Home > LG > Projector > Projector LG Minibeam User Manual

Projector LG Minibeam User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Projector LG Minibeam User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1069 LG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							131EXTERNAL	CONTROL	DEVICE	SETUP
    16. Tune Command (Command: m a)
    * This command may work differently depending on model and signal.
     ►To tune channel to following physical/major/minor number.
    Transmission [m][a][ ][0][ ][Data00][ ][Data01][ ][Data02][ ][Data03][ ]
    [Data04][ ][Data05][Cr]
    Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel from the Major / Minor number, the Physical number is not required when sending a command in Digital.
    * Analog Antenna/Cable
    Data 00: Physical Channel Number -Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) -Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
    [Data 01 ~ 04]: Major/Minor Channel Number
    Data 01 & 02: xx (Don't care)
    Data 03 & 04: xx (Don't care)
    Data 05: Input Source (Analog) -00 : Antenna TV (ATV) -01 : Cable TV (CATV) 
    * Digital Antenna/Cable
    Data 00 : xx (Don't care)
    [Data 01][Data 02] : Major Channel Number
    Data 01 : High byte Channel Data
    Data 02 : Low byte Channel Data -00 01 ~ 27 0F (Decimal: 1 ~ 9999)
    [Data 03][Data 04] : Minor Channel Number
    Data 03 : High byte Channel Data
    Data 04 : Low byte Channel Data  
    						
    							132EXTERNAL	CONTROL	DEVICE	SETUP
    Data 05 : Input Source (Digital) -02 : Antenna TV (DTV) – Use Physical Channel Number -06 : Cable TV (CADTV) – Use Physical Channel Number -22 : Antenna TV (DTV) – Don’t Use Physical Channel Number -26 : Cable TV (CADTV) - Don’t Use Physical Channel Number -46 :  Cable TV (CADTV) – Use Major Channel Number Only  (One Part Channel)
    Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0).
    * Tune Command Examples:1. Tune to the Analog cable (NTSC) channel 35. Set ID = All = 00 
    Data 00 = Channel Data is 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = Analog Cable TV = 01 Total = ma	00	23	00	00	00	00	01
    2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Minor is 3 = 00 03 Data 05 = Digital Antenna TV = 22 Total = ma	00	00	00	1E	00	03	22
    Ack [a][ ][Set ID][ ][OK][Data 00][Data 01][Data 02][Data 03][Data 04]
    [Data 05][x]
    [a][ ][Set ID][ ][NG][Data 00][x]  
    						
    							133EXTERNAL	CONTROL	DEVICE	SETUP
    17. Channel Add/Del (Command: m b)
     ►To skip current channel for next time.
    Transmission [m][b][ ][Set ID][ ][Data][Cr]
    Data
    00 : Del  01 : Add
    Ack [b][ ][Set ID][ ][OK/NG][Data][x]
    * Set the saved channel status to del or add.
    18. Key (Command: m c)
     ►To send IR remote key code.
    Transmission [m][c][ ][Set ID][ ][Data][Cr]
    Data: To see "KEY CODES".
    Ack [c][ ][Set ID][ ][OK/NG][Data][x]
    19. Energy Saving (Command: n p)
     ►Sets the energy saving mode.
    Transmission [n][p][ ][Set ID][ ][Data][Cr]
    Data
    00 : Minimum 01 : Medium
    02 : Maximum
    Ack [p][ ][Set ID][ ][OK/NG][Data][x]  
    						
    							134EXTERNAL	CONTROL	DEVICE	SETUP
    20. Input select (Command: x b) (Main Picture Input)
     ►To select input source for main picture.
    Transmission [x][b][ ][Set ID][ ][Data][Cr]
    Data
    00 : DTV  01 : CADTV
    11 : CATV 10 : ATV
    20 : AV 40 : Component
    60 : RGB 90 : HDMI
    Ack [b][ ][Set ID][ ][OK/NG][Data][x]
    * This function depends on model and signal.
    21. 3D (Command: x t)
     ►To change 3D mode for Projector.
    Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02]
    Data Structure
    [Data 00] 00 : 3D On
     01 : 3D Off
     02 : 3D to 2D
    [Data 01] 00 : Top and Bottom
     01 : Side by Side
     03 : Frame Sequential
    [Data 02] 00 : Right to Left
     01 : Left to Right[Data 02] functions depend on model and signal.  
    						
    							135EXTERNAL	CONTROL	DEVICE	SETUP
    * All 3D pattern options ([Data 01]) may not be available according to broadcasting/video signal.
    [Data 00][Data 01][Data 02]
    00OO
    01XX
    02XX
    X : don’t care
    Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02][x]
    [t][ ][Set ID][ ][NG][Data00][x]
    22. Extended 3D (Command: x v)
     ►To change 3D option for Projector.
    Transmission [x][v][ ][Set ID][ ][Data 00][ ][Cr]
    Data 00 : Right to Left  01 : Left to Right
    Ack [v][ ][Set ID][ ][OK/NG][Data 00][x]
    23. Auto Configure (Command: j u)
     ►To adjust picture position and minimize image shaking automatically.It works only in RGB (PC) mode.
    Transmission [j][u][ ][Set ID][ ][Data][Cr]
    Data 01 : Run Auto Configure
    Ack [u][ ][Set ID][ ][OK/NG][Data][x]  
    						
    							136EXTERNAL	CONTROL	DEVICE	SETUP
    Open	Source	Software	Notice	Information
    To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://\
    opensource.lge.com.In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to [email protected]. This offer is valid for three (3) years from the date on which you purchased the product.  
    						
    All LG manuals Comments (0)

    Related Manuals for Projector LG Minibeam User Manual