Home > Christie > Projector > Projector Christie Rpmsp D180u User Manual

Projector Christie Rpmsp D180u User Manual

Here you can view all the pages of manual Projector Christie Rpmsp D180u User Manual. The Christie manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 11

Section 1: Introduction
RPMX/RPMSP-D132U & RPMSP-D180U User Manual1-3020-100245-03 Rev. 1 (11-2010)
1.5 Purchase Record and Servicing
Christie’s factory and dealer service network is available to diagnose and correct projector malfunctions. 
Service manuals and updates are available to service technicians for all projectors.
If you encounter any problems with the projector and require assistance, contact your dealer or Christie Digital 
Systems. Fill out the information in the table below and keep with...

Page 12


				            

Page 13

RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-1020-100245-03 Rev. 1 (11-2010)
2 Installation and Setup
Use this section to install and setup your projector. Complete these steps:
Step 1 – Unpack the projector.
Step 2 – Select and modify the projector’s configuration according to the intended application: lens-vertical 
(90 degree) or lens-horizontal (0 degree) projection.
Step 3 – Calculate throw distance if necessary. Position and mount the projector. 
Step 4 – Connect sources.
Step 5 – Turn the projector...

Page 14

2-2RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
2.1.2 Ambient Lighting 
The high brightness of this projector is well suited for locations where ambient lighting might be considered 
less than ideal for projection. A typical room with ceiling lights and windows rarely requires special attention. 
If light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image, 
the contrast ratio in your image...

Page 15

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-3020-100245-03 Rev. 1 (11-2010)
NOTE: An L-shaped bracket, used to change the projector’s configuration, is shipped loosely in the box with 
the projector. Set this aside for future use.
Verifying all cable connections are secure. Connect any loose cables. See Figure 2-1 Internal Cable 
Connections.
 Remove the lock screw located on the mechanical lamp changer. See Figure 2-2 Remove Lamp Changer 
Lock Screw. This screw is used...

Page 16

2-4RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
Step 2 Modifying projector configuration (if required)
To use your projector for lens-horizontal projection then you must change its configuration. The L-shaped 
bracket and M6 screws shipped with the projector are needed to complete this configuration change.
1. Unplug projector from AC.
2. Disconnect all cables between the light engine and electronics module. All disconnects must be made on...

Page 17

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-5020-100245-03 Rev. 1 (11-2010)
7. Place the light engine in the lens-horizontal position on the L-shaped bracket and adjuster base. Align the 
mounting holes between the configuration bracket and light engine and secure using the (6) additional M6 
screws provided with the projector. 
90°
FIGURE 2-5 RE-POSITION LIGHT ENGINE 

Page 18

2-6RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
8. Reconnect all cables disconnected previously in step 2. Refer to Figure 2-1 Internal Cable Connections.
Step 3 Calculating throw distance, position and mount projector 
Throw Distance
For lens-horizontal configurations, throw distance is measured from the center of the auxiliary mounting holes 
in the tray to the screen. Use the appropriate formula for your projector model when calculating....

Page 19

Section 2: Installation and Setup
RPMX/RPMSP-D132U & RPMSP-D180U User Manual2-7020-100245-03 Rev. 1 (11-2010)
For lens-vertical configurations, where a first surface mirror is used to shorten the distance between the 
projector and screen by folding the optical path, throw distance is a little more difficult to calculate, as there are 
many variables to consider.
FIGURE 2-7 THROW DISTANCE FORMULA FOR LENS-HORIZONTAL CONFIGURATION
FIGURE 2-8 THROW DISTANCE FORMULA FOR LENS-VERTICAL CONFIGURATION 

Page 20

2-8RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Section 2: Installation and Setup
Lifting and transporting the projector 
Use the handles on either side of the light engine to lift the projector. Use a stable cart to transport the projector.
Mounting 
Refer to the drawings provided for your specific projector model in Appendix Section B Dimensions & 
Mounting Information for mounting hole locations and other technical information.
 Mount the projector to a sturdy, flat surface...
Start reading Projector Christie Rpmsp D180u User Manual

Related Manuals for Projector Christie Rpmsp D180u User Manual

All Christie manuals