Samsung HL-R4667W DLP TV User Manual

PC Display
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 121 

PC Display
English - 122
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be 
different, depending on the model.
Connecting a PC (15p D-SUB) to the TV
1
Connect a PC cable between
the PC Output jack on the 
PC and the RGB input jack 
(PC IN) on the TV.
2
Connect a Audio cable
between the Audio jack on 
the PC and the Audio input 
jacks (PC AUDIO IN) on 
the TV.
15Pin (D-Sub)
Cable
PCAudio...

English - 123
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop, 
then click...

PC Display
English - 124
NOTES
•The PC text quality is optimum in XGA mode (1024 x 768@60Hz).
•Both screen position and size will vary, depending on the type of PC monitor and its resolution. 
The table above shows all of the display modes that are supported:
*The interlace mode is not supported.
*The TV will operate abnormally if a non-standard video format is selected.
•When this TV is used as a PC display, 32-bit color is supported (over 16 million colors).
•Your PC display screen might appear...

English - 125
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.
1Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to...

PC Display
English - 126
Changing the Picture Position
After connecting the TV to your PC, adjust the position of picture if it is not well-aligned.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Position”, then press
the ENTER button.
5
Adjust the position of picture
by pressing the …/†/œ/√
button.
Press the EXIT...

1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Auto Adjustment”,
then press the ENTER button.
The picture quality and
position are automatically
adjusted, and the picture
returns to original view
about a few seconds later.
Press the EXIT button to exit.
English - 127
Setup
Language :...

PC Display
English - 128
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Picture”, then press
the ENTER button.
Press the …or †button to
select “Size”, then press the
ENTER button.
3
Press the œor √button to
select the screen format you
want, then press the ENTER
button.
Press the EXIT button to exit.
NOTES
•The “WidePC” and “4:3”...

English - 129
Viewing the Current Resolution
You can get the resolution information of your PC.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
The resolution information
is displayed on the screen.
NOTE
•To change the resolution, see pages 123~124.
Setup
Language : English√Time√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√Color...

PC Display
English - 130
Initializing the Picture Settings
You can replace all picture settings with the factory default values.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Image Reset”, then
press the ENTER button.
The picture settings are
replaced with the factory
default values.
Press the EXIT button to...