Runco Vx 6000d Projector User Manual

Operation
Runco VX-6000d Owner’s Operating Manual 59 
PREL
IMINARY
CalibrationUse the Calibration menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only. 
To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the ISF 
Presets menu (see above). 
ISF Night - Display Color: Use the Display Color settings to change the characteristics 
of the output signal. These settings are global (independent of any particular input)....

Operation
60 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
ISF Night - Input Color: The Input Color controls are similar to those in the Display Color 
menu (see above), but can be set independently for each input. 
 Gain/Offset: Refer to ISF Night - Display Color, above. 
 Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a 
Composite, S-Video or Component video source. Chroma delay in an image causes 
color shifts to occur to the left of the vertical edge...

Operation
Runco VX-6000d Owner’s Operating Manual 61 
PREL
IMINARY
Runco/ISF Logo Splash Screen Timers: When you turn on the VX-6000d, it 
projects a welcome screen with the Runco logo followed by one with the ISF logo. 
Select Splash Timer from the 
Splash Configure menu to set the amount of time that 
these two images appear. The range is from 2 to 60 seconds, in one-second 
increments. 
Use the up or down cursor button to select a timer value to adjust. Use the right or left 
cursor button to change...

Operation
62 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Remote Control: The Remote Control menu shows you the primary and secondary 
infrared (IR) codes to which the VX-6000d will respond. By default, both are set to 17. You 
can change these codes if either:
 Another device in the theater (a DVD player, for example) is responding to commands 
from the standard DHD remote control (
Figure 2-5) in ways that are unpredictable or 
undesirable.
 You have multiple VX-6000d projectors and want to...

Operation
Runco VX-6000d Owner’s Operating Manual 63 
PREL
IMINARY
HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are 
known, select HD Format from the Service menu and set them as described below. Doing 
so can reduce the time it takes the DHD Controller to switch from HD to 480i signals or 
vice versa. 
This is generally not necessary unless the DHD Controller – for whatever reason – has 
difficulty determining the color space (RGB or YUV), bandwidth or resolution of...

Operation
64 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Resolution: When using the VX-6000d with a computer or certain HD sources, you may 
want to force the DHD Controller to use a specific output resolution. If so, select 
Resolution from the Service menu and choose one. Then, press ENTER to confirm. 
System Reset: To reset ALL projector and controller settings (including image settings) 
back to their factory defaults, choose System Reset from the Service menu. 
A confirmation message...

Operation
Runco VX-6000d Owner’s Operating Manual 65 
PREL
IMINARY
Figure 4-6. OSD Menu Structure for VX-6000d (1080i Digital or 1080p Sources) 
Picture Adjust
Picture MemoryStandard, Black Enhance,  
White Enhance, ISF Day, 
ISF Night or Custom
Contrast
-90, -89, ... 0 ... +89, +90
Brightness
Color
-30, -29, -28 ... 0 ... +28, 
+29, +30 Tint
Sharpness
Color Temp.5500, 6500, 7500, 8500, 
9300 or 10500
White BalanceStandard, Black Enhance,  
White Enhance, ISF Day, 
ISF Night or Custom
RVR: IrisHigh...

Operation
66 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Main MenuPress MENU on either the remote control or built-in keypad (on the projector rear panel) 
to display the Main Menu, shown in 
Figure 4-7. The Main Menu is the starting point for 
calibrating the VX-6000d to optimize the display of digital 1080i and 1080p sources. 
Figure 4-7. VX-6000d Main Menu (1080i Digital or 1080p Sources Only)
To use the on-screen menus:
1. Press  or  to select a sub-menu.
2. Press  or  to select a sub-menu...

Operation
Runco VX-6000d Owner’s Operating Manual 67 
PREL
IMINARY
LanguageThe VX-6000d OSD language is initially set to English, but can also display the menus in 
German (Deutsch), Spanish (Español), French (Français) or Italian (Italiano). To change the 
OSD language:
1. Press MENU.
2. Press  or  to select Language from the Main Menu.
3. Press up- or down-arrow button ( or ) to highlight the desired language and press 
ENTER. The change takes effect immediately. 
Picture AdjustTo perform basic picture...

Operation
68 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Contrast: Refer to Contrast on page 55. 
Brightness: Refer to Brightness on page 54. 
Color: Refer to Color Saturation on page 55. 
Tint: Refer to Tint on page 56. 
Sharpness: Refer to Sharpness on page 57. 
Color Temp.: To adjust the color temperature, select Color Temp. from the Picture 
Adjust menu. (Color temperature defines the “color of gray.”) Press  or  to select 
5500, 6500, 7500, 8500, 9300 or 10500. In most cases, 6500 or 7500...