Samsung CLP 660ND User Manual

							
4.2   
Specifications on print media
Ty p eSizeDimensionsWeighta
a. If media weight is over 105 g/m2 (28 lb bond), use the multi-purpose tray.
Capacityb
b. Maximum capacity may differ depending on media we ight, thickness, and environmental conditions.
Plain paper Letter 216 x 279 mm (8.5 x 11 inches) • 60 to 105 g/m2 (16 to 28 lb 
bond) for the tray
• 60 to 163 g/m
2 (16 to 43 lb 
bond) for the multi-purpose 
tray • 250 sheets of 75 g/m
2 
(20 lb bond) paper for the 
tray
• 100 sheets of 75 g/m
2 
(20 lb bond) in the multi-
purpose tray
• 500 sheets of 75 g/m
2 
(20 lb bond) paper for 
optional tray
Legal 216 x 356 mm (8.5 x 14 inches)
Folio 216 x 330 mm (8.5 x 13 inches)
A4 210 x 297 mm (8.26 x 11.69 inches)
Oficio 216 x 343 mm (8.5 x 13.5 inches)
JIS B5 182 x 257 mm (7.16 x 10.11 inches)
ISO B5 176 x 250 mm (6.93 x 9.84 inches) 
Executive 184 x 267 mm (7.25 x 10.5 inches)
A5 148 x 210 mm (5.82 x 8.26 inches) • 60 to 105 g/m
2 (16 to 28 lb 
bond) for the tray
• 60 to 163 g/m
2 (16 to 43 lb 
bond) for the multi-purpose 
tray • 150 sheets of 75 g/m
2 
(20 lb bond) paper for the 
tray
• 100 sheets of 75 g/m
2 
(20 lb bond) in the multi-
purpose tray
Statement 140 x 216 mm (5.5 x 8.5 inches)
A6 105 x 148 mm (4.13 x 5.82 inches)
Envelope Envelope Monarch 98 x 191 mm (3.87 x 7.5 inches) 75 to 105 g/m
2 (20 to 28 lb 
bond) 10 sheets of 75 g/m2 (20 lb 
bond) in the multi-purpose 
tray
Envelope No. 9 98 x 225 mm (3.87 x 8.87 inches)
Envelope No. 10 105 x 241 mm (4.12 x 9.5 inches)
Envelope DL 110 x 220 mm (4.33 x 8.66 inches)
Envelope C5 162 x 229 mm (6.37 x 9.01 inches)
Envelope C6 114 x 162 mm (4.48 x 6.38 inches)
Envelope 6 3/4 92 x 165 mm (3.62 x 6.5 inches)
Labels Letter, Legal, Folio,  A4, JIS B5, ISO B5, 
Executive, A5, A6, 
Oficio, Statement Refer to the Plain paper section 120 to 150 g/m
2 (32 to 40 lb 
bond) 10 sheets of 75 g/m2 (20 lb 
bond) paper for the multi-
purpose tray
Card stock Letter, Legal, Folio,  A4, JIS B5, ISO B5, 
Executive, A5, A6, 
Oficio, Statement Refer to the Plain paper section 90 to 163 g/m
2 (24 to 43 lb 
bond) 10 sheets of 75 g/m2 (20 lb 
bond) paper for the multi-
purpose tray
Minimum size (custom) 76 x 127 mm (3 x 5 inches) 60 to 163 g/m
2 (16 to43 lb bond) 
Maximum size (custom) 216 x 356 mm (8.5 x 14 inches)
Downloaded From ManualsPrinter.com Manuals 
						

