Planar Pr9030 Projector User Manual

							39
SCREEN Menu
SCREEN Menu
From the SCREEN Menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or 
ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
Item Description
LANGUAGE
Using the ▲/▼ buttons switches the OSD (On Screen Display) language.
�
TÜRKÇE �
POLSKI �
SUOMI �
ENGLISH � FRANÇAIS � DEUTSCH � ESP
AÑOL � ITALIANO
�
NORSK �
NEDERLANDS �
POR TUGUÊS
�
РУ ССКИЙ  � SVENSKA  � ¿—µ � 4P¨
[ � 1T
[ � ãÄ.† 
MENU POSITION Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the MENU button on the remote control 
or keep no operation for about 10 seconds.
BLANK Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
 
(
22). It is displayed by pressing the BLANK button on the remote 
control.
MyScreen  ó ORIGINAL 
ó BLUE 
ó WHITE 
ó BLACK
  
Feature
MyScreen Screen can be registered by the MyScreen item 
(
41).
ORIGINAL Screen preset as the standard screen.
BLUE, WHITE, 
BLACK Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the plain black screen after several minutes.
(continued on next page) 
						

							40
SCREEN Menu
SCREEN Menu (continued)
ItemDescription
START UP Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an 
unsuitable signal is detected.
MyScreen  ó ORIGINAL 
ó TURN OFF
    
Feature
MyScreen Screen can be registered by the MyScreen item 
(
41).
ORIGINAL Screen preset as the standard screen.
TURN OFF Plain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the BLANK screen  (
39) after several 
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, 
the plain black screen is instead used.
• When the TURN ON is selected to the MyScreen PASSWORD of 
SECURITY item in OPTION Menu (
 50), the START UP is fixed to 
MyScreen.
(continued on next page) 
						

							41
SCREEN Menu
SCREEN Menu (continued)
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
1.  
Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from the 
current screen.
Please wait for the target image to be displayed, and press 
the 
ENTER button on the remote control when the image is 
displayed. The image will freeze and the frame for capturing will 
appear. 
To stop performing, press the 
RESET  or ESC button on the 
remote control. 
2.   Using the ▲/▼/◄/► buttons adjusts 
the frame position.  
Please move the frame to the position 
of the image which you want to use. The 
frame may not be able to be moved for 
some input signals.  
To start registration, press the 
ENTER 
button on the remote control.
To restore the screen and return to the previous dialog, press the 
RESET  or ESC button on the remote control. 
Registration takes several minutes.  
When the registration is completed, the registered screen and the 
following message is displayed for several seconds: “MyScreen registration is finished.”
If the registration failed, the following message is displayed: “A capturing error has occurred. Please try again.” 
• This item cannot be selected for an HDMI signal.
• This function cannot be selected when the TURN ON is selected 
to the MyScreen Lock item (
 below).
• This function cannot be selected when the TURN ON is selected 
to the MyScreen PASSWORD of SECURITY item in OPTION Menu 
(
 50).
MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function.
TURN ON  ó TURN OFF
When the TURN ON is selected, the item MyScreen is locked. Use 
this function for protecting the current MyScreen.
• This function cannot be selected when the TURN ON is selected 
to the MyScreen PASSWORD of SECURITY item in OPTION Menu 
(
 50).
(continued on next page) 
						

