Projector Christie Rpmsp D180u User Manual

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-9020-100245-03 Rev. 1 (11-2010)
3. Press one of the input keys on the remote to select and display the image for the source connected in Step 
4. 
NOTE: For more information on the keys available on the remote and their function, refer to Section Section 3 
Operation.
NOTE: To protect the lamp, the projector enforces a 60 second wait period from the time the projector is 
powered down and back up again.
Step 6 Adjusting the...

2-10RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
Step 8 Adjust software to optimize image 
NOTES: 1) Refer to Section 3 Operation for details on accessing and adjusting individual settings. 
2) Unless otherwise indicated, instructions apply to all projector models in stand-alone or multi-projector 
configurations.
1. Display an external signal.
2. Select a lamp operation mode. Perform all setups in the mode you select.
3. Select Image...

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-11020-100245-03 Rev. 1 (11-2010)
6. Enable Broadcast Key in the Communications menu – this enables you to switch between communicat-
ing with one or all projectors when connected serially.
7. Select Auto Setup to allow the projector to choose the best possible settings for the selected input signal.
8. Change Resize Presets if you want the image displayed at any other resolution than native.
9. Adjust Pixel Phase and Pixel...

2-12RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
FIGURE 2-11 INPUT PANEL
RGB signals (5 BNCs) 
INPUT 1 has 5 BNCs for connecting a variety of sources. A typical connection would be to an RGB source such 
as a PC, Mac, Sun, SGI and others. This projector supports multiple sync types: sync-on-green, composite 
sync, and separate H & V syncs.
Connect the 
SYNC BNC input(s). H & V syncs may be connected in any order, the projector will auto detect...

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-13020-100245-03 Rev. 1 (11-2010)
FIGURE 2-12 CONNECTING RGB
YPbPr signals 
Connect a YPbPr signal (component video) to 
INPUT 1 or INPUT 2 as shown in figure 2.14.
NOTES: 1) If the projector fails to recognize a YPbPr signal, specify the Color Space option within the Image 
Settings menu. See 3.5 Adjusting the Image.
FIGURE 2-13 CONNECTING YPBPR
DVI Digital Video
Use the DVI-I connector at 
INPUT 2 to connect either analog or...

2-14RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
FIGURE 2-14 CONNECTING ANALOG OR DIGITAL VIDEO DEVICES
Composite and S-Video 
INPUT 3 and INPUT 4 provide simultaneous connection of both a composite video source (INPUT 3) and an S-
Video source (
INPUT 4). 
FIGURE 2-15 CONNECTING COMPOSITE / S-VIDEO
Extra Video 
To use an extra video source in addition to the video source(s) connected at input 3 or input 4, connect either a 
Composite or...

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-15020-100245-03 Rev. 1 (11-2010)
Optional Inputs
Optional input modules allow you to increase your total number of inputs to accommodate different signal 
types, whether analog or digital. Install in the area labeled 
INPUT 5. Options include:
• RGB 500 Input Module
• RGB 400 Active Loop Thru Input Module
• RGB 400 Buffered Amplifier Input Module
• PC250 Analog Input Module
• Serial Digital Input Module
• DVI Input Module
•...

2-16RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
Connecting RS-422
To control the projector with a computer or other devices with RS-422 capability, connect an RS-422 serial 
communication cable between the computer and the RS-422 port on the projector. RS-422 is better suited for 
serial communication over long distances than RS-232 communication. 
Use the RS-422 port only if your device has RS-422 capability. Consult the literature provided...

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-17020-100245-03 Rev. 1 (11-2010)
2.4.4 Connecting Multiple Projectors
RS-232 Network
To connect multiple projectors in a network with serial communication, connect the controlling source to the 
RS-232 IN connector of the first projector in the network. Then take another serial communication cable and 
connect one end to the RS-232 OUT connector and the other end to the RS-232 IN connector of the next 
projector. Continue this...

2-18RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
Communication parameters such as baud rate must be set to match the particular controlling device before 
connecting as a network—refer to the documentation that came with your controlling device in order to 
determine the proper baud rate. See 3.6, Adjusting System Parameters and Advanced Controls if you need help 
changing the projector baud rate. Set the Network Routing to “RS-232 and RS-422...