							
4.3   
Media sizes supported in each mode
Guidelines for special print media
ModeSizeWeightSource
Single side 
printing All sizes 
supported by 
the machineAll weights 
supported by 
the machine •tray1
• optional tray
• multi-purpose tray
Duplex 
printing
a
a. 75 to 105 g/m2 (20 ~ 28 lb bond) only, and this feature is supported in 
CLP-6xxND.
Letter, A4, 
Legal, Folio, 
Oficio 75 to 90 g/m2 
(20 to 24 lb 
bond) •tray1
• optional tray
• multi-purpose tray
Media typeGuidelines
Envelopes • Successful printing on envelopes depends upon  the quality of the envelopes. When selecting 
envelopes, consider the following factors:
-  Weight: The weight of the envelope paper should not exceed 90 g/m
2 or jamming may 
occur.
-  Construction: Prior to printing, envelopes  should lie flat with less than 6 mm curl, and 
should not contain air.
-  Condition: Envelopes should not be wrinkled,  nicked, or otherwise damaged.
-  Temperature: You should use envelopes that  are compatible with the heat and pressure of 
the machine during operation.
• Use only well-constructed envelopes with sharp 
and well creased folds.
• Do not use stamped envelopes.
• Do not use envelopes with clasps, snaps,  windows, coated lining, se lf-adhesive seals, or 
other synthetic materials.
• Do not use damaged or poorly made envelopes.
• Be sure the seam at both ends of the envelope 
extends all the way to the corner of the 
envelope.
Acceptable
Unacceptable
• Envelopes with a peel-off adhesive strip or with  more than one flap that folds over to seal must 
use adhesives compatible with the machine’s 
fusing temperature for  0.1 second. Check your 
machine’s specification to view the fusing 
temperature, see page 10.1. The extra flaps and 
strips might cause wrinkling, creasing, or jams, 
and may even damage the fuser.
• For the best print quality, position margins no 
closer than 15 mm from the edges of the 
envelope.
• Avoid printing over the area where the 
envelope’s seams meet.
Labels • To avoid damaging the machine, use only labels  designed for use in laser machines.
• When selecting labels, consider the following 
factors:
-  Adhesives: The adhesive material should be stable at your machine’s fusing temperature. 
Check your machine’s specification to view the 
fusing temperature, see page 10.1.
-  Arrangement: Only use labels with no  exposed backing between them. Labels can 
peel off sheets that have spaces between the 
labels, causing serious jams.
-  Curl: Prior to printing, labels must lie flat with  no more than 13 mm of curl in any direction.
-  Condition: Do not use labels with wrinkles,  bubbles, or other indications of separation.
• Make sure that there is no exposed adhesive 
material between labels. Exposed areas can 
cause labels to peel off during printing, which 
can cause paper jams. Exposed adhesive can 
also cause damage to machine components.
• Do not run a sheet of labels through the machine  more than once. The adhesive backing is 
designed for only a single pass through the 
machine.
• Do not use labels that are separating from the 
backing sheet or are wrinkled, bubbled, or 
otherwise damaged.
Card stock or 
custom-sized 
materials • Do not print on media smaller than 76 mm wide 
or 356 mm long.
• In the software application, set margins at least  6.4 mm away from the edges of the material.
Media typeGuidelines
Downloaded From ManualsPrinter.com Manuals 
						

							
4.4   
Caution  
Using photographic paper or coated paper may cause 
problems, requiring repairs. Su ch repairs are not covered by 
Samsung’s warranty or service agreements.
Preprinted 
paper
• Letterhead must be printed with heat-resistant 
ink that will not melt, vaporize, or release 
hazardous emissions when subjected to the 
printer’s fusing temperature for 0.1 second. 
Check your machine’s specification to view the 
fusing temperature, see page 10.1.
• Letterhead ink must be non-flammable and  should not adversely affect printer rollers.
• Forms and letterhead should be sealed in a 
moisture-proof wrapping to prevent changes 
during storage.
• Before you load preprinted paper, such as forms 
and letterhead, verify that the ink on the paper is 
dry. During the fusing process, wet ink can come 
off preprinted paper, reducing print quality.
Media typeGuidelinesLoading paper
In the tray
Load the print media you use for the majo rity of your print jobs in tray 1. 
Tray 1 can hold a maximum of 250 sheets of 75 g/m2 (20 lb bond) plain 
paper. 
You can purchase an optional tray and attach it below the standard tray 
to load an additional 500 sheets of paper. (See Accessories on 
page 8.1.)
Loading paper in the tray 1 or optional tray
1 To load paper, pull and open the pa per tray and place paper with the 
side you want to print facing up.
2 After loading paper, set the paper type and size for the tray 1. See 
Software section for PC-printing.
Note
• If you experience problems with paper feed, place one sheet at 
a time in the multi-purpose tray.
• You can load previously printed paper. The printed side should  be facing up with an uncurled edge at the front. If you 
experience problems with paper  feed, turn the paper around. 
Note that print quality is not guaranteed. 
Full
Empty
Downloaded From ManualsPrinter.com Manuals 
						

