Samsung Ht Ds100 Instruction Manual

							PREPARATION
10
Subwoofer
Subwoofer Level
control
Crossover frequency
control
DIN Audio Input terminal 
Speaker Output Terminals 
Subwoofer Power button
< Front > < Right >
< Rear >< Rear >
Subwoofer Level control
Subwoofer Power button
DIN Audio Input terminal 
Crossover frequency control
Speaker Output Terminals 
PSWS1000T (Subwoofer of HT-DS1000)
PSWS1100T (Subwoofer of HT-DS1100)
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 13
 
						

							11
Description
TVDVD RECEIVER
OPEN/CLOSE
DVD TUNER AUX
EZ VIEW
NTSC/PALSLOW SUB TITLE ASC
TUNING/CH
PL II
RETURN
M
EN
UINFO
MUTE
MODE
ENTER
SOUND EDITTEST TONE
SLEEP
LOGO REPEATCANCEL ZOOM
REMAIN
TUNER 
MEMORY
DCDi
PL II
EFFECT
VOLUMELSM
V-H/PMOVIE MUSIC SUPER5.1MO/ST TV/VIDEO
MODEDIMMER
RDS DISPLAY
PTY– PTY+PTY SEARCHTA
PL II MODE button
VOLUME button
MENU button TV, DVD POWER button
OPEN/CLOSE button
SUPER 5.1 button
Live Surround Mode button/
Virtual Headphone button Auto Sound Calibration button
RETURN button
Number(0~9) buttons  RDS Selection button
SLEEP button
EZ VIEW, NTSC/PAL buttonLOGO COPY buttonTV indicator 
DVD RECEIVER indicator 
TV/VIDEO, DIMMER buttonMODE button
Direction/Enter button 
REPEAT button REMAIN button CANCEL button ZOOM button TUNER MEMORY, DCDi button SOUND EDIT button TEST TONE button MUTE button INFO button TUNING/CH button MOVIE button SLOW, MO/ST button SUBTITLE button
PL II EFFECT button
—Remote Control—
DVD button 
Play/Pause button
Tuning Preset/CD Skip button
Stop button  AUX button 
TUNER button 
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 14
 
						

							To open the remote control cover, push the
top of the cover, then slide downward.
12
Insert Remote Batteries
The remote control can be used up to approximately 23
feet/7 meters in a straight line. It can also be operated at
a horizontal angle of up to 30° from the remote control
sensor.
Range of Operation of the Remote Control 
Remove the battery
cover on the back
of the remote by
pressing down and
sliding the cover in
the direction of the
arrow.1Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).2Replace the battery
cover.3
Follow these precautions to avoid leaking or cracking batteries:
•Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
•Use the correct type of batteries.Batteries that look similar may differ in voltage.
•Always replace both batteries at the same time.
•Do not expose batteries to heat or flame.
Caution
PREPARATION
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 15
 
						

							13
Installing DVD player 
You can select and install either the Vertical or Horizontal Stand, depending on your preference.
REAR OF
VERTICAL STAND REAR OF MAIN UNIT Main unit
Main unitVertical Stand
Horizontal Stand Round support
Vertical Stand (supplied)
2
1
Fix the round support and Vertical
Stand with screws 3EA.
3
Locate the two indentations on the bottom
of the Main unit. Slide the Main unit onto
the two matching dowels on Vertical Stand.
4
Fix the Vertical Stand and the main
unit with screws 4EA. Open the cover on the rear of Vertical
Stand and connect the Audio/Video
cable into the Vertical Stand.
(See pages 19~24 for how to connect the cable.)
Horizontal Stand (supplied)
2
1
Locate the two indentations on the side
of the main unit and slide onto the two
matching dowels on Horizontal Stand.
Fix the Horizontal Stand and the
main unit with screws 2EA.
1
4
2
3
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 16
 
						

							14
CONNECTIONS
RSLS
C
LSWR
Rear Speakers
•Place these speakers behind your listening position.
•If there isnt enough room, place these speakers to face each other.
•Place them about 60 to 90cm (2 to 3feet) above your ear, facing
slightly downward.
*Unlike the front and center speakers, the rear speakers are used
to handle mainly sound effects and sound will not come from
them all the time.
Subwoofer
•The position of the subwoofer is not so critical. 
Place it anywhere you like.
•Usually, it is placed by a corner near the front speakers.
Front Speakers  
•Place these speakers in front of your listening
position, facing inwards (about 45°) toward you.
•Place the speakers so that their tweeters will be at
the same height as your ear.
•Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speakers.
Center Speaker
•It is best to install it at the same height as the front
speakers.
•You can also install it directly over or under the TV.
Position of the DVD Player
•Place it on a stand or cabinet shelf, or under
the TV stand.
Selecting the Listening Position
The listening position should be located about 2.5 to 3
times the distance of the TVs screen size away from the
TV. Example: For 32 TVs 2~2.4m (6~8 feet)
For 55 TVs 3.5~4m (11~13 feet)
Connecting the Speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
RL
C
RSLS
SW
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 17
 
						

