Samsung Le 32m61bs Owners Instructions

							
English-59

Troubleshooting: Before Contacting Ser vice Personnel

Before contacting Samsung after-sales service, perform the following sim\
ple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of your
set and contact your local dealer.

No sound or picture
Normal picture but no sound
No picture or black and white picture
Sound and picture interference
Blurred or snowy picture,
distorted sound
Remote control malfunctions
“Check signal cable.” message is displayed.
On PC mode, “Not Supported Mode.” 
message is displayed.
The image is too light or too dark.
On PC mode, horizontal bars appear to flicker,
jitter or shimmer on the image.
On PC mode, vertical bars appear to flicker,
jitter or shimmer on the image.
On PC mode, screen is black and power 
indicator light blinks every 1 second.
On PC mode, image is not stable and 
may appear to vibrate.
On PC mode, image is not centered 
on the screen.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the 
POWER
buttons on the lower-right
panel.
Check the picture contrast and brightness settings.
Check the volume.
Check the volume.
Check whether the 
MUTE
button has been pressed on the remote control.
Check if 
Internal Mute
is off
Adjust the colour settings.
Check that the broadcast system selected is correct.
T ry to identify the electrical appliance that is affecting the set and move it
further away.
Plug your set into a different mains socket.
Check the direction, location and connections of your aerial.
This interference is often due to the use of an indoor aerial.
Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check the battery terminals.
Check that the signal cable is firmly connected to the PC or video sourc\
es.
Check that the PC or video sources are turned on.
Check the maximum resolution and the frequency of the video adapter.
Compare these values with the data in the Display Modes. 
Adjust the Brightness and Contrast.
Adjust the Fine function.
Adjust the Coarse function and then adjust the Fine function.
The TV is using its power management system.
Move the computer’s mouse or press any key on the keyboard.
Check that the display resolution and frequency from your computer or
video board is an available mode for your set. On your computer check:
Control Panel, Display, Settings.
If the setting is not correct, use your computer utility programme to ch\
ange
the display settings. 
Your set supports multiscan display functions within the following
frequency domain:
Horizontal frequency(kHz): 30~ 61
V ertical frequency(Hz): 60~75
Maximum refresh rate (at 60Hz): 1360 X 768
Adjust the horizontal and vertical position.

The TFT LCD panel uses a panel consisting of sub pixels (3,147,264) which requ\
ire sophisticated technology to produce. However,
there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

01 BN68-00956D-04Eng.qxd  11/29/05  4:15 PM  Page 59
 
						

							
English-60

Installing the Wall Mount Kit

This installation is to be used when attaching the wall mount to a concr\
ete wall.
When attaching to other building materials, please contact your nearest \
dealer.

Components (Sold separately)

Wall-Bracket Set-Bracket Screw: 8EA

Wood Screw: 7EA Anchor: 7EA Screw: 3EA Installation Guide

How to assemble the Wall Mount Bracket

1
Mark the location of hole on the wall.
Drill a hole of 35mm depth on the marked
location.Fix anchors on each hole on the wall.
Connect wall-bracket to the wall with wood
screws after fitting anchors into the 
wall-bracket
.

Note: If the bracket is not firmly fixed to the wall,
LCD TV can fall off.

M6 X L14
M4 X L25 M4 X L8

02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 60
 
						

							
English-61

Installing the Wall Mount Kit

2  Turn the power off and unplug the power cord from the outlet.Place the TV faced down on a soft cloth or cushion on a table.
Remove the four screws from the back of the TV.
Separate the stand from the TV.
Cover the bottom hole with a cap
Loosen two screws on the rear side of the TV set (only model LE40M6 applied).
Attach the set-bracket onto the rear side of the TV set and secure the screws .
For 40 inches model, attach the bracket into the two holes with the two \
screws removed
in step 6 above.

3  Insert three Hangers of the set-bracket into the grooves of the wall-bracket .
Fix set-bracket and wall-bracket with screws .

Note: Before installing the set on the wall, connect the cables to the s\
et first.