							
4.5   
Changing the size of the paper in the paper tray
To load longer sizes of paper, such as Legal-sized paper, you need to 
adjust the paper guides to extend the paper tray.
1 Adjust the paper length guide to the desired paper length. It is 
preset to Letter or A4 si ze depending on the country. 
1tray extend lever
2paper length guide
3paper width guide
2After inserting paper into the tray, while pinching the paper width 
guide as shown, move it toward the stack of paper until it lightly 
touches the side of the stack. Do  not press the guide too tightly to 
the edge of the paper; the guide may bend the paper. 
When you use legal-sized paper, yo u need to extend the length of 
the tray.
3 Press and hold the green lever on the back of the tray, when you are 
holding the lever, extend the tray  to the corresponding position. 
4 Load the paper into the tray. 
5 Place the tray into the machine.
6 Set the paper size from your computer. (See page 4.7)
Note
• Do not push the paper width guides far enough to cause the 
materials to warp.
• If you do not adjust the paper width guides, it may cause paper  jams.
tray extend lever
Downloaded From ManualsPrinter.com Manuals 
						

							
4.6   
In the multi-purpose tray
The multi-purpose tray can hold specia l sizes and types of print material, 
such as postcards, note ca rds, and envelopes. It is useful for single page 
printing on letterhead or colored paper.
Tips on using the multi-purpose tray
• Load only one size of print media at a time in the multi-purpose tray.
• To prevent paper jams, do not add paper when there is still paper in  the multi-purpose tray. This also applies to other types of print media.
• Print media should be loaded face down with the top edge going into  the multi-purpose tray first and be  placed in the center of the tray.
• Always load only the specified print media to avoid paper jams and  print quality problems. (See Selecting print media on page 4.1.)
• Flatten any curl on postcards, envelopes, and labels before loading  them into the multi-purpose tray.
To load paper in the multi-purpose tray:
1 Hold the handle of multi-purpose tray and pull it down to open.
2 If you are using paper, flex or fan the edge of the paper stack to 
separate the pages before loading.
3Load the paper.
Note 
If you want to load the used paper which one side has been 
printed already, place the paper with the used side facing 
up.
4 Squeeze the multi-purpose tray pape r width guides and adjust them 
to the width of the paper. Do not  force too much, or the paper will be 
bent, which will result in a paper jam or skew.
Downloaded From ManualsPrinter.com Manuals 
						

							
4.7   
5 After loading paper, set the paper type and size for the multi-
purpose tray. See 
Software section for PC-printing.
Note 
The settings made from the printer driver override the 
settings on the control panel.
6 After printing, close the multi-purpose tray.
Note
Depending on the media type you are using, keep the following 
loading guidelines:
• Envelopes: Place an envelopes flap side up, stamp area 
bottom right.
• Labels: Print side up and top short edge entering the machine  first.
• Preprinted paper: Place the  design side down with top-edge 
toward the machine. 
• Card stock: Print side up a nd the short edge entering the 
machine first.
• Previously printed paper: Previously printed side up with an  uncurled edge toward the machine.
Setting the paper size and type
The settings you change remain in effect only while you are using the 
current program. To make your changes permanent, make them in the 
Printers folder.
Note 
The following procedure is for Windows XP. For other Windows 
OS, refer to the corresponding Windows Users Guide or online 
help.
1 Click the  Start button on the computer screen.
2 Select  Printers and Other Hardwares .
3 Select  Printers and Faxes .
4 Right-click on the printer driver icon and select  Printing 
Preferences .
5 Click the  Paper tab, and change the settings on  Paper Options.
6 Click  OK.
Downloaded From ManualsPrinter.com Manuals 
						

