Planar Pr9030 Projector User Manual

							69
Troubleshooting
Regarding the indicator lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP  
indicator have the meanings as described in the table below. Please follow the 
instructions within the table. If the same indication is displayed after\
 the remedy, 
or if an indication other than the following is displayed, please contac\
t your dealer 
or service company.
(Continued on next page)
POWER 
indicatorLAMP 
indicatorTEMP 
indicator Description
Lighting
In Orange Turned
off Turned
off
The projector is in a standby state.
Please refer to the section “Power On/Off”.
Blinking
In Green Turned
off Turned
off
The projector is warming up.
Please wait.
Lighting
In Green Turned
off Turned
off
The projector is in an on state.
Ordinary operations may be performed.
Blinking
In Orange Turned
off Turned
off
The projector is cooling down.
Please wait.
Blinking In Red (discre-
tionary) (discre-
tionary)
The projector is cooling down. A certain error 
has been detected.
Please wait until the POWER indicator finishes 
blinking, and then perform the proper measure using 
the item descriptions below.
Blinking In Red or
Lighting In Red Lighting
In Red Turned
off
The lamp does not light, and there is a 
possibility that interior portion has become 
heated.
Please turn the power off, and allow the projector to 
cool down at least 20 minutes. After the projector has 
sufficiently cooled down, please make confirmation of 
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy, 
please change the lamp referring to the section “Lamp”.
Blinking In Red or
Lighting In Red Blinking
In Red Turned
off
The lamp cover has not been properly fixed. 
Please turn the power off, and allow the projector to 
cool down at least 45 minutes. After the projector has 
sufficiently cooled down, please make confirmation 
of the attachment state of the lamp cover. After 
performing any needed maintenance, turn the power 
on again. If the same indication is displayed after 
the remedy, please contact your dealer or service 
company. 
						

							70
Troubleshooting
• When the interior portion has become overheated, for safety 
purposes, the power source is automatically turned off, and the indicator lamps 
may also be turned off. In such a case, press the “” (OFF) side of the power 
switch, and wait at least 45 minutes. After the projector has sufficiently cooled 
down, please make confirmation of the attachment state of the lamp and lamp 
cover, and then turn the power on again. NOTE
POWER 
indicatorLAMP 
indicatorTEMP 
indicator Description
Blinking In Red or
Lighting In Red Turned
off Blinking
In Red
The cooling fan is not operating.
Please turn the power off, and allow the projector to 
cool down at least 20 minutes. After the projector has 
sufficiently cooled down, please make confirmation 
that no foreign matter has become caught in the fan, 
etc., and then turn the power on again.
If the same indication is displayed after the remedy, 
please contact your dealer or service company.
Blinking In Red or
Lighting In Red Turned
off Lighting
In Red
There is a possibility that the interior portion 
has become heated.
Please turn the power off, and allow the projector to 
cool down at least 20 minutes. After the projector has 
sufficiently cooled down, please make confirmation of 
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy, 
please set FAN SPEED of the SERVICE item in the 
OPTION Menu to HIGH.
Lighting
In Green Simultaneous
blinking in  Red
It is time to clean the air filter.
Please immediately turn the power off, and clean or 
change the air filter referring to the section “Air Filter”. 
After cleaning or changing the air filter, please be sure 
to reset the filter timer. After the remedy, reset the 
power to ON.
Lighting
In Green Alternative
blinking in  Red
There is a possibility that the interior portion 
has become overcooled.
Please use the unit within the usage temperature 
parameters (5°C to 35°C). After the treatment, reset 
the power to ON.
Blinking in  Green for approx. 3  seconds Turned
off Turned
off
At least 1 “Power ON” schedule is saved to the 
projector.
(Please refer to the User’s Manual-Network Guide: 
Schedule Settings for more information.)
Regarding the indicator lamps (continued) 
						

