Samsung HL-R4667W DLP TV User Manual

							PC Display
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 121 
						

							PC Display
English - 122
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be 
different, depending on the model.
Connecting a PC (15p D-SUB) to the TV
1
Connect a PC cable between
the PC Output jack on the 
PC and the RGB input jack 
(PC IN) on the TV.
2
Connect a Audio cable
between the Audio jack on 
the PC and the Audio input 
jacks (PC AUDIO IN) on 
the TV.
15Pin (D-Sub)
Cable
PCAudio Cable TV Rear Panel
BP68-00469A-00(118~135)  2/24/05  11:52 AM  Page 122 
						

							English - 123
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop, 
then click on Properties. The Display Dialog-Box 
will be displayed.
continued... 2Click on Settings, then set the Display Mode with
reference to the Display Modes Table. You do not
need to change the Colors settings.
3Click on Advanced. A new settings dialog box
will be displayed.
4Click on the Monitor tab, then set the Screen
Refresh Rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal
Frequency individually if you can do so instead 
of setting the Screen Refresh Rate.
5Press the OK button, close the window, then 
press the OK button on the Display Registration
Information window. Automatic re-booting may
commence at this moment.
6Shutdown the PC, and connect it to your TV.
*The actual screens on your PC may look 
different, depending on your particular version 
of Windows and the type of your PC.
*When you use your TV as a PC monitor, 
it supports Colors up to 32 bits.
*In this case, the display on the TV may look 
different depending on your particular version 
of Windows or the PC manufacturer.
*When connecting a PC, you must set it to the 
display settings that are supported by the TV. 
Otherwise, the message Out of input range 
will be displayed.
2
3
4
5
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 123 
						

							PC Display
English - 124
NOTES
•The PC text quality is optimum in XGA mode (1024 x 768@60Hz).
•Both screen position and size will vary, depending on the type of PC monitor and its resolution. 
The table above shows all of the display modes that are supported:
*The interlace mode is not supported.
*The TV will operate abnormally if a non-standard video format is selected.
•When this TV is used as a PC display, 32-bit color is supported (over 16 million colors).
•Your PC display screen might appear different, depending on the manufacturer (and depending on
your particular version of Windows). Check your PC instruction book for information about connect-
ing your PC to a TV display-monitor.
•Same modes as PC are supported for the signal input to the DVI jack. Only a separate sync 
signal is supported. 
Resolution
640 x 350
720 x 400
640 x 480
800 x 600
1024 x 768
1920 x 1080i
1280 x 720p
720 x 483pHorizontal Frequency [KHz]
31.47
31.47
31.47
35.00
37.86
37.50
35.16
37.88
48.08
46.87
53.67
48.36
56.40
60.02
33.75
45.00
31.47Vertical Frequency [Hz]
70.00
70.00
60.00
66.70
72.80
75.00
56.30
60.30
72.20
75.00
85.10
60.00
70.10
75.00
60
60
60Pixel Clock [MHz]
25.175
28.322
25.175
30.24
31.50
31.50
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
74.25
74.25
27Sync Polarity (H/V)
+/-
-
/-
-
/+
-/-
-
/-
-
/-
-
+/-
+/+-
+/+
+/+
+/+
-/-
-
/-
+/-
X
X
X
Mode
VGA
SVGA
XGA
DTV
Display Modes
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 124 
						

							English - 125
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.
1Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Image Lock”, then
press the ENTER button.
5
Press the …or †button to
select “Coarse” or “Fine”,
then press the ENTER button.
6
Pressing the œor √button
to remove the picture noise.
Press the EXIT button to exit.▲Coarse▼800
▲Fine▼0
NOTE
•This feature may change
the width of the image.
If necessary, adjust the
position to center.
Setup
Language : English√Time√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√Color Weakness√▼ More
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Setup
▲ MorePC√Port Selection: G-Link√Function Help: Off√CableCARDTM√CableCARDTMSetup√
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
PC
Image Lock√Position√Auto Adjustment
Image Reset
Resolution       : 1024 x 768, 60Hz
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Image Lock
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Coarse 800
Fine 0
•You can also select
these options (Coarse,
or Fine) by pressing the
…or †button.
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 125 
						

