Runco V 63hd Installation And Operation Manual

Installation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 17 
PREL
IMINARY
3.4 
Connections to the 
V-50HD/V-63HD and 
DHD ControllerProceed as follows to connect the DHD Controller to the V-50HD/V-63HD, your video 
sources, external controller(s) – if present – and AC power.
To access the rear-panel connectors, use a Phillips screwdriver to loosen the screws 
securing the protective cover plates (see Figure 2-3) to the panel, then remove the plates.
When connecting your equipment:...

Installation
18 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Connecting Source
Components to the DHD
ControllerConnect your video sources to the DHD Controller as shown and described in the 
sections that follow. 
HDMI Source Connections: See Figure 3-3. 
Figure 3-3. HDMI Source Connections➤
Use the HDMI inputs whenever possible. Not only does this ensure 
the best possible picture quality, it provides a communication 
channel for CEC command messages between the display...

Installation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 19 
PREL
IMINARY
Component Video Source Connections: Connect your component video sources to 
the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-4. 
Figure 3-4. Component Video Source Connections
Video 1 Y Video 2
Video 3
Pr Pb Pr
R Pb
B Y
GHD1
HD2
HV
Y PBPR COMPONEN T
VIDEO OUT 
BD/DVD
DTV-Set-Top Box
(DTV-STB) 
RCA-to-BNC
adapter
 

Installation
20 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
RGBHV Source Connections: Connect personal computers and/or other RGB sources 
to the HD1 and/or HD2 inputs as shown in Figure 3-5. 
Figure 3-5. RGBHV Source Connections
Pr
R Pb
B Y
G
HD1
HD2
HV
or
ComputerRGB Camcorder
Green
Blue
Red
H-Sync
V-Sync
 

Installation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 21 
PREL
IMINARY
SCART RGBS Source Connections: Connect the green, blue and red outputs from 
your SCART source to the Component/SCART input on the DHD Controller. Connect the 
sync output from your SCART source to the Video 1 input on the DHD Controller. See 
Figure 3-6. 
Figure 3-6. SCART RGBS Source Connection
Composite Source Connections: See Figure 3-7. 
Figure 3-7. Composite Video Source Connections
Video 1 Y Video 2...

Installation
22 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Connecting an Audio
Processor or Secondary
Display Device to the DHD
Controller (Optional)The DHD Controller provides a second HDMI output (labeled HDMI Out (Audio Only)) for 
connection to an audio receiver/switching system or secondary display device for 
monitoring purposes. See Figure 3-8. 
Figure 3-8. Audio Processor Connection to DHD Controller➤
The DHD Controller does not transmit HDMI CEC control...

Installation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 23 
PREL
IMINARY
RS-232 Controller 
Connection Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation 
system (if present) to the RS-232 port on the DHD Controller; see Figure 3-9. 
For more information about using this connection, refer to External Control on page 59.
Figure 3-9. RS-232 Control System Connection
Ethernet Network 
Connection Use a standard, Category 5 network cable with an RJ-45 plug...

Installation
24 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Connecting to AC PowerThe V-50HD/V-63HD ships with two (2), AC power cords: one for the DHD Controller and 
one for the display.
1. Plug the female end of one of the power cords into the AC receptacle on the rear of 
the V-50HD/V-63HD (AC 100V ~ 240V); see Figure 2-3. 
2. Connect the other end to your AC power source. 
3. Re-attach the AC input cover plate, routing the power cord through the slot on the 
plate....

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 25 
PREL
IMINARY
4.1 
Setting the Computer 
Display PropertiesTo maximize image quality when using the V-50HD/V-63HD with a personal computer, 
you may need to adjust the display properties of your computer’s video card. To do this 
on a Microsoft® Windows®-based PC: 
1. Choose Settings from the Windows Start 
Menu and click on “Control Panel.”  
2. Double click on the Display icon.
3. Click the Settings tab on the display dialog...

Operation
26 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
5. Click the Advanced button and click the 
Monitor tab on the dialog box. Set the 
Refresh Frequency to 60Hz and click 
OK.
1. The native resolution of the V-50HD/V-63HD is 1920 x 1080. 
Other horizontal or vertical resolutions may be scaled upward or 
downward to fit the display.
2. With most computers, you can get the best picture at 
1024 x 768 @ 60Hz.
To prevent image retention (burn) on your display, ALWAYS...