How to assemble the Wall Mount Bracket

(Only Model LE40M6 Applied)

02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 61
 
						

							
English-62

Installing the Stand

1.  
Place the TV faced down on a soft cloth or cushion on a table.

2.  
Attach the stand to the TV set as shown in the picture.

3.  
Use the four screws to tightly fix the stand.

< 2 > < 3 >

Stand Swivel Function 

Maximizing space is available with Stand swivel functionThis product supports left/right swivel function on the desk.•You can adjust the angle up to 15° to the left or right.

Please move away all the stuff
around the monitor. 
There should be enough space  between the wall and the
monitor. 
Place the monitor on a flat and stable space to easily swivel
the TV.

-15° ~ 15°

02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 62
 
						

							
English-63

Using the Anti-Theft Kensington Lock

1.  
Insert the locking device into the Kensington slot on the LCD TV (Figure 1), and turn it in the locking direction
(Figure 2).

2.  
Connect the Kensington lock cable.

3.  
Fix the Kensington lock to a desk or a heavy stationary object.

The Kensington lock is a device used to physically fix the system when u\
sing it in a public place.
The locking device has to be purchased separately. The appearance and locking method may differ
from the illustration depending on the manufacturer. Please refer to the manual provided with the
Kensington lock for proper use.
The place of the Kensington Lock may be different depending on its model.

Cable
Figure 1
Figure 2


02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 63
 
						

							
English-64

Technical and Environmental Specifications

Model NameLE32M6/LE32M61BS LE40M6/LE40M61BS
Panel
Size 32" Diagonal (16:9) 40" Diagonal (16:9)
Display Size 697.68 (H) x 392.26 (V) mm 885.17(H) x 497.66(V) mm
(27.47 (H) x 15.44 (V) inches) (34.85(H) x 19.59(V) inches)
T ype a-si TFT active matrix a-si TFT active matrix
Pixel Pitch 0.511 (H) x 0.511 (V) mm 0.648(H) x 0.216(V) mm (0.0201 (H) x 0.0201(V) inches) (0.027(H) x 0.0085(V) inches)
V iewing Angle 178/178  (H/V) 178/178(H/V)
Resolution 1366 (H) x 768 (V) 1366(H) x 768(V)

Frequency
Horizontal 30 ~ 61 kHz 30 ~ 61 kHz
V ertical 60 ~ 75 Hz 60 ~ 75 Hz
Display Colour 16,777,216 colours 16,777,216 colours

PC Resolution
Maximum 1360 x 768 @ 60Hz 1360 x 768 @ 60Hz
Optimum 1360 x 768 @ 60 Hz 1360 x 768 @ 60 Hz

Input Signal
Sync. H/V Separate, TTL, P. or N. H/V Separate, TTL, P. or N.
V ideo Signal 0.7 Vp-p @ 75 ohm 0.7 Vp-p @ 75 ohm

TV
Colour System PAL, SECAM-B/G, D/K, PAL, SECAM-B/G, D/K,
I, I/I, L/L’, NTPB (AV3.58, 4.43) I, I/I, L/L’, NTPB (AV3.58, 4.43)
Sound System BG, DK, I, L BG, DK, I, L

V ideo
Colour System PAL/NTSC/SECAM PAL/NTSC/SECAM
Video System CVBS, S-VHS, RGB CVBS, S-VHS, RGB

SCART 1
Video Input/Output 1.0 Vp-p @ 75 ohm 1.0 Vp-p @ 75 ohm
RGB Input 0.7 Vp-p @ 75 ohm 0.7 Vp-p @ 75 ohm
Audio Input/Output 500mVrms 500mVrms

SCART 2
V ideo Input/Output 1.0 Vp-p @ 75 ohm 1.0 Vp-p @ 75 ohm
Audio Input/Output 500mVrms 500mVrms

Power Supply
Input AC 100 ~ 240 V, 50 Hz ±3Hz  AC 100 ~ 240 V, 50 Hz ±3Hz

Power Consumption
Normal 170 W 275 W
Power Saving 
						

							
English-65

Technical and Environmental Specifications
Display Mode (PC)