							PC Display
English - 126
Changing the Picture Position
After connecting the TV to your PC, adjust the position of picture if it is not well-aligned.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Position”, then press
the ENTER button.
5
Adjust the position of picture
by pressing the …/†/œ/√
button.
Press the EXIT button to exit.
Setup
Language : English√Time√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√Color Weakness√▼ More
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Setup
▲ MorePC√Port Selection: G-Link√Function Help: Off√CableCARDTM√CableCARDTMSetup√
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
PC
Image Lock√Position√Auto Adjustment
Image Reset
Resolution       : 1024 x 768, 60Hz
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Position
Input
Picture
Sound
Channel
Setup
Listings
AdjustEnterReturn
▲
▼
▼▼
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 126 
						

							1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Auto Adjustment”,
then press the ENTER button.
The picture quality and
position are automatically
adjusted, and the picture
returns to original view
about a few seconds later.
Press the EXIT button to exit.
English - 127
Setup
Language : English√Time√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√Color Weakness√▼ More
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Setup
▲ MorePC√Port Selection: G-Link√Function Help: Off√CableCARDTM√CableCARDTMSetup√
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
PC
Image Lock√Position√Auto Adjustment
Image Reset
Resolution       : 1024 x 768, 60Hz
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Adjusting the Picture Quality and Position Automatically
This feature allows the TV to self-adjust to the incoming video signal. The values of fine, coarse and
position are adjusted automatically.
Auto Adjustment in Progress
Please Wait.i
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 127 
						

							PC Display
English - 128
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Picture”, then press
the ENTER button.
Press the …or †button to
select “Size”, then press the
ENTER button.
3
Press the œor √button to
select the screen format you
want, then press the ENTER
button.
Press the EXIT button to exit.
NOTES
•The “WidePC” and “4:3” modes are recommended for the 
PC mode.
•In VGA (640x480) and SVGA (800x600) modes, the “WideTV”
and “4:3” modes are available.
•In XGA (1024x768) mode, the “WideTV” mode is available.
•“WideTV”: Scales the picture to the size of the TV screen 
regardless of the aspect ratio of the input source.
•“4:3”: Displays the picture as it is without changing the aspect
ratio of input source.
•“WidePC”: Scales the picture to 92% of the TV screen, 
regardless of the aspect ratio of the input source. The picture 
position (     ,     ) and size (     ) adjustment are available by
pressing the …/†/œ/√button.
Alternate method
Press the P.SIZE button on the
remote control repeatedly to
change the picture Size.Picture Size
16:9 ➝ 4:3
WideTV ➝ WidePC
WideTV ➝ WidePC ➝ 4:3
16:9 ➝ Zoom1➝ Zoom2 ➝ 4:3
16:9 ➝ Panorama ➝ Zoom1➝ Zoom2 ➝ 4:3 Source (PC/HDMI)
1920 x 1080i
1280 x 720
1024 x 768
720 x 483 (480p)
Others
Picture
Mode : Standard√Size : WidePC√Digital NR : On√DNIe Demo : Off√My Color Control√Film Mode : Off√PIP√
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Size
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
WideTVWidePC 4:3
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 128 
						

							English - 129
Viewing the Current Resolution
You can get the resolution information of your PC.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
The resolution information
is displayed on the screen.
NOTE
•To change the resolution, see pages 123~124.
Setup
Language : English√Time√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√Color Weakness√▼ More
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Setup
▲ MorePC√Port Selection: G-Link√Function Help: Off√CableCARDTM√CableCARDTMSetup√
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
PC
Image Lock√Position√Auto Adjustment
Image Reset
Resolution       : 1024 x 768, 60Hz
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 129 
						

							PC Display
English - 130
Initializing the Picture Settings
You can replace all picture settings with the factory default values.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Image Reset”, then
press the ENTER button.
The picture settings are
replaced with the factory
default values.
Press the EXIT button to exit.
Setup
Language : English√Time√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√Color Weakness√▼ More
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Setup
▲ MorePC√Port Selection: G-Link√Function Help: Off√CableCARDTM√CableCARDTMSetup√
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
PC
Image Lock√Position√Auto Adjustment
Image Reset
Resolution       : 1024 x 768, 60Hz
MoveEnterReturn Input
Picture
Sound
Channel
Setup
Listings
Image Reset is completed.i
BP68-00469A-00(118~135)  2/24/05  10:11 AM  Page 130