Samsung ML 2851ND User Manual

1.2   
Machine features
The table below lists a general overview of features supported by your 
printer.
(I: Installed, O: Option, NA: Not Available)
FeaturesML-2850DML-2851ND
USB 2.0
(USB 2.0: Hi-Speed USB 2.0)II
Network Interface
(Ethernet 10/100 Base TX)NA I
PCL EmulationII
PostScript EmulationII
Duplex printinga
a. Printing on both sides of paper.
II
Printer overview
Front view
1
output tray6
tray 1
2
control panel7
optional tray 2 
3
control board cover8
paper level indicator
4
front cover9
output...

1.3   
Rear view
Control panel overview
1
network porta
a. ML-2851ND only.
4
duplex unit
2
USB port5
power receptacle
3
optional tray 2 cable 
connector6
power switch
1
Error: Indicates the status of your printer. See page 9.5.
2
Online: Indicates the status of your printer. See page 9.5.
3
Cancel: Prints a demo page or configuration page. 
Cancels the print job. 
Makes the printer pick up the print media.
* The figure above shows an ML-2851ND.
Understanding the LEDs
 
LEDStatusDescription
Error Red On •...

1.4   
Finding more information
You can find information for setting up and using your printer from the 
following resources, either printed or onscreen.
Quick Install 
GuideProvides information on setting up your 
printer, therefore, be sure to follow the 
instructions in the guide to get the printer 
ready.
Online User’s 
GuideProvides you with step-by-step instructions for 
using your printer’s full features, and contains 
information for maintaining your printer, 
troubleshooting, and installing...

1.5   
Place the machine on a flat and stable surface for not letting it tilt 
more than 2 mm (0.08 inches). Otherwise, it may affect the printing 
quality. 
2Unpack the machine and check all the enclosed items.
3Remove the tape holding the machine tightly.
4Install the toner cartridge.
5Load paper. (See Loading paper on page 4.4.)
6Make sure that all the cables are connected to the machine. 
7Turn the machine on. 
Caution
•This equipment will be inoperable when mains power fails.
•When you move the...

1.6   
Changing the font setting
Your machine has preset the font for your region or country. 
If you want to change the font or set the font for special conditions such 
as DOS environment, you can change the font setting as follows: 
1Ensure that you have installed the printer driver from the provided 
software CD.
2Double-click the Smart Panel icon on the Windows task bar (or 
Notification Area in Linux). You can also click Smart Panel on the 
status bar in Mac OS X.
3Click Printer Setting.
4Click...

2.1   
2 Basic setup
This chapter includes:
• Printing a demo page
• Using toner save mode
Printing a demo page
After setting up your printer, print a demo page to make sure that the 
printer is operating correctly.
Press and hold the Cancel button for about 2 seconds.
A demo page prints out.
Using toner save mode
Toner save mode allows the printer to use less toner on each page. 
Activating this mode extends the life of your toner cartridge and reduces 
your cost per page beyond what one would...

3.1   
3 Software overview
This chapter gives you an overview of the software that comes with your 
printer. Further details about installing and using the software are 
explained in the Software Section.
This chapter includes:
• Supplied software
• Printer driver features
• System requirements
Supplied software
After you have set up your machine and connected it to your computer, 
you must install the printer software. If you are a Windows or Macintosh 
OS, install the software from the supplied CD and...

3.2   
System requirements
Before you begin, ensure that your system meets the following 
requirements:
Windows
Note
Internet Explorer 5.0 or higher is the minimum requirement for 
all Windows operating systems.
Users who have an administrator right can install the software.
OPERATING 
SYSTEM
REQUIREMENT (RECOMMENDED)
CPURAMFREE HDD 
SPACE
Windows 
2000Pentium II 400 MHz 
(Pentium III 933 MHz)64 MB 
(128 MB)600 MB
Windows XPPentium III 933 MHz 
(Pentium IV 1 GHz)128 MB 
(256 MB)1.5GB
Windows 
Server...

4.1   
4 Loading print media
This chapter will help you understand the types of paper you can use 
with your printer and how to properly load paper in the different paper 
trays for the best print quality. 
This chapter includes:
• Selecting print media
• Loading paper
• Printing with a prescribed paper size
• Knowing an output location
Selecting print media
You can print on a variety of print media, such as plain paper, envelopes, 
labels, and transparencies. Always use print media that meet the...

4.2   
Supported sizes of paper
Note
For duplex printing, A4, Letter, Oficio, Legal, and Folio sizes are supported.
Ty p eSizeDimensionsWeighta
a. If media weight is over 24 lb (90 g/m2), use the manual feed.
Capacityb
b. Maximum capacity may differ depending on media weight, thickness, and environmental conditions.
Plain paperLetter 216 x 279 mm (8.5 x 11 inches)
• 60 to 105 g/m
2 (16 to 28 lb 
bond ) for the tray
• 60 to 163 g/m
2 (16 to 43 lb 
bond ) for the manual feed• 250 sheets of 75 g/m
2 
(20 lb...