Runco Vx 6000d Projector User Manual

Installation
Runco VX-6000d Owner’s Operating Manual 39 
PREL
IMINARY
Connecting to AC PowerProjector/DHD Controller: The VX-6000d system includes two (2) AC power cords 
(one each for the projector and DHD Controller).
Plug the female end of one power cord into the AC receptacle on the rear of the 
VX-6000d (AC 100V ~ 240V). Then, connect the other end to your AC power source. 
Similarly connect the DHD Controller to a nearby AC outlet. 
AutoScope Lens Motor: With AutoScope-equipped projectors, a third...

Installation
40 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
3.8 
Adjusting the Picture 
Orientation
By default, the VX-6000d is configured for a “floor/front” installation, in which the projector 
is installed upright and in front of the screen. If it is installed behind the screen and/or 
mounted on a ceiling, you must change the picture orientation. To do this:
1. Select an input OTHER THAN HDMI 1 or HDMI 2 on the DHD Controller. 
2. Press MENU (on menu page 4) and enter the Service Menu...

Installation
Runco VX-6000d Owner’s Operating Manual 41 
PREL
IMINARY
Vertical and Horizontal 
Lens Shift
To change the projected image position, use a 3/16” hex driver to shift the lens in the 
desired direction; see 
Figure 3-17. The vertical lens shift control is at the top of the 
projector; the horizontal lens shift control is on the side of the projector nearest the Runco 
logo. (The tool will automatically center on top of the adjustment nut when inserted into 
the access hole.) 
Figure 3-17....

Installation
42 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
3.10 
Installing and 
Adjusting the 
CineWide Anamorphic 
Lens
If you are installing a CineWide-equipped projector, proceed as follows to install and 
adjust the anamorphic lens. 
Attach Lens Mounting 
Assembly to Lens Motor 
Carriage Plate (CineWide 
with AutoScope) or Base 
Plate (fixed CineWide)
The VX-6000d Anamorphic lens mount kit consists of everything shown in Figure 3-18. 
Some components shipped with your projector may differ...

Installation
Runco VX-6000d Owner’s Operating Manual 43 
PREL
IMINARY
4. Use the Lens Rotation Set Screws to attach the Lens Adapter Ring (item #1) to the 
Pitch Adjustment Yoke (item #2); see 
Figure 3-19. (Use the curved, oval-shaped holes 
on the Pitch Adjustment Yoke.)
5. Use the Height/Y Adjustment T-Screws (item #3), Pitch Adjustment T-Screws 
(item
 #4) and Washers to attach the Pitch Adjustment Yoke and Lens Adapter Ring to 
the Anamorphic Lens Holder. The Yoke should be as close to the primary...

Installation
44 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Configure Lens Motor 
Trigger 
(CineWide with 
AutoScope)
(Skip this step if you are installing a fixed CineWide anamorphic lens.) 
CineWide with AutoScope maintains constant image height independent of the aspect 
ratio, while using the full display resolution of the projector. It accomplishes this by moving 
the anamorphic lens in front of the primary lens when widescreen material is being viewed. 
When the viewer transitions back to...

Installation
Runco VX-6000d Owner’s Operating Manual 45 
PREL
IMINARY
When the height is properly set, tighten the Height Adjustment T-Screws to secure the 
lens in place.
Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. 
To do this, loosen the Pitch Adjustment T-Screws (directly below the Height/Y
 Adjustment 
T-Screws) on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic 
lens angle so that the projected image is rectangular: 
The...

Installation
46 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely 
from side to side. Then, angle the lens to even out any left-right pincushion distortion: 
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Adjusting the Geometry: 
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Loosen the three Lens Rotation Set Screws (shown in...

Installation
Runco VX-6000d Owner’s Operating Manual 47 
PREL
IMINARY
Focus: Finally, rotate the Focus Ring on the anamorphic 
lens to fine-tune the optical focus. 
FOCUS 

Installation
48 Runco VX-6000d Owner’s Operating Manual
PREL
IMINARY
Notes: