Philips Hts3578 User Manual

							21
8 Press     
 SETUP 
 to exit the menu. 
9  You can now turn on the progressive scan 
mode on the T V.
Note
  During play, when progressive scan mode is on   •
for both this Home Theater System and the 
T V, distor ted picture may display. Turn off the 
progressive scan feature on both this Home 
Theater System and the T V.
   
 
 
 
 
Turn on Progressive Scan
 
 
If the TV suppor ts progressive scan output, you 
can connect this Home Theater System and the 
TV using component video connection. (see 
‘Connect video cables’ > ‘Option 2: Connect to 
the component video jack’).
1  Turn on the T V and ensure that the T V 
progressive scan mode is deactivated (see 
the T V user manual).
2  Switch the T V to the correct viewing 
channel for this Home Theater System.
3 Press  DISC 
.
4 Press   
 
 SETUP 
.
5 Press   
 to select  [Video Setup] 
 in the 
menu, then press  
  .
6 Select  [Progressive] 
 >  [On] 
, then press 
  OK 
.
   
 
 
A warning message is displayed.   »
7  To proceed, select  [Ok] 
 and press  OK 
.
   
 
 
The progressive setup is complete.   »
Note
 
If a blank /distor ted screen is displayed, wait for   •
15 seconds for the auto recover.
   
If no picture displayed, turn off the progressive 
  •
scan mode as follows: 1) Press   
 to open 
the disc compar tment. 2) Press  
  . 3) Press 
  AUDIO SYNC 
.
Video Setup
Picture Setting
Closed Caption HDMI Setup TV Display TV System
Screen Fit
ProgressiveOn
Off
EN
Get started
English
 
						

							22
   
 
 
2 Press   
  
 to change the volume level, 
then press  OK 
.
   
 
 
The test tone is emitted from the    »
speaker.
   
 
 
 
 
 
 
Repeat the above setting for other  • 
speakers until all the speakers output 
level sounds equally balance.
   
 
 
To exit the menu, press   • 
 
 
 SETUP 
.
 
 
  
 
 
 
 
 
To set the output delay time (center and rear 
speakers only) 
 
 
  
 
 
 
 
1 Select  [Speakers Delay] 
 in the menu, 
then press  
  .
 
 
  
 
 
 
 
2 Press   
  
 to set the delay time, then press 
  OK 
.
   
 
 
Repeat the above setting for other  • 
speakers until the sound output from 
different speakers reach the listening 
position at the same time. 
   
 
 
To exit the menu, press   • 
 
 
 SETUP 
.
 
Tip
 
Set a longer delay time if the center speaker or   •
rear speaker is closer to the listening position 
than the front speaker.
   
Allow 1ms set ting for ever y 1 foot distance 
  •
between the speaker and the listening position.
Speakers Distance Setup
Center
Rear Left
Rear Right0MS
0MS
0MS
Change speaker settings
   
Ideally, the distance between listening position 
and all the speakers should be the same. If not, 
change the speaker settings based on their 
distance from the listening position to obtain 
the best possible surround sound.
   
 
  
 
 
 
 
 
 
1 Press  DISC 
.
 
 
 
 
2 Press   
 
 SETUP 
.
 
 
 
 
3 Press   
 to select  [Audio Setup] 
 in the 
menu, then press  
  .
 
 
 
 
If the speaker setup option is not  • 
a
ccessible, press 
   twice before you 
press  
   
 SETUP 
.
 
 
  
 
 
 
 
 
 
 
To set the speakers level 
 
 
  
 
 
 
 
1 Select  [Speakers Volume] 
 in the menu, 
then press  
  .
 
 
  
CD Upsampling Speakers Delay Speakers Volume
HDMI Audio
Audio Setup
Audio Sync
Speakers Volume Setup
Front Left
Front Right
Center
Subwoofer
Rear Left
Rear Right0dB
0dB
0dB
0dB
0dB
0dB
EN
 
						

							23 EN
Use Philips EasyLink
 
 
Your Home Theater System suppor ts 
Philips EasyLink, which uses the HDMI CEC 
(Consumer Electronics Control) protocol. 
EasyLink-compliant devices that are connected 
through HDMI connectors can be controlled by 
a single remote control. 
Note
  Philips does not guarantee 10 0%   •
interoperability with all HDMI CEC devices.
1  Turn on the HDMI CEC operations on 
the T V and other connected devices. See 
T Vs/devices manual for details.
2  You can now enjoy the following Philips 
EasyLink controls.
   
