Runco Vx 6c Projector User Manual

OPERATION
USING A MEMORY BANK: You can normally
select a Memory Bank at any time by pressing
(see right). If you want to prevent a Memory
Bank from appearing in this list, you must edit the
Memory Bank as described in Memory Bankslater
in this section. Such a Memory Bank can still be
selected by entering its number as shown at right.
NOTE: 1) The current Memory Bank is highlighted upon entering the Bank List, or, if this
Memory Bank is not displayed in the list, the first Memory Bank in the list is...

OPERATION
Copying or Deleting Memory Banks 
TO COPY A MEMORY BANK, highlight the desired Memory Bank in the Memory Banks
menu, then press          to go to the Memory Bank Copy/Deletesubmenu. Select Copy Current
and press          - a new Memory Bank will be created. It is identical to original, which still
remains, but it is identified with the next available number from 01-99. If you change your mind
and do notwant to copy the current Memory Bank, press         to cancel and return to the previ-
ous...

OPERATION
MEMORY BANK EDIT - STEP 1
Press          to display the main menu. To display the Memory Bank Setupmenu, press      , or
move the highlight to the Memory Bank Setupoption and press        . The Memory Bank Setup
menu will appear.
MEMORY BANK EDIT - STEP 2
To edit parameters shown in the Memory Bank Setup menu, select the relevant channel and press
. The Memory Banksmenu will appear similar to the sample shown below.
Memory Banks Menu (SAMPLE)
MEMORY BANK - STEP 3
If desired, edit the following...

OPERATION
z NEXT BANK: Select this option to see or change Memory Banks settings for the next bank 
in the Memory Banklist.
z LAST BANK: Select this option to see or change Memory Bankssettings for the last bank in the 
Memory Banklist.
3.6 Adjusting the Image
Most options for image adjustments can be accessed through two menus: Scaling Parameters
(                   ) and Image Adjustments(              ), both of which are listed in the Runco Digital
Home Cinemamenu. While in either of these two menus,...

OPERATION
Changes made to the Scaling Parametersmenu are applied immediately and are saved when you
exit the menu (press          or          ).
z H & VScaling: Controls the image widthand heightin tandem, maintaining the orginal 
aspect ratio (proportion) of data from the incoming signal.
z Vertical Scaling:
Vertical scaling adjusts the height the image while keeping the width constant. Use Vertical 
Scaling to display data from the incoming signal in a different aspect ratio. 
z Total H Dots:
(SHORT...

OPERATION
H-Shift
(SHORT CUT: Press          and adjust the top slidebar.)
This option moves picture right and left.
NOTE: The value shown represents where the approximate center of the image lies in relation to
the total number of pixels available horizontally. This varies widely according to the signal-watch
the image while adjusting.
V
-Shift
(SHORT CUT: Press          and adjust the bottom slidebar)
This option moves the picture up and down.
NOTE: The value shown represents where the approximate...

OPERATION
Contrast
(SHORT CUT: Press          and adjust the slidebar.)
Contrast increases or decreases the perceived difference between light and dark areas of your
image (0-100). If contrast is set too high, the light parts of the image lose detail and clarity. If set
too low, the light areas will not be as bright as they could be and it may be difficult to distinguish
between foreground and background information. Adjust so that whites remain bright but not dis-
torted or tinted. For best results,...

OPERATION
3-22
ColorBalance
Select this submenu to work with aspects of color - adjust for saturation and overall hue in video
signals, or adjust gamma or temperature in any signal.
Color
(SHORT CUT: Press          and adjust the slidebar.)
“Color” adjusts color saturation level, or the amount of color in a video image. For 
example, setting Color to “0” produces a black and white image. If Color is set too high,
the color levels in the picture will be over-powering and unrealistic. Use          or...

OPERATION
Gamma Curve
Selected Gamma Curves
THE DEFAULT SETTING OF 2.2 is a normal and smooth gamma curve rec-
ommended for virtually all sources, producing good contrast and smooth gray
transitions without distorting colors.
THE ENHANCED SETTINGelevates middle gray levels compared to
“Default”, and provides a more gradual rolled-off transition to maximum white.
Together, these differences can improve the apprearance of many kinds of
images.  
THE 1.8 SETTINGelevates low gray levels compared to the...

3.7 Adjusting System Parameters and Advanced Controls
Use the Installation, OSD Settingsand Informationmenus to display and/or alter overall system
parameters rather than those that affect a specific source or channel.
Use the Advancedmenu whenever you need to work with or replace the lamp, select a test pat-
tern, define a new color temperature, or access lesser-used image control settings intended for
experienced users.
Projector Configuration
Choose from Floor Front, Floor Rear, Ceiling Front, Ceiling...