							42
SCREEN Menu
SCREEN Menu (continued)
ItemDescription
MESSAGE Using the ▲/▼ buttons turns on/off the message function.
TURN ON  ó TURN OFF
When the TURN ON is selected, the following message function works.
“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
The indication of the input signal displayed by changing 
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the ACTIVE IRIS displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while freezing the screen by 
pressing the 
FREEZE button.
• When the TURN OFF is selected, please remember if the picture 
is freezing. Do not mistake freezing for a malfunction  (
21).
SOURCE NAME Each input port for this projector can have a name applied to it.
(1) Use the ▲/▼ buttons on the SCREEN Menu to 
select SOURCE NAME and press the ► button. The SOURCE NAME menu will be displayed.
(2) Use the ▲/▼ buttons on the SOURCE 
NAME menu to select the port to be named 
and press the ► button. Right side of the 
menu is blank until a name is specified.
The SOURCE NAME dialog will be displayed.
(3) The current name will be displayed on 
the first line. Use the 
▲/▼/◄/► buttons 
and the ENTER or INPUT  button to select and 
enter characters. The RESET  button can be 
used to erase 1 character at a time. Also if you 
move the cursor to DELETE or ALL CLEAR on 
screen and push the 
ENTER or INPUT  button, 
1 character or all characters will be erased. The 
name can be a maximum of 16 characters.
(4) To change an already inserted character, 
press the ▲ button to move the cursor to the 
first line, and use the ◄/► buttons to move 
the cursor on the character to be changed. 
After pressing the 
ENTER or INPUT  button, the 
character is selected.  Then, follow the same 
procedure as described at the item (3) above.
(5) To finish entering text, move the cursor to the 
 SAVE on screen and press the 
ENTER or INPUT  button. To revert to the 
previous name without saving changes, move the cursor to the CANCEL on 
screen and press the 
ENTER or INPUT  button.
(continued on next page) 
						

							43
SCREEN Menu
SCREEN Menu (continued)
ItemDescription
TEMPLATE Using ▲/▼ buttons switches the mode for the 
template screen. The selected template pattern 
can be displayed when the 
MY BUTTON allocated 
to the TEMPLATE function is pressed (
 46). DOT-LINE4 
ó DOT-LINE3 
ó DOT-LINE2
TEST PATTERN  ó DOT-LINE1 
						

							44
OPTION Menu
OPTION Menu
From the OPTION Menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or 
ENTER button on 
the remote control to execute the item, except for the 
items LAMP TIME and FILTER TIME. Then perform it 
according to the following table.
Item Description
AUTO SEARCH
Using the ▲/▼ buttons turns on/off the automatic signal search function.
TURN ON  ó TURN OFF
When the TURN ON is selected, detecting no signal automatically cycles 
through input ports in the following order. The search is started from the 
current port. Then when an input is found, the projector will stop searching 
and display the image. 
RGB 1 
ð RGB 2 
ð HDMI 
ð COMPONENT 
ð S-VIDEO 
ð VIDEO       
AUTO 
KEYSTONE 
Using the ▲/▼ buttons turns on/off the automatic keystone function.
TURN ON  ó TURN OFF
TURN ON : Automatic keystone distortion correction will be 
executed whenever changing the slant of the projector.
TURN OFF : This function is disabled. Please execute the AUTO 
KEYSTONE 
 EXECUTE in the SETUP Menu for automatic 
keystone distortion correction.
• When the projector is suspended from the ceiling this feature will 
not function properly so select the TURN OFF.
• This function will be unavailable when the Transition Detector is 
on 
( 53).
AUTO ON Using the ▲/▼ buttons turns on/off the AUTO ON function.
TURN ON  ó TURN OFF
When set to the TURN ON, the lamp in projector will be
automatically turned on without the usual procedure ( 16), only
when the projector is supplied with the power after the power was
cut while the lamp was on.
• This function does not work as long as the power has been
supplied to the projector while the lamp is off.
• After turning the lamp on by the AUTO ON function, if neither input
nor operation is detected for about 30 minutes, the projector is
turned off, even though the AUTO OFF function 
( 45) is disabled.
(continued on next page) 
						