Both screen position and size will vary depending on the type of PC moni\
tor and its resolution.
The table below shows all of the display modes that are supported:

Mode Resolution Horizontal Vertical Pixel Clock Sync Polarity
Frequency (kHz) Frequency (Hz) Frequency (MHz) (H/V)
IBM
640 x 480 31.469 59.940 25.175 - / -
720 x 400 31.469 70.087 28.322 - / +

VESA
640 x 480 37.861 72.809 31.500 - / -
640 x 480 37.500 75.000 31.500 - / -
800 x 600 37.879 60.317 40.000 + / +
800 x 600 48.077 72.188 50.000 + / +
800 x 600 46.875 75.000 49.500 + / +
1024 x 768 48.364 60.000 65.000 - / -
1024 x 768 56.476 70.069 75.000 - / -
1024 x 768 60.023 75.029 78.750 + / +
1360 x 768 47.712 60.015 85.800 + / +
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selec\
ted.
DVI dose not support PC function.

Stand Swivel (Left and Right)

-15° ~ 15°

LE32M6 LE32M61BS LE40M6 LE40M61BS
No Yes No Yes
ModelLE32M6/LE32M61BS LE40M6/LE40M61BS
W eight
With stand 19.2 kg (42.33 lbs) 27.5 kg (60.63 lbs)

Environmental Considerations
Operating Temperature 10°C to 40°C (50°F to 104°F) 10°C to 40°C (50°F to 104°F)
Operating Humidity 10% to 80%, non-condensing 10% to 80%, non-condensing
Storage Temperature -20°C to 45°C (-4°F to 113°F) -20°C to 45°C (-4°F to 113°F)
Storage Humidity 5% to 95%, non-condensing 5% to 95%, non-condensing

Audio Characteristics
Audio InputRCA Jack (L, R), 0.5Vrms (-9dB) RCA Jack (L, R), 0.5Vrms (-9dB)Audio Input (PC)3.5Ø Stereo Jack, 0.5Vrms (-9dB) 3.5Ø Stereo Jack, 0.5Vrms (-9dB)Headphone Output Max. 10mW Output  Max. 10mW Output 
(3.5Ø Stereo Jack, 32Ω) (3.5Ø Stereo Jack, 32Ω)
Frequency RF: 80Hz ~ 15kHz (at -3dB) RF: 80Hz ~ 15kHz (at -3dB)
Response A/V: 80Hz ~ 20kHz (at -3dB) A/V: 80Hz ~ 20kHz (at -3dB)

Sound
Output 10 W X 2 10 W X 2
3D Surround SRS TruSurroundXT SRS TruSurroundXT
Stereo Nicam/A3 Nicam/A2

02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 65
 
						

							
English-66

Pin Configurations

SCART Connector

Pin Signal

1Audio output R
2 Audio input R
3 Audio output L
4 Audio chassis return
5V ideo chassis return (RGB blue)
6 Audio input L
7 RGB blue input
8 Switching voltage
9V ideo chassis return (RGB green)
10 AV-Link (Ext 1) 11 RGB green input

Pin Signal

12 -
13 Video chassis return (RGB red)
14 -
15 RGB red input
16 Blanking signal (RGB switching)
17 Video chassis return
18 Blanking signal ground
19 Video output
20 Video input
21 Screening/chassis return

PC Input Connector (15Pin)

Pin Signal

1Red (R)
2 Green (G)
3 Blue (B)
4 Grounding
5 Grounding (DDC)
6 Red (R) Grounding
7 Green (G) Grounding
8 Blue (B) Grounding

Pin Signal

9Reserved
10 Sync Grounding 11 Grounding
12 Data (DDC)
13 Horizontal sync.
14 Vertical sync.
15 Clock (DDC)

02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 66
 
						

							
This page is intentionallyleft blank.

02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 67
 
						

							
02 BN68-00956D-04Eng.qxd  11/29/05  4:19 PM  Page 68