							71
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
►Never use the projector if abnormal operations such as smoke, 
strange odor, excessive sound, damaged casing or elements or cables, penetration 
of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the 
power switch and then disconnect the power plug from the power outlet. After making 
sure that the smoke or odor has stopped, contact your dealer or service \
company.WARNING
(Continued on next page)
Phenomenon Cases not involving a machine defectReference
page
Power does not  come on.
The electrical power cord is not plugged in.Correctly connect the power cord. 12
The power switch is not set to the on position.Set the power switch to [ | ] (On).16
The main power source has been interrupted during 
operation such as by a power outage (blackout), etc.
Please turn the power off, and allow the projector to cool 
down at least 2 minutes, then turn the power on again. 16
Either there is no lamp and/or lamp cover, or either 
of these has not been properly fixed.
Please turn the power off, and allow the projector to cool down at 
least 45 minutes. After the projector has sufficiently cooled down, 
please make confirmation of the attachment state of the lamp and 
lamp cover, and then turn the power on again.63
Neither sounds
nor pictures are outputted.
The signal cables are not correctly connected.Correctly connect the connection cables. 10
Signal source does not correctly work.Correctly set up the signal source device by referring to the 
manual of the source device. –
The input changeover settings are mismatched.Select the input signal, and correct the settings.
17, 18
The BLANK function for pictures and the MUTE function for 
sounds are working.
AV mute may be active. Refer to the item “Sound does not come out” and “No 
pictures are displayed” on the next page to turn off the MUTE and BLANK functions.
17, 22
1.Before requesting repair, please check in accordance with the 
following chart.  This operation sometimes resolves your problem.
 
If the situation cannot be corrected, 
2.The projector’s microprocessor may need to be reset.  
Please push the Shutdown switch by using a pin or similar and the projector will be turned off immediately.
Before turning it again, wait at least 10 minutes to make the projector cool down enough.
3.Some setting may be wrong. Please use the FACTORY RESET function of the SERVICE item in the 
OPTION Menu (
48) to reset all settings to factory default. 
Then, if the problem is not removed after the remedy, please contact your dealer or service company. 
						

							72
Troubleshooting
Phenomena that may be easily mistaken for machine defects (continued)
(Continued on next page)
PhenomenonCases not involving a machine defectReference
page
Sound does not  come out.
The signal cables are not correctly connected.Correctly connect the audio cables. 10
The MUTE function is working.Restore the sound pressing the MUTE or VOLUME button 
on the remote control. 17
The volume is adjusted to an extremely low level.Adjust the volume to a higher level using the menu function 
or the remote control.17
The AUDIO setting is not correct.Correctly set the items in the AUDIO Menu.
38
The audio on your HDMI equipment is not set to Linear PCM.The HDMI input on this projector supports Linear PCM audio 
only. Check the audio setting on your HDMI equipment. 11
The audio on the HDMI input is muted.Change the audio setting in the AUDIO Menu.
38
The digital audio in HDMI signal does not work well.Use the analogue audio, connecting either an RCA audio 
cable or stereo mini cable.10
No pictures are  displayed.
The lens cover is attached.Remove the lens cover. 3, 16
The signal cables are not correctly connected.Correctly connect the connection cables. 10
The brightness is adjusted to an extremely low level.Adjust BRIGHTNESS to a higher level using the menu 
function or the remote control.26
The computer cannot detect the projector as a plug and play monitor.Make sure that the computer can detect a plug and play 
monitor using another plug and play monitor. 11
The BLANK screen is displayed.Press the BLANK button on the remote control.22
No pictures 
or disturbed  pictures are 
displayed on 
HDMI input.
The HDMI cable is not correctly connected.Correctly connect the HDMI cable. 10
Your HDMI equipment is not compatible with the projector
This projector can be connected with another equipment 
that has HDMI or DVI connector, but with some equipment 
the projector may not work properly.  11
Your HDMI equipment and the projector are not harmonized.Turn off the both equipment, and turn on them again
–
The signal format on the HDMI is not supported.Check the video setting on your HDMI equipment.11 
						