							45
OPTION Menu
OPTION Menu (continued)
ItemDescription
AUTO OFF Using the ▲/▼ buttons adjusts the time to count down to 
automatically turn the projector off.
Long (max. 99 minutes)  ó Short (min. 0 minute = DISABLE)
When the time is set to 0, the projector is not turned off automatically.When the time is set to 1 to 99, and when the passed time with no-
signal or an unsuitable signal reaches at the set time, the projector 
lamp will be turned off. 
If one of the projector's buttons or the remote control buttons 
is pressed or one of the commands (except get commands) is 
transmitted to the 
CONTROL
 port during the corresponding time, 
projector will not be turned off.
Please refer to the section “Turning off the power”
 ( 16).
LAMP TIME The lamp time is the usage time of the lamp, counted after the last 
resetting. It is shown in the OPTION Menu.
Pressing the 
RESET
 button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the lamp time, select the RESET using the ▲ button.
RESET   CANCEL
• Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
• For the lamp replacement, see the section "Lamp"  (
63, 64).
FILTER TIME The filter time is the usage time of the air filter, counted after the last 
resetting. It is shown in the OPTION Menu.
Pressing the 
RESET
 button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the filter time, select the RESET using the ▲ button.
RESET   CANCEL
• 
Please reset the filter time only when you have cleaned or replaced 
the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section "Air filter"  (65).
(continued on next page) 
						

							46
OPTION Menu
OPTION Menu (continued)
ItemDescription
MY BUTTON This item is to assign one of the following function to 
MY BUTTON 1 and 2 on the remote control (
6).Choose 1 or 2 on the MY BUTTON menu using the ◄/► button first. Then 
using the ▲/▼ buttons sets one of the following functions to the chosen button.
• RGB1: Sets port to RGB1.
• RGB2: Sets port to RGB2.
• HDMI: Sets port to HDMI.
• COMPONENT: Sets port to COMPONENT (Y, CB/PB, CR/PR).
• S-VIDEO: Sets port to S-VIDEO.
• VIDEO: Sets port to VIDEO.
•   INFORMATION:  Displays  the  INPUT  -INFORMATION-  (48)  or 
NETWORK -INFORMATION- ( 61) or nothing
.
•   
AUTO KEYSTONE  : Performs automatic keystone distortion 
correction ( 36).
•   MY MEMORY: Loads one of adjustment data stored  (29). When more than one data are saved, the adjustment  
changes every time the MY BUTTON is pushed.When no data is saved in memory, the dialog "No 
saved data" appears.
When the current adjustment is not saved to 
memory, the dialog as shown in the right appears.
If you want to keep the current adjustment, please press  
the ◄ button to quit. Otherwise loading a data will overwrite the current adjusted condition.
• ACTIVE IRIS: Changes the active iris mode.
• PICTURE MODE: Changes the PICTURE MODE (25).
•  FILTER RESET: Displays the filter time reset confirmation dialogue ( 45)
.• AV MUTE : Turns the picture and audio on/off.
•   TEMPLATE: Makes the template pattern selected to the 
TEMPLATE item
 (

43) appear or disappear.
•   PbyP  SWAP:  Swaps  the  picture  of  right  side  with  left  side  in  the 
PbyP mode (
 23).
• MY IMAGE: Displays the MY IMAGE menu ( 60).
MY SOURCE This item is to assign an input signals to 
MY SOURCE / DOC. CAMERA
 button on the remote control  (6, 18).
Using the ▲/▼ buttons sets one of the following input 
signal.
 RGB1  ó RGB2 
ó HDMI VIDEO 
ó S-VIDEO 
ó COMPONENT
SERVICE Selecting this item displays the SERVICE menu.
Select an item using the ▲/▼ buttons, and press the ► button or 
the 
ENTER button on the remote control to execute the item.
FAN SPEED ó AUTO ADJUST ó GHOST ó FILTER MESSAGE ó LENS TYPE FACTORY RESET ó INFORMATION ó REMOTE FREQ. ó REMOTE RECEIV. ó KEY LOCK
FAN SPEED
Using the ▲/▼ buttons switches the rotation speed 
of the cooling fans. The HIGH is the mode for use at 
highlands etc. Note that the projector is noisier when 
the HIGH is selected.
HIGH  ó NORMAL
(continued on next page) 
						

