Samsung HL-R4667W DLP TV User Manual

English - 111
Follow the instructions below to activate D-Net in the menu.
1
Press the MENU button. 
Press the ENTER button to select “Input”.
2
Press the …or †button to select 
“D-Net”, then press the ENTER button.
3
Press the …or †button to select a 
D-Net (IEEE1394) connected device. •The TV and all other devices,
connected on the D-Net (IEEE1394)
chain, appear in the D-Net device list.
Input
Source List : TV√Edit Name√Anynet
D-Net
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Input...

Using the D-Net
English - 112
The D-Net control panel
Select an IEEE1394 from the D-Net device list. The TV will then display the D-Net control panel. 
This panel allows you to use the TV remote control to control the selected IEEE1394 device.
1
Press the D-Net button on the remote control.
2
Press the …or †button to select a 
D-Net (IEEE1394) connected device. 
Press the ENTER button.
3
Use the …, †, œ, √buttons on the remote 
control to move through the options (see next 
page) available in the D-Net...

English - 113
NOTES
•Press the …, †, œ, √buttons on the remote control to select a control panel button and press the
ENTER button on the remote control.
•Depending on the device being controlled, not all options on the D-Net control panel may be available.
•The selected IEEE1394 device and its functions can be controlled through the equivalent buttons on the
TV’s remote control.
•Not all functions are supported for all IEEE1394 devices.
•It is possible to use direct hot keys on the remote control...

Operating Tips
1) When the screen is switched to the TV program. 
- When you select the first button, the TV button, in the Device List, it switches to the TV program. 
- Although you have selected another device from the Device List, if detecting a video signal from 
the device fails, the “Connection failed” message appears and the screen automatically switches 
to the TV program.
- When the 1394 connection to the selected device is disconnected, the screen automatically 
switches to the TV program. In...

English - 115
10)  When multiple devices are connected, some devices may appear and then disappear periodically 
in the Device List. This is because some devices malfunction when multiple devices are connected.
In this case, you have to discover and remove the defective device from the connection by 
removing the devices one by one. 
11)  When multiple devices are connected, the response time may be relatively long when selecting a 
device. This may happen when there is a device(s) that malfunctions and...

Using the D-Net
English - 116
Possible Solution
Only DTVs, STBs, AVHDDs, DVHSs and MPEG 
camcorder IEEE 1394 devices are controllable.
Other devices will display “UNCONTROLLABLE” in
the device list. 
Some supported devices may display as
“UNCONTROLLABLE” due to an initialization error.
➔If a device is supported but is displayed as 
“UNCONTROLLABLE”, reconnect the 1394 cable.
If this does not work, this is because the 
information about the device is unreadable due 
to an internal error.
Since a device,...

English - 117
Possible Solution
This message appears when the connection speed of
the connected device and the device selected from the
Target List are different when copying data.
➔Connect a low speed device between the two 
devices. (See figure)
A 1394 device has a maximum connection 
speed which will be marked near the 
IEEE 1394 connector with an “S” number 
(i.e., S100,S200,S400). The higher the number, 
the faster the maximum connection speed. 
This TV has a maximum connection speed of S400.
This...

Using the D-Net
English - 118
Possible Solution
Check if the current mode for DTV and STB is set to
analog by mistake. For AVHDD, check if the played
content reaches to the end. (Select the item from 
the content list again.) For DVHS, check if a D-VHS
tape is being used. If the camcorder supports the 
DV format, no picture will be displayed on the screen.
This message appears when the D-Net function is
being initialized.
Retry after a short wait to use the D-Net function.
This message appears when the...

English - 119
Possible Solution
This message appears if you have connected a 
1394 device or equipment other than a supported
device (DVHS, DTV, STB, AVHDD, Camcorder), or if
the connected device does not support the AVC
defined in the 1394 specifications, even if the device
is a supported device, when you have selected the
device to use it.
This message appears if there is a connection problem
when trying to use a D-Net device. 
This message appears if the AVHDD is booting when
trying to use the AVHDD....

SAMSUNG
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 120