Projector Christie Vivid Red User Manual

Installation & Setup
9
Connecting to a Video / Laser Disk / DVD Player
COMPUTER
AUDIO OUTL- AUDIO -R VIDEO
MOUSE
RS232CS-VIDEO
To S-VIDEO terminal
(used to connect
equipment with S-Video
output terminal)
Laser disk player Video deck DVD player
S-Video terminal cable
(supplied)
To S-Video
output terminalAV cable
(supplied)
To video/audio
output terminal To VIDEO & AUDIO
L/R terminal
(this connection
enables image and
sound output) To AUDIO terminal
(Sound can be
produced) To B/B-Y, G-Y, R/R-Y
terminal...

An external speaker system can connect to the projector to gain maximum
benefit from the projectors built-in sound function.
Turn off the projector and speaker system if they are on.
Connecting the stereo audio cables miniplug to the projectors Audio
Out jack.
Connecting the other end of the stereo audio cable to the dual male RCA
to female adapter.
Connecting the RCA plugs to the external speakers. Insert the cables
red plug into the Audio R jack, and the white plug into the Audio L jack.






NOTE:The...

The remote control can be used as a wireless mouse by connecting the
projector mouse port to the computer mouse port.
Connecting the big end of the PS/2 mouse cable (9 pin) to the projector
mouse port.
Connecting the small end of the PS/2 mouse cable (6 pin) to the
computers mouse port.
For a Macintosh computer, connect the USB mouse or PS/2 mouse.
Connecting the Mouse:
How to Use the Remote Control as a Wireless Mouse:















Right Mouse button
Left Mouse button
Moving the Cursor
Select Item...

Rear/ Side Features
Height adjusterAdjustment levers
Speaker I/O terminal panel
Remote sensor
Control keypad
Focus ring Lens
Remote sensor
Speaker
Handle
Main power switch
AC input
Adjustment levers
Height adjuster
Zoom lever
Ventilation
Height adjuster
3.1 Projector BasicsFront/ Side Features
3.Operation
Security Lock *
12
Security Lock Note:
The projector can connect to a commercially available security cable
(Kensingtons). 

Bottom Features
Rear foot
Air filter (small)
Air filter (large)
Lamp cover
Lamp cover screw
1. Lamp Indicator
2. Power Button & Power Indicator
3. Source Button
4. Menu Button
5. Up, Down, Left, Right ButtonUse this button to turn the power on and
off when the main power switch on the
side of the projector is switched on and
the projector is in standby mode.
Use the button to select a proper
source such as PC, VCR, DVD player,
etc.
Displays the menu.
Use Up, Down to select the menu item
you wish to...

I/O Terminal Features
DVICOMPUTER
R/R-Y G-Y
B/B-Y
H/C.SYNC. V.SYNC.
PC AUDIO
AUDIO OUTL- AUDIO -R VIDEO
MOUSE
RS232CS-VIDEO
Operation
14 

Before turning on the projector, make sure the video source is turned on and
the lens cap is removed. Connect the power cord to the projector.
1. Turn on the main power switch on the side of the projector, the projector
will go into its standby mode and the power indicator will glow orange.
2. Press the Power button on the projector control keypad or on the remote
control, the power and lamp indicator will glow green and the projector
will be ready to use.
1. Press the Power button on the projector...

3.3 Basic Operation
Operation
Adjusting the Tilt Feet
1. Lift the front edge of the projector.
2. Press the adjustment levers on the front of the projector and hold the levers.
3. Lower the front of the projector to desired height and release the lever to
lock the tilt feet.
4. Fine-adjust the height, use the height adjusters on the front of the projector.
4
2
2
3
1
1. Open the battery compartment cover on
the back of the remote control unit in the
direction shown.
2. Insert two size AAA batteries,...

Selecting the Desired Image
Adjusting the Focus
Adjusting the Zoom of the Image
Press the Video button on the remote control to cycle through the video
inputs.(Composite, S-Video, Component)
Press the Data button on the remote control to cycle through the RGB
graphics inputs. (RGB, Component, DVI)
Press the Source button on the control keypad to start source auto scan
through composite Video, S-Video, component video (if connecting BNC
with video source), Analog RGB, component RGB (if connecting BNC...

Correcting the Keystone Distortion
Adjusting the Volume
Press the keystone button, And adjustment scale is displayed.
Press button to adjust the upper part of the image;
Use Vol- button to correct the lower part of the image.
Press the Vol+/ Vol- buttons on the remote control to increase or decrease
the volume.Vol+
MENUPOWER
LASER
DATAKEYSTONEZOOM
AUTO
VIDEOFREEZE
LMRM
DOWN UP
Keystone
button
Operation
LEFT
RIGHT
VOL-
VOL+
18
Zoom
button
Up, Down,
Right, Left
buttons
LAMP
SOURCE
MENUPOERWMENUPOWER
LASER...