							15
Connecting the Speakers
Connect the front, rear and center speakers to the speaker output jack on the side of subwoofer.
Bottom of Main unit
(HT-DS1000)Rear of Subwoofer (PSWS1000E)
Center Speaker
Green
Gray
RedBlue
White
Rear Speaker (L)  Rear Speaker (R) 
Front Speaker (L) Front Speaker (R) 
Subwoofer: The subwoofer is active,  with a built-in a  150W amplifier,  and
outputs rich bass through 8 inch speaker units. You can listen to
the optimal LFE (bass) by using the subwoofer-only volume
control and the variable crossover control.
• 
The control is calibrated from –6dB (minimum) to +6dB (maximum).
Crossover: The Crossover sets the cutoff frequency for the subwoofer. Set the
Crossover control for the best bass response  in your room.
• You can adjust the bass or treble output from the front, rear,
center speakers and the subwoofer.
• To the left increases the bass and to the right, treble.
Connecting Main Unit to Subwoofer 
Subwoofer Function 
Use the supplied DIN audio connection cable to connect DIN
Audio Out on the main unit to DIN Audio Input on the
subwoofer.
Press the subwoofer power button on the subwoofer to turn
on the power.1
2
HT-DS1000
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 18
 
						

							Bottom of Main unit
(HT-DS1100)Rear of Subwoofer (PSWS1100E)
Center Speaker
Rear Speaker (L)  Rear Speaker (R) 
Front Speaker (L) Front Speaker (R) 
16
CONNECTIONS
HT-DS1100
Green
Blue
White RedGray
Connecting the Speakers
Black
Press down the terminal
tab on the back of the
speaker.1Insert the black wire into the
black terminal (–) and the gray
wire into the gray (+) terminal,
and then release the tab.2Connect the correct color speaker cable
to the same color speaker output terminal
on the rear of the subwoofer, according
to the polarity markings (+/–).
Example: Connect the green center speaker cable
to the green center speaker output
terminal on the rear of the subwoofer
according to the polarity markings (+/–).
3
Gray
•Do not let children play with or near the speakers. 
They could get hurt if a speaker falls.
•When connecting the speaker wires to the speakers,
make sure that the polarity (+/–) is correct.
•Never touch the speaker terminal while the power is on.
Doing so may result in a risk of electric shock.
Caution
•If you place a speaker near your TV set,
screen color may be distorted because of
the magnetic field generated by the
speaker. If this occurs, place the speaker
away from your TV set.
Note
or
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 19
 
						

							Better Quality
Good Quality
Connecting the Video Out to TV
17
The Component input may be marked ‘DVD input’
depending on the TV. 
•If the TV only supports a resolution of 576i(480i), the screen may be divided into 2 screens, or
display nothing.Note
Connect if the TV component input supports the resolution of over 576p(480p).
Connect the Video Out to the Video
In on the TV.1
Set the Video Input source on your TV
to the corresponding Video output on
your Home Theater.2
Method1When you connect to Video Out
Connect the component output (PR,
P
B, Y) to the component input on the
TV (P
R, PB, Y).
•Be sure to make the correct connections between the
when you connect the component output jacks to the
TV. If these are connected wrong, the screen may show
red or blue, or there may be no screen at all.
1
Set the Video Input source on your TV
to the corresponding Component
output on your Home Theater.2
Method 2 When you connect to Component Out 
Video Cable
(supplied)
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 20
 
						

							Best Quality
18
CONNECTIONS
Connect if the TV has an HDMI (or DVI) In jack.
Connect the HDMI Out to the HDMI 
(or DVI) Input on the TV. 1
Set the Video Input source on your TV
to the corresponding HDMI output on
your Home Theater.2
Method 3When you connect to HDMI Out
• If you connect the HDMI and Component outputs (PR, PB, Y) at the same time, the Component output
resolution changes automatically to the designated HDMI resolution.
Example: If the TV connected to HDMI can only support up to 576p(480p), the HDMI and Component outputs
are all converted to 576p(480p), even if you select the resolution switch to 1080i.
• Since this product has an embedded Video Upscaler function with Faroudja DCDi technology, it can enhance a
576i(480i) DVD resolution output to 576p(480p)/720p/1080i. 
• You do not have to make separate adjustments, since the Home Theater and TV will be automatically adjust
themselves to the optimal resolution and aspect ratio if connected to HDMI. (If the TV is an HDTV and has an
HDMI Input jack, output is automatically converted to the resolution of 1080i.)
• Audio will not be output if decoder is not embedded in TV during 5.1 channel disk playback.
• Component output will give video in ‘576p(480p)’ mode only during DVD disc playback applied with
Macrovision.
• Macrovision processes scramble on analog output to prevent illegal recording. Accordingly, if you are using
HDMI only, it can output 576p(480p)/720P/1080i, but is limited to 576p(480p) only if you are using component. 
• When both HDMI connector and COMPONENT connector are connected, COMPONENT video is not
displayed.
• See your TV owners manual for more information on how to select the TVs Video Input source.
Note
What is HDMI (High Definition Multimedia Interface)?
This device transmits DVD video and audio signals digitally without the process of
converting to analog. You can get sharper digital pictures by connecting the video to
the TV using an HDMI connection cable. 
HDMI Cable
(supplied)HDMI/DVI Cable
(supplied) or
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 21
 
						

							Connecting the Video Out to TV
You can adjust the resolution switch to set the HDMI and component (PR, PB, Y) output resolution to
576p(480p)/720p/1080i.
Example: If the TV supports resolution up to 576p(480p) 
•If you connect the HDMI and Component outputs (PR, PB, Y) at the same
time, Component output resolution changes automatically to the
designated HDMI resolution. 
Caution
Selecting Resolution
Set the resolution switch to 576p(480p).
•A576p(480p) video signal is output through the HDMI and component outputs (PR, PB, Y).
1
• If copy protection is in place, output resolution is automatically converted to 576p(480p) when you play the
DVD, even if you set the resolution to 720p or 1080i.
Note
19
 1p~44p(DS1000)-GB  9/16/04 9:14 AM  Page 22