Samsung CLP 550 User Manual

SPECIFICATIONSG.7
G
Paper Specifications
Paper Output Capacity
Paper Input Capacity
CategorySpecifications
Acid Content 5.5 ~ 8.0 pH
Caliper 0.094 ~ 0.18 mm (3.0 ~ 7.0 mils)
Curl in Ream Flat within 5 mm (0.02 in.)
Cut Edge ConditionsCut with sharp blades with no visible 
fray.
Fusing CompatibilityMust not scorch, melt, offset, or release 
hazardous emissions when heated to 
180°C (356°F) for 0.1 second.
Grain Long Grain
Moisture Content 4% ~ 6% by weight
Smoothness 100 ~ 250 Sheffield
Output...

SPECIFICATIONSG.8
Printer and Paper Storage Environment
Paper storage environmental conditions directly affect the feed 
operation.
Ideally, the printer and paper storage environment should be at 
or near room temperature, and not too dry or humid. Remember 
that paper is hygroscopic; it absorbs and loses moisture rapidly.
Heat works with humidity to damage paper. Heat causes the 
moisture in paper to evaporate, while cold causes it to condense 
on the sheets. Heating systems and air conditioners remove...

SPECIFICATIONSG.9
G
Envelopes
Envelope construction is critical. Envelope fold lines can vary 
considerably, not only between manufacturers, but also within a 
box from the same manufacturer. Successful printing on 
envelopes depends upon the quality of the envelopes. When 
selecting envelopes, consider the following components:
• Weight: The weight of the envelope paper should not exceed 
90 g/m
2 (24lb) or jamming may occur.
• Construction: Prior to printing, envelopes should lie flat with 
less than 6...

SPECIFICATIONSG.10
Envelopes with Double Side Seams
Double side-seams envelopes have vertical seams at both ends 
rather than diagonal seams. This style may be more likely to 
wrinkle. Be sure the seam extends all the way to the corner of 
the envelope as illustrated below.
Envelopes with Adhesive Strips or Flaps
Envelopes with a peel-off adhesive strip or with more than one 
flap that folds over to seal must use adhesives compatible with 
the heat and pressure in the printer. The extra flaps and strips...

SPECIFICATIONSG.11
G
Envelope Storage
Proper storage of envelopes helps contribute to print quality. 
Envelopes should be stored flat. If air is trapped in an envelope, 
creating an air bubble, the envelope may wrinkle during 
printing. See “Printing on Envelopes” on page 3.14.
Labels
CAUTIONS: 
• To avoid damaging the printer, use only labels recommended for 
laser printers.
• To prevent serious jams, always use the Multi-purpose Tray to 
print labels and always use the rear output tray.
• Never print...

i
B
booklet printing 5.9
C
cancel, print jobs 4.4
card stock, print 3.21
clean
inside the printer
 6.31
LSU 6.30
outside of the printer 6.29
color mode 4.9, 4.10
components 1.5
configuration page, print 6.2
connect
Ethernet
 F.12
control panel 2.2
buttons 2.3
display 2.2
menus 2.5
custom-sized materials, print 3.21
D
double-sided printing 5.2
E
envelopes, print 3.14
error messages 7.26
Ethernet cable, print F.12
F
Favorite setting, use 4.13
features
printer
 1.2
G
graphic properties, set 4.9
H
help, use...

ii
N
network interface card, install F.8
network printing
card, install
 F.8
locally shared printer, set E.3
network-connected printer, set E.6
parameters, configure E.6
n-up printing 5.6
O
option, install
memory DIMM
 F.2
network interface card F.8
paper tray 2 F.13
optional tray, install F.13
orientation, select 4.6
overlay, use 5.13
P
paper
choose
 3.2
guideline 3.3
load 3.4
sizes and capacities 3.2
specifications G.4
paper jam
in the duplex area
 7.14
in the Multi-Purpose Tray 7.10
in the optional...

iii
S
specification
paper
 G.4
printer G.2
system requirements
for Linux
 C.2
for Macintosh A.2
T
toner cartridge
maintain
 6.4
redistribute 6.5, 6.8
replace 6.8
transfer belt, replace 6.22
transparencies, print 3.17
Tray1, use 3.4
U
uninstall
Linux
 C.7
Remote Control Panel D.4
W
waste toner container, replace 6.11
watermarks, use 5.10
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls