Runco Vx 6000d Projector User Manual

Operation
Runco VX-6000d Owner’s Operating Manual 69 
PREL
IMINARY
Table 4-3 describes the effects of adjusting the primary color hues. 
 Saturation: This slidebar adjusts the color saturation level – the amount of that color in 
a video image. Lower settings produce less saturated colors; a setting of “-30” 
removes that color from the image entirely. If the saturation is too high, that color will be 
overpowering and unrealistic.
Intensity: This slidebar adjusts the intensity – also known as...

Operation
70 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Automatic Contrast: The VX-6000d can dynamically adjust the contrast (white level) 
according to the color content in the signal, to produce the best picture quality. Select 
Automatic Contrast from the Picture Adjust menu to activate this feature. Set it to Off, 1, 2, 
or 3 as desired. Selecting “3” results in a higher average white level than the other 
settings. 
Default: To reset all picture quality settings for the current input to...

Operation
Runco VX-6000d Owner’s Operating Manual 71 
PREL
IMINARY
OptionsSelect Options from the Main Menu to perform the following projector configuration tasks.
Overscan (480i/480p signals only): Refer to Overscan on page 58.
Default: To reset the Overscan setting to its default value, select Default from the Options 
menu, then select Yes to confirm the reset. 
LED: Select LED from the Options menu to change the behavior of the projector’s 
indicator LEDs. 
 When set to ON, the LEDs indicate...

Operation
72 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Power Save: Select Power Save from the Options menu to access the power 
management features of the VX-6000d.
 RS-232C Port: When this option is set to On, the RS-232 port is always active and 
consuming power, even when the projector is in standby mode. When set to Off, the 
RS-232 port is inactive and does not consume power when the projector is in standby 
mode. 
 
Auto Power Off: When this option is set to On, the projector enters...

Runco VX-6000d Owner’s Operating Manual 73 
PREL
IMINARY
5.1 
Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or 
sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to 
obtain a replacement lamp.
1. Turn off the projector and unplug the power cord. Allow the projector to cool down for 
approximately 45 minutes prior to removing the lamp assembly for replacement.
2. Using a flat-blade screwdriver, loosen the two...

Maintenance and Troubleshooting
74 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
5.2 
Lens Replacement
Figure 5-1 shows the VX-6000d lens assembly. 
Figure 5-1. VX-6000d Lens Assembly Exploded View
1. Remove the Projector Front Jewelry by 
loosening the captive #2 Phillips screw 
below the lens.
 
 
 
 
 
 
 
 
Only trained, authorized Runco dealers should attempt to 
remove or replace a lens. Please read this procedure 
carefully before doing so. 
Lens replacement is normally performed at the...

Maintenance and Troubleshooting
Runco VX-6000d Owner’s Operating Manual 75 
PREL
IMINARY
2. Locate and unplug the Motor Assembly 
Connector. Note the connector 
orientation for when you install the new 
lens. 
 
 
 
 
 
 
3. Locate the six 9/64” Hex Mounting 
Screws (two each at 12
 oclock, 
9
 oclock and 6 oclock). 
4. Remove the six Mounting Screws while 
supporting the Lens Assembly; Lens 
and Motor Assembly are now free.
 
 
 
5. Remove the Lens and Motor Assembly 
by pulling forward and to the left...

Maintenance and Troubleshooting
76 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
5.3 
Troubleshooting Tips
Table 5-1 provides some general guidelines for troubleshooting problems you may 
encounter with the VX-6000d. 
If you encounter an issue not described here or in Section 3 (refer to Installation 
Considerations on page 22), or if the suggested solutions fail to resolve the problem, 
please contact your Runco dealer or Runco Technical Support. 
Table 5-1. Troubleshooting Chart 
SymptomPossible...

Maintenance and Troubleshooting
Runco VX-6000d Owner’s Operating Manual 77 
PREL
IMINARY
Image geometry is incorrect. Incorrect aspect ratio 
selection.  Select the aspect ratio that 
best matches the source 
image and screen size 
(refer to 
Table 4-1). 
The projected image is 
trapezoidal in shape.  The projector is not 
perpendicular to the 
screen.  Adjust the projection angle 
or apply keystone 
correction (refer to 
Display Device on 
page 62). 
The projector will not turn 
back on after it was...

Maintenance and Troubleshooting
78 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Notes: