation CD-ROM, and open the disk window, select MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html. 3 Double-click the file and Safari will automatically open, then select Trust. The browser will open the SetIPapplet.html page that shows the printer’s name and IP address information. 4 Click the icon (third from left) in the SetIP window to open the TCP/IP configuration window. 5 Enter the machine’s new information into the configuration window. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding. Find the machine’s MAC address from the Network Configuration Report (see "Printing a network configuration report" on page 13) and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8. 6 Select Apply, then OK, and OK again. 7 Quit Safari. IPv4 configuation using SetIP (Linux) Before using the SetIP program, disable the computer firewall from System Preferences or Administrator. The following instructions may vary from your model or operating systems. 1Open /opt/Samsung/mfp/share/utils/. 2 Double-click the SetIPApplet.html file. 3 Click to open the TCP/IP configuration window. Downloaded From ManualsPrinter.com Manuals
Wired network setup162. Using a network-connected machine 4 Enter the machine’s new information into the configuration window. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding. Find the machine’s MAC address from the Network Configuration Report (see "Printing a network configuration report" on page 13) and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8. 5 The machine will automatically print the Network Configuration Report. Downloaded From ManualsPrinter.com Manuals
172. Using a network-connected machineInstalling driver over the network 6 Windows 1Make sure that the machine is connected to the network and powered on. Also, your machine’s IP address should have been set (see "Setting IP address" on page 13). If the “Found New Hardware Wizard” appears during the installation procedure, click Cancel to close the window. 2 Insert the supplied software CD into your CD-ROM drive. The software CD should automatically run and an installation window will appear. 3 Select Install Now. The Custom Installation allows you to select the machine’s connection and choose individual components to install. Follow the instructions on the window. 4 Read License Agreement, and select I accept the terms of the License Agreement. Then, click Next. The program searches for the machine. If your machine is not found on the network or locally, an error message appears. Select the option you want and click Next. 5 The searched machines will be shown on the screen. Select the one you wish to use and click OK. If the driver searched only one machine, the confirmation window appears. 6 Follow the instructions in the installation window. Silent installation Mode Silent installation mode is an installation method that does not require any user intervention. Once you start the installation, the machine driver and software are automatically installed on you computer. You can start the silent installation by typing /s or /S in the command window. ►Command-line Parameters Following table shows commands that can be used in the command window. Downloaded From ManualsPrinter.com Manuals
Installing driver over the network182. Using a network-connected machine Following command-line are effective and operated when command is used with /s or /S. But /h, /H or /? are exceptional commands that can be operated solely. Command- lineDefinitionDescription /s or /SStarts silent installation. Installs machine drivers without prompting any UIs or user intervention. /p”” or /P””Specifies printer port. Network Port will be created by use of Standard TCP/IP Port monitor. For local port, this port must exist on system before being specified by command. Printer port name can be specified as IP address, hostname, USB local port name or IEEE1284 port name. For example • /p”xxx.xxx.xxx.xxx” in where, “xxx.xxx.xxx.xxx” means IP address for network printer. / p”USB001”, /P”LPT1:”, /p”hostname” • When installing the driver silently in Korean, type in- Setup.exe /s / L"0x0012” or Setup.exe /s. Command- lineDefinitionDescription Downloaded From ManualsPrinter.com Manuals
Installing driver over the network192. Using a network-connected machine /a”” or /A””Specifies destination path for installation. The destination path should be a fully qualified path. Since machine drivers should be installed on the OS specific location, this command applies to only application software. Command- lineDefinitionDescription /i”” or /I””Specifies customized install script file for custom operation. The script filename should be a fully qualified filename. Customized script file can be assigned for customized silent installation. This script file can be created or modified through provided installer customizing utility or by text editor. Note: This customized script file is prior than default installer setting in setup package but not prior than command- line parameters. /n”” or /N””Specifies printer name. Printer instance shall be created as specified printer name.With this parameter, you can add printer instances as your wishes. Command- lineDefinitionDescription Downloaded From ManualsPrinter.com Manuals
Installing driver over the network202. Using a network-connected machine /nd or /NDCommands not to set the installed driver as a default machine driver.It indicates installed machine driver will not be the default machine driver on your system if there are one or more printer drivers installed. If there is no installed machine driver on your system, then this option won’t be applied because Windows OS will set installed printer driver as a default machine driver. /x or /XUses existing machine driver files to create printer instance if it is already installed.This command provides a way to install a printer instance that uses installed printer driver files without installing an additional driver. Command- lineDefinitionDescription /up”” or /UP””Removes only specified printer instance and not the driver files.This command provides a way to remove only specified printer instance from your system without effecting other printer drivers. It will not remove printer driver files from your system. /d or /DUninstalls all device drivers and applications from your system.This command will remove all installed device drivers and application software from your system. /v”” or /V””Shares installed machine and add other available platform drivers for Point & Print.It will install all supported Windows OS platform’s machine drivers to system and share it with specified for point and print. /o or /OOpens Printers and Faxes folder after installation.This command will open Printers and Faxes folder after the silent installation. Command- lineDefinitionDescription Downloaded From ManualsPrinter.com Manuals