RCA 25255re2c Manual

21
Ring Volume
From the Sound Settings Menu:
VOLRing Volume
SELECT
3.    Use the VOL (- or +) button to toggle between L1 and L2 and use the  VOL (- or +) button to 
        scroll to your selection.The default setting is  VOL 3.
SELECT
This feature is used to conveniently access the voicemail feature offere\
d by your telephone service provider.
       NOTE: You must subscribe to telephone service provider-offered voicemail on at least one phone 
       line in order for this feature to operate.
1....

2 2
Outgoing Message (OGA) Playback
From the Answering Sys Menu:
VOLOGA Playback
SELECT
Use VOL(- or+) to select Line1 or Line2, press select softkey and then use Vol(- or +) 
button to select  the direct OGA record.
Use VOL(- or+) to select Line1 or Line2, press select softkey and then use  Vol(- or +) 
button to select  the direct OGA.
Use VOL(- or+) to select Line1 or Line2, press select softkey and then use Vol(- or +) button to 
select the direct OGA record.
an error tone will be emit.
SELECTEMPTY...

2 3  
Set Work Hours
From the Set Ofce Time  Menu:
VOLSet Work Hours
SELECT
AM/PMAMPM
SAVE
5.    Use the Yes or No Soft key for Announce Only.
5.    Use the Yes or No Soft key for Announce Only.NOTE: If you select Yes for Announce Only, 
the “Work Hours” OGA and “After Hours” OGA 
The unit will hang up the call after announcing the greeting when 
answering the call is in the answering mode.
Set After Hours
From the  Set Ofce Time  Menu:
VOLSet After Hours
SELECT
AM/PMAMPM
SAVE
NOTE: If you select Yes for...

2 4
Ring Dela y
From the Answering Sys Menu:
VOLRing Delay
SELECT
SELECT
NOTE: When the Toll saver is selected, the unit will answer the incoming call 
after  3  rings if there is new message. Otherwise, the unit will answer the 
incoming call after  5  rings.
Message Length
From the Answering Sys Menu:
VOLMessage Length
SELECT
SELECT
Call Screening
From the Answering Sys Menu:
VOLCall Screening
SELECTVOLOnOff
SELECT
Message Alert
From the Answering Sys Menu:
VOLMessage Alert
SELECTVOLOnOffOff
SELECT
Use...

25
 
Remote Password
From the Answering Sys Menu:
VOLRemote Password
SELECT000.
SAVE
Restore Setting
From the  Standby or Idle Mode (not in Talk mode) :
menuMENU
VOLRestore Setting
SELECTLOAD TO DEFAULT?
YESthen reset the unit automatically after the base shows  please 
NOTE: Use the Clear soft key or Delete button can delete the exist numbe\
rs and then 
enter the new password.
wait... in the display for about 3 seconds.
NO
Telephone Operation
Making Calls with the Cordless Handset
Talk
line 1line 2...

2 6
Making Calls in the Speakerphone Mode (from the base)
speaker
line 1line 2
One-Touch/Memory Log
speaker
NOTE: After pick the line, the call timer starts to run until all the calls are hung up. The timer serves for both 2 lines.
Making Call in the Speakerphone Mode (from the handset)
Spk
Press the Line1 or Line2 Softkey to select a specific line. The Handset will activate the ear 
piece. Then press the  SPK button to switch to the speakerphone mode.
end
Making Calls with a Wired Headset
headset
Talk...

2 7  
Pre-Dialing
1.   With the phone idle, manually enter the telephone number. The maximum pre-dialing 
number length is  32 digits, if the number is over 32 digits, it will emit an error tone.  The 
telephone number shows in the display.
2.   Press the  DIAL Soft key (on base only),  Spk button,  Talk button (handset only), or  line 
1  or  line 2  button to take a line,  or pick up the corded handset (on the base only)  and 
then the telephone number will be dialed out .
Answering a Call
For cordless...

29  
Redial
 3UHVVWKHTalkEXWWRQRQWKHFRUGOHVVKDQGVHWRUSUHVVWKHSpkEXWWRQVSHDNHUSKRQH
PRGHRUSUHVVWKHheadsetEXWWRQKHDGVHWPRGHRUSLFNXSWKHFRUGHGKDQGVHW
IURPWKHEDVHDQGWKHfiUVWDYDLODEOHOLQHZLOOJRRIIKRRN,IERWKOLQHVDUHDYDLODEOH/LQH
ZLOOEHXVHG
 25
3UHVVDlineEXWWRQWRVHOHFWDOLQH
 3UHVVWKHredialEXWWRQ7KHUHGLDOQXPEHUOLVWODVWSUHYLRXVO\GLDOHGQXPEHUVLV
VKRZQ
 8VHWKHVOLRU...

3 0
Transferring a Call to Another Extension
1.   Press XFER Soft key when the phone is in Talk mode.   The current call is put on hold.
2.   Use  VOL (- or +) to select the desired handset or base you want to transfer to, and then 
press the  SELECT Soft key.
3.   The unit will intercom  ring the selected handset or base. 
  Wait until the selected handset or base answers the intercom call and have a 
conversation and then hang up to  nish the transfer or press Conference to have a 3 
way conference...