Home > Runco > Projector > Runco Sc 1 Projector User Manual

Runco Sc 1 Projector User Manual

Here you can view all the pages of manual Runco Sc 1 Projector User Manual. The Runco manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 61

Installation
Runco SC-1 Owner’s Operating Manual 49 
PREL
IMINARY
3.12 
Installing and 
Adjusting the 
CineWide Anamorphic 
Lens
If you are installing a CineWide-equipped projector, proceed as follows to install and 
adjust the anamorphic lens. 
The SC-1 Anamorphic lens mount kit consists of everything shown in Figure 3-27. Some 
components shipped with your projector may differ slightly from what is shown in these 
instructions. If any items are missing or damaged, please contact your Runco dealer or...

Page 62

Installation
50 Runco SC-1 Owner’s Operating Manual
PREL
IMINARY
3. Secure the Anamorphic Lens Holder to the plate using the Hex Bolts/Washers (item #6) 
and Yaw/X
 Adjustment Levers that you removed in Step 1. 
4. Use the Lens Mounting Screws to attach the Lens Adapter Ring (item #1) to the Pitch 
Adjustment Yoke (item #2); see 
Figure 3-28. (Use the round, threaded holes on the 
yoke.)
5. Use the Height/Y Adjustment T-Screws (item #3), Pitch Adjustment T-Screws (item #4) 
and T-Nuts (item #9) to attach...

Page 63

Installation
Runco SC-1 Owner’s Operating Manual 51 
PREL
IMINARY
Configure Lens Motor 
Trigger 
CineWide with AutoScope maintains constant image height independent of the aspect 
ratio, while using the full display resolution of the projector. It accomplishes this by moving 
the anamorphic lens in front of the primary lens when widescreen material is being viewed. 
When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens 
moves out of the light path.
To configure the lens...

Page 64

Installation
52 Runco SC-1 Owner’s Operating Manual
PREL
IMINARY
Adjusting the Height (Y): With the white field still on-screen, loosen the 
Height/Y
 Adjustment T-Screws on either side of the lens. Then, slowly move the 
anamorphic lens into place so that there are no shadows on the top or bottom of the 
screen: 
When the height is properly set, tighten the Height Adjustment T-Screws to secure the 
lens in place.
Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion....

Page 65

Installation
Runco SC-1 Owner’s Operating Manual 53 
PREL
IMINARY
Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers 
to allow the lens to pivot freely from side to side. Then, 
angle the lens to even out any left-right pincushion 
distortion: 
 
 
 
 
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Adjusting the Geometry: 
1. Input an anamorphic cross-hatch test pattern to the DHD Controller.
2. Unscrew the Anamorphic Lens just enough...

Page 66

Installation
54 Runco SC-1 Owner’s Operating Manual
PREL
IMINARY
3.13 
Calibrating Projector 
Input 2 (DVI)
After you have installed and adjusted the projector and lens (or lenses), you are ready to 
begin calibrating the DVI input (Input 2) to the SC-1.
To perform the calibration, you will use the SC-1 built-in keypad (Figure 2-3) or 
TheaterMaster Remote Control, shown in Figure 3-29 and described on the pages that 
follow. Once you have completed the projector input calibration, the end user can use...

Page 67

Installation
Runco SC-1 Owner’s Operating Manual 55 
PREL
IMINARY
Figure 3-29. TheaterMaster Remote Control for SC-1
SYSTEM
MENU
MENUGUIDEGUIDE
EXIT
INFO
DIS
PREVPREVCHCH+
-
+
-
MAIN
                  FUNCS
SOURC
1
32
4
11
13 12
14109 8 76 5 

Page 68

Installation
56 Runco SC-1 Owner’s Operating Manual
PREL
IMINARY
TheaterMaster Remote 
Control Functions
1.POWER Button  
Hold this button down for 1-2 seconds to turn on or off the projector.
2.FUNCS Button  
This button brings you to a sub-page in which you can access the projector’s internal 
test patterns, view help text, auto-calibrate the projector and perform various other 
functions.
3.BACKLIGHT Button  
Lights the LCD display and buttons for use in a dark room.
4.LCD Display  
Displays...

Page 69

Installation
Runco SC-1 Owner’s Operating Manual 57 
PREL
IMINARY
Navigating the Projector 
Menus
Most of the controls for the projector are accessed from within the projector’s menu 
system. There are several groups of related functions, with each group selectable from the 
Main Menu. Press MENU on the built-in keypad or TheaterMaster remote to display this 
menu. 
To select a sub-menu using the remote keypad, do one of the following: 
 Press the number key corresponding to the function menu you wish to...

Page 70

Installation
58 Runco SC-1 Owner’s Operating Manual
PREL
IMINARY
All available channels are listed in the Channel Setup menu (Figure 3-30), which describes 
how each channel can be accessed and which serves as the gateway for editing, copying 
and deleting channels. 
Figure 3-30. Channel Setup Menu
To display the Channel Setup menu, press 3 or highlight Channel Setup and press 
ENTER or 
. The Channel Setup menu appears with the active channel highlighted. 
What Appears in the Channel Setup Menu: This...
Start reading Runco Sc 1 Projector User Manual

Related Manuals for Runco Sc 1 Projector User Manual

All Runco manuals