Runco V 63hd Installation And Operation Manual

Controls and Functions
Vistage™ Series Flat-Panel Display Installation/Operation Manual 7 
PREL
IMINARY
The rear-panel connectors reside behind protective cover plates with cable routing slots. 
Use a Phillips screwdriver to remove the plates in order to connect cables, and to 
re-attach them afterward. 
 
1.AC POWER INPUT
Connect the V-50HD/V-63HD to AC power here. 
2.DHD INPUT PANEL
SECONDARY INPUT
For future use.
SERVICE PORT
For future use.
PRIMARY INPUT
HDCP-compliant digital video input. Connect...

Controls and Functions
8 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
2.3 
DHD Controller Rear 
PanelFigure 2-5 shows the rear connector panel on the DHD Controller.
Figure 2-5. DHD Controller Rear Panel
1.POWER INPUT (100 to 240 VAC)
Connect the DHD Controller to power here. 
2.HD1 / HD2 (5 x Analog BNCs)
Two inputs (five BNCs per input) for connecting standard-definition (SD = 480i/576i), 
enhanced-definition (ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p)...

Controls and Functions
Vistage™ Series Flat-Panel Display Installation/Operation Manual 9 
PREL
IMINARY
2.4 
V-50HD/V-63HD 
Remote Control Unit Figure 2-6 shows the V-50HD/V-63HD remote control, and the paragraphs that follow 
describe its functionality.
Figure 2-6. DHD Controller/V-50HD/V-63HD Remote Control
ON
ISF
NT
VID
1VID
2
HD
1HD
2VID
3
COMP
ISF
DAYCUST
1CUST
2
OFF
RATIO
RATIO I
N
P
U
TI
N
P
U
T
EXIT
123
456
HDMI
1
HDMI
3HDMI
4 HDMI
2SCART
NATIVE
78
09
MENU LIGHT
ENTER
16 : 9 4 : 3LET
BOX
V-WIDE...

Controls and Functions
10 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
1.IR OUTPUT INDICATOR
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2.LIGHT 
Press to illuminate the buttons.
3.ON / OFF
Press to turn the DHD Controller and display on or off.
4.ENTER
Press to select a highlighted menu item or confirm a changed setting.
5.Cursor Buttons (, , , ) 
Use these buttons to select items or settings, adjust settings or switch display...

Controls and Functions
Vistage™ Series Flat-Panel Display Installation/Operation Manual 11 
PREL
IMINARY
10.HD 1 (4) / HD 2 (5) 
Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric 
character “4” or “5.” 
11.COMP (Component) (6) 
Press to select the Component video input as the source or to enter the numeric 
character “6.”
12.HDMI 1 (7) / HDMI 2 (8) / HDMI 3 / HDMI 4 (0)
Press to select an HDMI input as the source or to enter the numeric character “7,” “8” 
or “0.” 
13.SCART...

Controls and Functions
12 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Notes:
 

Installation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 13 
PREL
IMINARY
3.1 
Remote ControlTo install batteries in the remote control: 
1. Press down the tab on the cover and 
pull the cover in the direction of the 
arrow.
2. Insert the included batteries. Ensure 
that the polarities correctly match the 
 and   markings inside the battery 
compartment.
3. Insert the lower tab of the cover into 
the opening, and press down the cover 
until it clicks in place.
Notes on Batteries...

Installation
14 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Notes on Remote Control
Operation Make sure that there is nothing obstructing the infrared beam between the remote 
control and the IR receiver on the DHD Controller.
 If the effective range of the remote control decreases, or it stops working, replace the 
batteries with new ones.
 The remote control may fail to operate if the infrared remote sensor is exposed to bright 
sunlight or fluorescent lighting....

Installation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 15 
PREL
IMINARY
3.3 
Installation 
ConsiderationsProper installation of your V-50HD/V-63HD will ensure the highest possible picture quality. 
Whether you are installing the V-50HD/V-63HD temporarily or permanently, you should 
take the following into account to ensure that it performs optimally.
Mounting the 
V-50HD/V-63HD on a Wall 
or Table Stand To install the V-50HD/V-63HD, you will need either an optional table stand or...

Installation
16 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
VentilationIf you are mounting the V-50HD/V-63HD in an enclosure, leave sufficient space on all 
sides between it and surrounding objects, as shown in Figure 3-1. This allows heat to 
disperse, maintaining the proper operating temperature. 
Figure 3-1. Ventilation Requirements for Enclosure Mounting
Ambient LightIn general, minimize or eliminate light sources directed at the display. Contrast ratio in your...