Runco Vx 6c Projector User Manual

INSTALLATION AND SETUP
2.11 Keypad Protocols and Conversion
The keypad is assigned “A” as its default protocol, which is simply a collection of settings that
determine how the keypad operates. Once assigned, this protocol remains in effect until it is
changed-that is, the keypad will operate as it currently does until you change its protocol.
Protocols are most useful for multiple-projector applications. For example, you might want to
change a keypad protocol if you are working with two projectors and...

INSTALLATION AND SETUP
2-15 Remote KeypadProtocol  - IR OR WIRED KEYPAD -
The standard IR remote keypad or the optional wired remote can be set to one of two 
different protocols -  “A” or “B”. To hard-wire a protocol to “A” or “B” in either remote, 
follow Steps 1 through 5: 
Step 1
Unplug the keypad from the projector (applies to wired remote only). 
Step 2
Unlatch and open the empty battery compartment on the back of the keypad as shown below.
NOTE: A wired keypad opens as shown, but a cable passes...

INSTALLATION AND SETUP
zJ1jumper: For either remote, set between pins 1 and 2 to set as Protocol “A”. Set between
pins 2 and 3 to set as Protocol “B”.
zJ2jumper: For either remote, set between pins 2 and 3 as shown; otherwise, the projector
will not respond correctly to keypad commands.
zJ3jumper: For the IR remote, make sure that the jumper is set between pins 2 and 3 as
shown. For the wired remote, make sure that the jumper is set between pins 1 and 2 as
shown.
zJ4jumper: For the IR remote, make sure...

INSTALLATION AND SETUP
SHORTCUT METHOD:
You can also issue software protocol settings through the keypad. These software commands
will be lost when the keypad is either unplugged or when a battery is removed - the keypad will
revert back to the hard-wired jumper settings (see above) until you enter the software com-
mands again.
Press                                     = Protocol “A”
Press                                     = Protocol “B”
NOTE: If you change any keypad to a new protocol and the...

From Runco Digital Home Cinema, select Installation use 
passcode 3151 for access.
Then select Operational Parameters from the menu items.  
Once in the Operational Parameters menu select ISF C3 
Calibration. The menu will appear as shown to the right:
• Use            to select characters 
• Use to move cursor
• Use to accept input data
2-18 ISF 3C Calibration
The Splash Screen:
This screen appears for 10 sec. upon startup everything 
it shows customer name and calibrator’s name.  It is the 
seal of a...

Calibration Counter 5
Resolution Digital Cinema
Operational Parameters
Name
Serial No.
Xenon Lamp Adjust
Projector Hours
Information
Customer Name        
Calibrator Name      
Date of Calibration    
Next Calibration      J. Chan
Andy S.
11/17/03
11/17/04
Runco VX-4c / VX-6c
123456789
20
152
Memory Bank Label
Memory Bank No. 02
Sync
Sample Rate       120Mhz
2-19
How to read and reset the calibration counter. From Runco Digital Home Cinema select 
Information to read time elapsed since last calibration...

3.1 Overview
This section explains how to use the projector once it has been installed. Please read through these
pages before using the projector for the first time. An understanding of projector features and how
to access them will help you to take full advantage of the capabilities of the projector within min-
utes.
NOTE: Installation involves locating the projector and adjusting it for use at that location. If you
have not yet installed the projector, refer to Section 2, Installation and Setup.
3.2...

OPERATION
AC LINE CORD INPUT- The projector requires AC power of 100 to 240 VAC, 50 to 60 Hz
(11.5 amps @ 100 VAC, 5.5 amps @ 220 VAC). Always use the line cord that is supplied with
the projector-the projector requires this high-current 13A rated cord. See complete power speci-
fications in Section 5.
WARNING
Do not attempt operation if the AC supply is not
within the specified voltage and power range.
STATUS/POWER LEDS- Two LEDs (light emitting diodes) located in the lower right corner of
the rear...

OPERATION
3.3 Using the KeypadThe keypad appears in two locations:
z Infrared (IR) Remotefor wireless control up to 100 feet away
z Wired Remote(optional) tethered to the rear of the projector
While each keypad is identical in layout and provides complete control of the projector, you may
find one keypad more convenient than another for your specific installation and application. 
IR Remote 
The IR Remote Keypad controls the projector by way of wireless communications from a battery-
powered infrared...

OPERATION
Input 2
Press         to select the source connected to INPUT 2on the projector (an optional interface).
This is the same as entering                .
Input 3
Press         to select the source connected to INPUT 3on the projector (composite video). This is
the same as entering                .
Input 4
Press         to select the source connected to INPUT 4on the projector (S-Video). This is the same
as entering 
Input
Press                  when you want to display from a specific source...