Projector Christie Vivid Red User Manual

Cleaning the Case
Cleaning the Lens
Cleaning the Lamp Wipe lightly with a soft, dry cloth. If the case is very dirty, clean the case with
a soft, dampened cloth using mild commercial cleaner and finish with a dry
cloth. Do not use liquid or aerosol cleaners.
To prevent scratching the lens, clean the lens only if absolutely required.
Clean the lens with a commercially available blower or cleaning paper gently
in a circular motion.
It is important to never touch the glass surface of the lamp, as the oil...

To Replace the Lamp:
To Reset the Lamp Timer: 1. Loosen the lamp cover screw and remove the lamp cover.
2. Loosen the two screws securing the lamp housing. Remove the lamp
housing by pulling on the handle.
3. Insert a new lamp housing until it is plugged into the socket.
4. Secure it in place with the two screws.
5. Re-attach the lamp cover.
6. Tighten the lamp cover screw.
7. Reset the lamp timer.
1. Press Left button, Menu button, and Up button within one second on the
control keypad or remote control...

Check These Items














Check that the power cable is plugged in and that power switch on the
side of projector is switched on, and power button on the projector
control keypad or remote control is pressed on.
Check that the projector is on.
Use the menu to select the source (Composite video, S-Video,
Component video, Analog RGB, Component video or DVI). See page 25.
Ensure the cables are connecting correctly.
Use the menu to adjust the brightness and contrast. See page 21. Or...

6.1 Specifications
Model Number: Vivid Red
Display Technology 0.9 LCOS D-ILA x 3
Resolution SXGA (1365 x 1024)
Projection Lamp 200W UHP lamp, 1500 hours typical
Brightness 1100 ANSI lumens typical
Brightness Uniformity 85% typical
Contrast Ratio 500:1 (full on / full off) typical
Aspect Ratio Standard 4:3 and wide screen 16:9
Projection Lens (Zoom) F=2.5, f=36 - 45mm, zoom ratio1.3, Manual Focus /Manual Zoom
Screen Size 30 - 300
Throw Distance 1.2 - 16m
Keystone Correction 15 degree
Digital Zoom 10X...

Aspect ratio
Brightness
Contrast (ratio)
Component Video
Composite Video
Keystone
Lumen
NTSC
OSD
PA L
Pixel
Resolution
RS-232
S-Video
SECAM
Tint
Zoom
7. Appendices
7.1 GlossaryThis appendix defines the specific terms used in this manual.
The ratio of the width of an image to its height.
The balance of light and dark shades in an image.
The degree of difference between the lightest and darkest areas of the
image.
A high-end digital(YCrCb) and analog(YPrPb) component video signal.
The output of
A...

Image
Advanced
Options
Utilities
Audio
Source
Standard
OSD
Language
BNC
Image Orientation
Rear ProjectionFill Aspect 1:1
Normal Anamorphic Zoom WideEnglish German French Spanish Chinese
RGB YUV
Upright Inverted
On Off
Brightness
Contrast
H Position
V Position
Phase
Frequency
RGB Image Signals
Sharpness
User Red
User Green
User Blue
ScalingRGB Image Signals
Brightness
Contrast
H Position
V Position
Color
Tint
Detail
Video Image Signals
Sharpness
User Red
User Green
User Blue
Scaling
Video Image Signals...

0 50 100 150
200 250 300
0 102030405060
Proj ecti on D i s tance (ft) Screen
wi dth (i n)
7.3 Throw Distance
Screen Size
(inch)
30
40
60
80
100
150
200
250
300
Screen Size
Projection Distance (L)
Height Width
(cm)
76
102
152
203
254
381
508
635
762(inch)
18
24
36
48
60
90
120
150
180(cm)
46
61
91
122
152
229
305
381
457(inch)
24
32
48
64
80
120
160
200
240(cm)
61
81
122
163
203
305
406
508
610(m)
1.2-1.6
1.6 2.1
2.4 3.2
3.2 4.3
45.3
68
8 10.7
10 13.3
12 16-
-
-
-
-
-
-
-
(ft)
3.9- 5.12
5.12- 6.9...

7.4 Serial Communication Cable
Appendices
Projector
(female port)
Projector
(female port)Computer / Switcher
(male)
Male / Female
adapter (null modem)
Computer / Switcher
(male)
Standard RS-232 cable, with 9-pin D connectors
Standard RS-232 cable, 9-pin male D connector to 25-pin female
36
NOTE:Standard RS-232 cable pin 9 is open.
Male / Female
adapter (null modem)