Runco V 63hd Installation And Operation Manual

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 37 
PREL
IMINARY
Height: Select Height from the Input Position menu to change the projected image 
height. Press  to increase the height; press   to decrease it.
Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture 
area of the video signal out beyond the edge of the display area. 
Some television programs are produced based on the assumption that older television 
sets may not display the outer edges of...

Operation
38 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Phase (RGB, Component or SCART sources): This control adjusts the phase of the 
pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB, 
Component or SCART image still shows shimmer or “noise” after Tracking has been 
optimized. 
For best results, use a good test pattern such as a smooth gray consisting of a clear 
pattern of black and white pixels, or a similar “half on, half off”...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 39 
PREL
IMINARY
You should save changes to any of the following settings to a preset; otherwise they will 
be lost when a new input source or resolution is selected:
 Brightness

 Color saturation

 Sharpness

 Color temperature and white balance
To select a memory preset, press   or   to highlight it and press ENTER. 
To save the settings for the current input and display mode to the Custom 1 or Custom 2 
memory preset, select...

Operation
40 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
InformationSignal / System: Select Information from the Main Menu, then choose either Signal or 
System to display information about the current input signal (resolution, frequency, type et 
cetera) and installed firmware versions, as well as other information that uniquely identifies 
your DHD Controller and display device. 
Should you ever need to contact Runco Technical Support, this information will help them...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 41 
PREL
IMINARY
Calibration Use the Calibration menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only. 
To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the 
Memory Presets menu (see page 38) or use the corresponding remote control buttons. 
Display Color - Common Settings: Use the Display Color - Common Settings menu to 
adjust the color...

Operation
42 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
 Color Temp: Select Color Temp from the Display Color - Common Settings menu to 
adjust the color temperature. Color temperature establishes the “color of gray” by 
adjusting the 75% white point to various color points. 
What are “color points?”A “color point” is an x/y coordinate pair that defines a 
color’s location on the standard CIE chromaticity graph, shown in Figure 4-7. (CIE 
stands for “Commission...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 43 
PREL
IMINARY
Display Color - Panel Settings: These settings are also saved independently for each 
input and display mode.
 Panel Brightness: The Panel Brightness control changes the apparent brightness of 
the displayed image. Its effect is similar to that of a lamp intensity control on a projector. 
Use a higher setting for rooms with a lot of ambient light. Use a lower setting for more 
“theater-like” viewing conditions...

Operation
44 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you 
should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to 
do this.
  Copy/Paste - Memory Preset: You can copy and paste settings from one memory 
preset to another. This gives you a convenient starting point for creating a new preset 
based on an existing one, to make the calibration process less...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 45 
PREL
IMINARY
spect Ratio - Paste Settings: To apply the Output Shift and Image Alignment 
settings on the clipboard to a different aspect ratio and/or screen, do either of the 
following:
 Switch to another aspect ratio (for example, from 16:9 to Cinema).
 Switch from Screen 1 to Screen 2 or vice versa.
Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings 
are saved automatically.
Output Shift:...

Operation
46 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
To correct keystoning or pincushion distortion:
1. On the DHD Controller remote control or front panel, press MENU.
2. Select Calibration from the Main Menu and enter the Calibration Menu passcode. 
3. Select Image Alignment from the Calibration Menu.
4. Select Corner Alignment to correct a “keystoned” image by adjusting the image 
corner positions. Select Midpoint Alignment to correct pincushion distortion by...