							
5.1   
5 Basic printing
This chapter explains common printing tasks. 
Printing a document
Your machine allows you to print from various Windows, Macintosh, or 
Linux applications. The exact steps fo r printing a document may vary 
depending on the application you use.
1 Open the document you want to print.
2 Select  Print from the  File menu. The Print window is displayed. It 
may look slightly different de pending on your application.
3 Select  your printer driver  from the Selet Printer  drop-down list.
4 To start the print job, click  OK or Print  in the  Print window.
For details about printing, see 
Software section.
Canceling a print job
If the print job is waiting in a prin t queue or print spooler, such as the 
printer group in Windows, delete the job as follows:
1 Click the Windows  Start menu.
2 For Windows 2000, select  Settings and then  Printers.
For Windows XP/2003, select  Printers and Faxes.
For Windows Vista, select  Control Panel > Hardware and Sound  
>  Printers .
3 Double-click the  Samsung CLP-6xx Series  icon. (Or Samsung 
CLP-6xx Series PS )
4 From the  Document  menu, select  Cancel.
Note
You can also access this window by simply double-clicking the 
printer icon at the bottom right corner of the Windows desktop.
You can also cancel the current job by pressing  Stop on the control panel.
Downloaded From ManualsPrinter.com Manuals 
						

							
6.1   
6 Maintenance
This chapter provides information for maintaining your machine and the 
toner cartridge.
This chapter includes:
• Printing a machine configuration report
• Printing a network report
• Monitoring the supplies life
• Cleaning your machine
• Maintaining the cartridge
• Redistributing toner
• Replacing the toner cartridge
• Replacing the paper transfer belt
• Maintenance parts
• Managing your machine from the website
Printing a machine configuration report
You can print the machines information.
1 Press  Menu on the control panel until you see  Information on the 
bottom line of the display. 
2 Press  OK.
3 Press the left/right arrow un til Configuration displays.
4 Press  OK.
5 The display shows  Print?, then press  OK to print the configuration 
report.
Printing a network report
You can print the machines network in formation such as the protocol type 
you set, IP address and so forth.
1 Press  Menu on the control panel until you see  Network on the 
bottom line of the display. 
2 Press  OK.
3 Press the left/right arrow button until  Network Info. displays.
4 Press  OK.
5 The display shows  Print?, then press  OK to print the configuration 
report.
Monitoring the supplies life
If you want to view the supply life indicators, follow the next step.
1 Press  Menu on the control panel until you see System Setup on the 
bottom line of the display. 
2 Press  OK.
3 Press the left/right arrow until  Maintenance displays.
4 Press  OK.
5 Press the left/right arrow until  Supplies Life displays.
6 Press  OK.
7 The display shows two options as you press the left/right arrow 
button. 
• To ta l : displays the total number of pages printed.
•  Toner Remains : displays how much toner remains in the 
cartridge.
8 When you select the option, press  OK to browse the life.
Cleaning your machine
To maintain print quality, follow the cleaning procedures below each time 
the toner cartridge is replaced.
Caution
• Cleaning the machine cabinet with cleaning materials that 
contain large amounts of alco hol, solvent, or other strong 
substances can discolor or damage the cabinet.
• If your machine or its surround ing is contaminated with toner, 
we recommend you to use a cloth or tissue dampened with 
water to clean it. If you use a vacuum cleaner, toner blown 
into the air may be harmful to you. 
Cleaning the outside
Clean the machine cabinet with a soft,  lint-free cloth. You can dampen the 
cloth slightly with water, but be careful not to let any water drip onto or into 
the machine.
Cleaning the inside
During the printing process, paper , toner and dust particles can 
accumulate inside the machine. This buildup can cause print quality 
problems, such as toner specks or smearing. Cleaning the inside of the 
machine clears or reduces these problems. Contact a service 
representative to clean the parts inside the machine.
1 Power off the machine and unplug the power cable.
Downloaded From ManualsPrinter.com Manuals 
						