EasyLink 
   
You can turn off or turn on all EasyLink 
features.
   
One-touch play  
   
When you connect your Home Theater 
System to devices that suppor t one-touch 
play, you can control your Home Theater 
System and the devices with one remote 
control. For example, when you press Play on 
your Home Theater System remote control, 
your T V automatically switches to the 
correct channel to show the DVD content. 
   
To enable One-touch play, a video disc must 
be placed in the disc compar tment before 
operation.
   
One-touch standby 
   
When you connect your Home Theater 
System to devices that suppor t standby, you 
can use your Home Theater System remote 
control to put your Home Theater System 
and all connected HDMI devices in standby 
mode. You can per form one-touch standby 
using the remote control from any of the 
connected HDMI devices.
   
System Audio Control 
   
When you connect your Home Theater 
System to HDMI CEC compliant devices, 
your Home Theater System can switch 
automatically to play audio from the 
connected device. 
   
To use one-touch audio, you must map the 
audio input from the connected device to 
your Home Theater System.
   
Audio Input Mapping 
   
When you map the audio input correctly, this 
Home Theater System switches to the audio 
from the played device automatically.
   
 
 
Get started
English
 
						

							24
   
For example, if the TV audio is 
connected to the  AUX1 
 jack on this 
Home Theater System, select  [Aux1] 
 
and map with the TV (brand name) at 
the right panel.
6  Select the audio input of this Home 
Theater System that is used to connect to 
other HDMI device (e.g. AUX1, AUX2), 
then press  
  . 
7  Select the correct connected device, then 
press  OK 
.
   
 
 
Repeat steps 5~7 to map other    »
connected devices.
8   Press     
 SETUP 
 to exit the menu.
   
 
 
 
 
 
 
Aux 2
Audio Input Mapping
Aux 1[TV]
other (Non-HDMI) [DVD 3400]Coaxial In
Optical In
Map the audio inputs to the 
connected devices
Note
  Before you star t, ensure that the audio output   •
of the HDMI T V and other HDMI devices have 
been connected to the audio input jacks on 
this Home Theater System. 
1 Press  DISC 
.
2 Press   
 
 SETUP 
.
   
 
 
    »[General Setup] 
 menu is displayed.
3 Press   
.
4 Select  [EasyLink Setup] 
, then press   
.
   
 
 
  • [One Touch Play] 
 and  [One Touch 
Standby] 
 functions are turned on by 
default in the factor y. 
5 Select  [System Audio Control] 
 >  [On] 
, 
then press  OK 
 to star t scanning devices.
   
 
 
Once complete, audio input mapping    »
menu is displayed.
OSD Language
Sleep Timer Screen Saver Disc Lock
Display Dim
General Setup
DivX(R) VOD CodeEasyLink
One Touch Standby
System Audio Control
Audio Input Mapping
One Touch Play
EasyLink Setup
EN
 
						

							25
On the remote control 
   
 
 
Press   • AUDIO SOURCE 
 repeatedly to 
switch to the connected audio source:
Display  Device connected to
 
 
AUX 1 
AUDIO IN-AUX1 jacks
   
AUX 2 
AUDIO IN-AUX2 jacks
   
COA X IN 
COA XIAL DIGITAL IN jack
   
OPTI IN 
OPTICAL DIGITAL IN jack
   
MP3 LINK 
MP3 LINK jack
   
 
 
Press   • RADIO 
 to switch to FM band.
   
 
 
Press   • USB 
 to switch to USB mode.
   
 
 
Press   • DISC 
 to switch to disc mode.
Select a play source
 
 
 
On the main unit 
   
 
 
Press   • SOURCE 
 button repeatedly to 
select:  DISC 
 >  USB 
 
 >   
FM >   
AUX 1 > 
   
 
 
AUX 2 >   
 
 
COA X IN >   
OPTI IN 
 > 
  MP3 LINK 
 >  DISC 
 ...
   