							73
Troubleshooting
Phenomena that may be easily mistaken for machine defects (continued)
• Although bright spots or dark spots may appear on the screen, this 
is a unique characteristic of liquid crystal displays, and it does not c\
onstitute or 
imply a machine defect. NOTE
Phenomenon Cases not involving a machine defectReference
page
Video screen
display freezes. The FREEZE function is working.
Press the 
FREEZE button to restore the screen to normal.
21
Colors have a faded- out
appearance, or Color tone is  poor.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR 
TEMP, COLOR, TINT and/or COLOR SPACE settings, 
using the menu functions. 26, 28, 
32
COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to AUTO, RGB, 
SMPTE240, REC709 or REC601.  32
Pictures appear  dark.
The brightness and/or contrast are adjusted to an 
extremely low level.
Adjust BRIGHTNESS and/or CONTRAST settings to a 
higher level using the menu function. 26
The WHISPER function is working.
Select NORMAL for the WHISPER item in the SETUP 
Menu.
26, 37
The lamp is approaching the end of its product 
lifetime.
Replace the lamp.63, 64
Pictures appear blurry.
Either the focus and/or horizontal phase settings are 
not properly adjusted.
Adjust the focus using the focus ring, and/or H PHASE 
using the menu function. 19, 31
The lens is dirty or misty.
Clean the lens referring to the section “Caring for the lens”.
67
Pictures are  trembling.
The exhaust ventilation holes at front is blocked by 
some objects.
Remove any objects from front side of the projector. 4 
						

							74
Warranty and after-ser vice / Specifications
Warranty and after-service
If a problem occurs with the equipment, first refer to the “Troubleshooting” and 
run through the suggested checks. If this does not resolve the problem, \
please 
contact your dealer or service company. They will tell you what warranty condition 
is applied.
Specifications
• These specifications are subject to change without notice.
NOTE
Item Specifications
Product name Liquid crystal projector
Liquid
Crystal
Panel Panel size
1.9cm (0.75 type)
Drive system TFT active matrix
Pixels 1,024,000 pixels (1280 horizontal x 800 vertical)
Lens Zoom lens F=1.7 ~ 1.9  f=24 ~ 29 mm (approx.)
Lamp 275W UHB
Audio output 4W x 4
Power supply AC 100-120V/5.0A, AC220-240V/2.1A
Power consumption 460W
Temperature range 5 ~ 35°C (Operating)
Size 418 (W) x 139 (H) x 319 (D) mm
(Not including protruding parts)
* Please refer to the following figure.
Weight (mass) 7.1kg (approx.)
Ports
RGB1   ..................................................... D-sub 15 pin mini x 1RGB2 G/Y, B/CB/PB, R/CR/PR, H, V ............................. BNC x 5S-VIDEO  ...................................................... mini DIN 4 pin x 1VIDEO  ........................................................................\
 RCA x 1Y, CB/PB, CR/PR (component video)  ............................ RCA x 3HDMI  ........................................................................\
 HDMI x 1AUDIO IN1 ....................................................... Stereo mini x 1AUDIO IN2 .......................................................Stereo mini x 1AUDIO IN3 R/L  ........................................................... RCA x 1AUDIO IN4 R/L  ........................................................... RCA x 1RGB OUT ............................................... D-sub 15 pin mini x 1AUDIO OUT  ..................................................... Stereo mini x 1USB  ...................................................................... USB (B) x 1REMOTE CONTROL  ....................................... Stereo mini x 1CONTROL  ....................................................... D-sub 9 pin x 1LAN ........................................................................\
.... RJ45 x 1
Optional partsLamp: 997-5465-00 
(DT00873)
Air filter: 997-5466-00 (MU05661)
* For more information, please consult your dealer. 
						

							75
Specifications
Specifications (continued)
[unit: mm]
418
319
154 139
LAN
AC IN
I   O
VIDEO
CONTROL
AUDIO IN1
AUDIO IN2
AUDIO OUT
RGB
 OUTRGB1
RGB2
HDMI
 R             L      R           L
     AUDIO IN3        AUDIO IN4
CB/PBY CR/PRB/CB/PBR/CR/PRG/Y
HVUSBREMOTE 
CONTROL
   
S-VIDEO 
						

							Planar Systems, Inc .
Corporate Headquarters
1195 NW Compton Drive
Beaverton, OR 97006-1992
Planar Customer Support
Telephone:
US: 1-866-PLANAR1 (866) 752-6271
Outside US: (503) 748-5799
E-mail: [email protected]
Online Technical Library: http://www.planar.com/support
24/7 Technical Support
© 2008 Planar Systems, Inc. Planar is a registered trademark of Plana\
r Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice.020-0851-00A