							
6.2   
2 Using the handle, completely open the front cover.
Caution
• Do not touch the green surface,  the OPC drum or the front of 
the toner cartridge, with your hands or any other material. 
Use the handle on each cartridge in order to avoid touching 
this area.
• Be careful not to scratch the surface of the paper transfer  belt.
• If you leave the front cover open for more than a few minutes,  the OPC drum can be exposed to light. This will cause 
damage to the OPC drum. Cove r the toner cartridge’s OPC 
drum with the some paper could  avoid damaging it from the 
light while you clean the inside.
3 Grasp the handles on the toner cartridge and pull to remove the 
cartridge from the machine.
Caution
If you open the front door, be careful not to touch the 
underneath of the control panel (the lower part of the fuser unit). 
The temperature of the fuser unit might be high and could 
damage your skin.
Note
When you open the front door and work inside the machine, it is 
highly recommend that you remove the paper transfer belt first. 
Because the work you do could  contaminate the paper transfer 
belt.
4 Press the green release handle to release the paper transfer belt. 
Holding the handle on the paper transfer belt, lift it out of the 
machine.
5 Locate the long strip of glass (LSU) inside the cartridge 
compartment, and gently swab the gla ss to see if dirt turns the white 
cotten black.
Downloaded From ManualsPrinter.com Manuals 
						

							
6.3   
6 With a dry lint-free cloth, wipe away any dust and spilled toner from 
the toner cartridges area and their cavities. 
Note
If toner gets on your clothing, wipe it off with a dry
cloth and wash it in cold water. Hot water sets toner into
fabric.
7 Reinstall all the compartments into  the machine, and close the front 
door.
Maintaining the cartridge
toner cartridge storage
To get the most from the toner cartri dge, keep the following guidelines in 
mind:
• Do not remove the toner cartridge fr om its package until ready for use. 
• Do not refill the toner cartridge.  The machine warranty does not cover 
damage caused by using a refilled cartridge.
• Store toner cartridges in the sa me environment as your machine.
• To prevent damage to the toner cartridg e, do not expose it to light for 
more than a few minutes.
Expected cartridge life
The life of the toner cartridge yield depends on the amount of toner that 
print jobs require. The actual number may also be different depending on 
the print density of the pages you pr int on, and the number of pages may 
be affected by operating environment,  printing interval, media type, and 
media size. If you print a lot of graphics, you may need to change the 
cartridge more often.
Redistributing toner
When a toner is low, faded or light areas may appear. It is possible that 
colored images may be printed with incorrect colors due to flawed mixing 
of toner colors when one of the colore d toner cartridges is low on toner. 
You can temporarily improve print q uality by redistributing the toner.
• The toner-related message saying th at the toner is low may appear on 
the display.
• The SmartPanel program window appears on the computer telling you  which color cartridge is low on toner.
1 Using the handle, completely open the front cover.
Caution
• Do not touch the green surface,  the OPC drum or the front of 
the toner cartridge, with your hands or any other material. 
Use the handle on each cartridge in order to avoid touching 
this area.
• Be careful not to scratch the surface of the paper transfer  belt.
• If you leave the front cover open for more than a few minutes,  the OPC drum can be exposed to light. This will cause 
damage to the OPC drum. Close the front cover should the 
installation need to be halted for any reason.
Downloaded From ManualsPrinter.com Manuals