Ricoh Mp C4500 Instruction Manual

Interface Settings
61
2
❖Effective Protocol
Select the protocol to use in the network.
IPv4: Active / Inactive
 IPv6: Active / Inactive
NetWare: Active / Inactive
 SMB: Active / Inactive
 AppleTalk: Active / Inactive
❖NCP Delivery Protocol
Select the protocol for NCP delivery.
IPX Priority
TCP / IP Priority
IPX Only
 TCP / IP Only
If you select IPX Only or TCP / IP Only, you cannot switch the protocol
even if you cannot connect with it. If NetWare in [Effective Protocol] is set to
Inactive, you...

System Settings
62
2
❖Ethernet Speed
Set the access speed for networks.
Select a speed that matches your network environment. [Auto Select] should
usually be selected.
Auto Select
 10Mbps Full Duplex
 10Mbps Half Duplex
 100Mbps Full Duplex
 10Mbps Half Duplex
❖LAN Type
When you have installed the IEEE 802.11b interface unit, select the method of
connection.
Ethernet
 IEEE 802.11b
[LAN Type] is displayed when wireless LAN board is installed. If Ethernet and
IEEE 802.11b (wireless LAN) are both...

Interface Settings
63
2
❖Host Name
Specify the host name.
Enter the host name using up to 63 characters.
❖Machine Name
Specify the machine name.
Enter the machine name using up to 31 characters.
Parallel Interface
This section describes the user tools in the Parallel Interface menu under Inter-
face Settings.
[Parallel Interface] is displayed when this machine is installed with the IEEE 1284
interface board.
❖Parallel Timing
Sets the timing for the control signal of the parallel interface.
ACK Outside...

System Settings
64
2
❖Signal Control
Specifies how error during printing or sending facsimile from the computer
is to be dealt with.
Job Acceptance Priority
Printer Priority
IEEE 1394
This section describes the user tools in the IEEE 1394 menu under Interface Set-
tings.
[IEEE 1394] is displayed when this machine is installed with the IEEE 1394 inter-
face board.
❖IPv4 Address
Before using this machine in the network environment, you must specify the
IPv4 address and subnet mask.
When you select...

Interface Settings
65
2
❖WINS Configuration
Specify the WINS server settings.
If [On] is selected, specify the WINS Server IPv4 address as xxx.xxx.xxx.xxx
(xxx indicates a number).
If DHCP is in use, specify the scope ID.
Enter scope ID using up to 31 characters.
On
 Primary WINS Server: 000.000.000.000
 Secondary WINS Server: 000.000.000.000
Scope ID
Off
❖IPv4 over 1394
When you use the IPv4 over 1394 function of the IEEE 1394 interface to con-
nect the machine to the network, or printing from...

System Settings
66
2
IEEE 802.11b
This section describes the user tools in the IEEE 802.11b menu under Interface
Settings.
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board.
Be sure to make all settings simultaneously.
❖Communication Mode
Specifies the communication mode of the wireless LAN.
802.11 Ad-hoc Mode
 Ad-hoc Mode
 Infrastructure Mode
❖SSID Setting
Specifies SSID to distinguish the access point in infrastructure mode or 802.11
ad hoc mode.
The...

Interface Settings
67
2
❖Wireless LAN Signal
When using in infrastructure mode, you can check the machines radio wave
status using the control panel.
Radio wave status is displayed when you press [Wireless LAN Signal].
❖Transmission Speed
Specifies the communication speed of the IEEE 802.11b (wireless LAN).
Auto Select
 11Mbps Fixed
 5.5Mbps Fixed
2Mbps Fixed
1Mbps Fixed
❖Restore Factory Defaults
You can return the IEEE 802.11b (wireless LAN) settings to their defaults.
No
Yes
Reference
p.3...

System Settings
68
2
BPress [Interface Settings].
CPress [Print List].
DPress the {Start} key.
The configuration page is printed.
EPress [Exit].
FPress the {User Tools/Counter} key.
Note
❒You can also exit by pressing [Exit] on the User Tools main menu. 

File Transfer
69
2 File Transfer
This section describes the user tools in the File Transfer menu under System Set-
tings.
Default settings are shown in bold type.
❖Delivery Option
Enables or disables sending stored or scanned documents to the ScanRouter
delivery server.
On
 Main Delivery Server IPv4 Address 
 Sub Delivery Server IPv4 Address
Off
Specify this option when selecting whether or not to use the ScanRouter de-
livery software. If you do, you will have to preregister I/O devices in the...

System Settings
70
2
 File to Deliver
Specify whether all received fax documents or only received fax docu-
ments that include delivery codes (ID or SUB/SEP codes) are sent to the
ScanRouter delivery software.
 File with Delivery Code
Print File
 Delivery Failure File
If a received fax document cannot be sent to the ScanRouter delivery soft-
ware, it is stored in memory. To print a stored file, select [Print File], to de-
lete, select [Delete File].
If the machine can send the data to the ScanRouter...