							47
OPTION Menu
OPTION Menu (continued)
ItemDescription
SERVICE
(continued) AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. 
When the DISABLE is selected, the automatic 
adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
      
FINE: Finer tuning including H.SIZE adjustment.
FAST:  Faster tuning, setting H.SIZE to prearranged data for the input signal.
• Depending on conditions, such as input image, signal cable to the projector, 
environment around the projector, etc., the automatic adjustment may not 
work correctly.  In such a case, please choose DISABLE to disable the 
automatic adjustment, and make adjustment manually.
GHOST
1.  Select a color element of ghost using the ◄/► buttons. 2.  Adjust the selected element using the ▲/▼ buttons to 
disappear ghost.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for the interval to 
show the message for cleaning up the air filter. 
500h  ó 1000h 
ó 1500h 
ó 2000h 
ó TURN OFF
After choosing an item except TURN OFF, the message 
“REMINDER *** HRS PASSED AFTER THE LAST FILTER 
CHECK” will appear after the timer reaches the interval time 
set by this feature
 ( 68). When the TURN OFF is chosen, the message will not appear. 
Utilize this feature to keep the air filter clean, setting the suitable time according 
to your environment of this projector.
• Please check and clean the air filter periodically, even if there is no 
message. If the air filter becomes to be blocked by dust or others, 
the internal temperature will rise, which could cause malfunction, or 
reduce the lifetime of the projector.
•
 Please be careful with the operating environment of the projector 
and the condition of the air filter.
LENS TYPE
Select the lens type currently used using the ▲/▼ buttons. 
1  ó  2 
ó 3 
ó 4 
ó 5
Please select one of them referring to the following.
1: for a standard lens (Type NL-600)
2: for a fixed short throw lens (Type FL-601)
3: for a short throw lens (Type SL-602)
4: for a long throw lens (Type LL-603)
5: for an ultra long throw lens (Type UL-604)
• This setting has an influence on the keystone distortion etc.
• About the optional lens, ask you dealer.
(continued on next page) 
						

							48
OPTION Menu
OPTION Menu (continued)
ItemDescription
SERVICE
(continued) KEY LOCK
Using  the  ▲/▼  buttons  turns  on/off  the  key  lock  feature.  When 
TURN  ON  is  selected,  the  buttons  on  the  projector  except  the 
STANDBY/ON button are locked.
TURN ON  ó TURN OFF
• Please use to avoid a mischief and touching accidentally. This 
function does not have any effect on the remote control.
REMOTE RECEIV.
(1) Select a remote sensor using the ▲/▼ button. 1:FRONT  ó 2:TOP 
ó 3:REAR
         
(2) Switch it using the ENTER or INPUT  button.
¨  (off) 
ó 
þ  (on)
• A sensor cannot be turned off when the other  
two are off. Always at least one sensor is on.
REMOTE FREQ.
Use the ▲/▼ button to change the Projector's remote sensor 
setting (
 14).
1:NORMAL  ó 2:HIGH
Items with a checkmark are on. The factory 
default setting is for both 1:NORMAL and 
2:HIGH to be on. If the remote control does 
not function correctly, set the this to either only 
1 or only 2 as described in Remote Control 
Settings (
 14).
Neither can be turned off at the same time.
INFORMATION
Selecting this item displays a dialog titled “INPUT-INFORMATION-”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• The “SCART RGB” message means the 
COMPONENT  port 
is working as a SCART RGB input port. Please refer to the 
COMPONENT item in INPUT Menu
 ( 33).
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to TURN ON, the MY TEXT 
is displayed together with the input information in the INPUT-
INFORMATION- box.
 ( 55)
FACTORY RESET
Selecting RESET using the button ▲ performs this function. By 
this function, all the items in all of menus will collectively return to\
 
the initial setting. Note that the items LAMP TIME, FILTER TIME, 
LANGUAGE, SECURITY and NETWORK settings are not reset. RESET   CANCEL
(continued on next page)