 
 
 
EN
Get started
English
 
						

							26
Play video
Note
  For video disc, playback always resumes from   •
the point where it was last stopped. To star t 
play from the beginning, press  
   while the 
message is displayed.
Control video play
1  Play a title.
2  Use the remote control to control the 
title. 
Button  Action
 
  
Star ts, pauses or resumes disc 
play.
   
 
Stops disc play.
   
 
Skips to the nex t title or chapter.
   
 
Skips to the beginning of the 
current title or chapter. Press 
twice to jump to the previous 
title or chapter.
   
 
 /   
Searches fast-for ward (right) 
or fast-back ward (lef t). Press 
repeatedly to change the search 
speed.
   
In pause mode, slow motion 
back ward or for ward play.
   
 
 /   
Searches slow-for ward (down) 
or slow-back ward (up). Press 
repeatedly to change the search 
speed.
   
For VCD, only slow-for ward play 
is possible.
   
 
 
 
5 Play
Play a disc
Caution
 
Never place any objects other than discs into   •
the disc compar tment.
   
Never touch the disc optical lens inside the 
  •
disc compar tment.
1 Press   
 to open the disc compar tment.
2  Inser t a disc with its label facing up.
   
 
 
For double-sided disc, load the side  • 
to play faces up.
3 Press     to close the disc compar tment 
and star t disc play.
   
 
 
To view disc play, turn on the T V to  • 
the correct viewing channel for this 
Home Theater System.
   
 
 
To stop disc play, press   • 
 
.
Note
 
Check the types of discs suppor ted. (see   •
‘Speci cations’ > ‘Playback media’).
   
If the password entr y menu is displayed, enter 
  •
the password before you can play the locked 
or restricted disc.
   
If you pause or stop a disc for about 5 minutes, 
  •
the screen saver activates. To deactivate the 
screen saver, press  DISC 
.
   
Af ter you pause or stop a disc and no but tons 
  •
are pressed within 15 minutes, this Home 
Theater System automatically switches to 
standby mode. 
EN
 
						

							27
Access DVD menu
1 Press  DISC 
 to access disc main menu.
2  Select a play option, then press  OK 
.
   
 
 
In some menus, press the   • Numeric 
buttons 
 to input your selection.
   
 
 
To return to the title menu during  • 
play, press  
   
 BACK 
.
   
 
 
 
 
 
 
 
Change video play
1  Play a title.
2  Use the remote control to change the 
video play. 
Button  Action
 
 
AUDIO 
SYNC  Selects an audio language or 
channel on a disc.
   
SUBTITLE 
Selects the subtitle language on 
a disc.
   
REPEAT 
Selects or turns off repeat or 
shuf e mode. 
   
Repeat options var y depending 
on the disc type. 
   
For VCDs, repeat play is only 
possible if the PBC mode is 
turned off.
   
ZOOM 
Zooms in or out of the picture.
   
To pan through the zoomed 
image, press the  Navigation 
buttons 
.
   
 
 
 INFO 
Displays the current status or 
disc information.
   
You can change the video 
play options here without 
interrupting disc play.
Note
  Some operations may not work with some   •
discs. See the information accompanying the 
disc for details.
Play
English
EN
 
						

							28
Sync audio output with video play
   
If the video play is slower than the audio 
output (sound does not match with the 
pictures), you can delay the audio output to 
match the video.
1  Press and hold  AUDIO SYNC 
 until 
‘AUDIO SYNC’ is displayed.
2  Within  ve seconds, press  VOL +/- 
 to set 
the delay time for audio output.
Note
  If the volume control is not used within  ve   •
seconds, it resumes normal volume control 
function. 
Quick skip play to a specifi c time
1  During play, press     
 INFO 
.
   
 
 
The disc status menu is displayed.   »
2 Press   
  
 to view information, then press 
  OK 
.
   
 
 
  • [TT Time] 
 (title time) 
   
 
 
  • [Ch Time] 
 (chapter time) 
   
 
 
  • [Disc Time] 
 (disc time) 
   
 
 
  • [Track Time] 
 (track time) 
3  Press the  Numeric buttons 
 to enter the 
time where you want to skip to, then 
press  OK 
.
Note
 
The options are different depending on the   •
disc type.
Access VCD menu or preview menu
 
 
The PBC (Playback Control) for VCD is 
activated by default in the factor y. When you 
load in a VCD, the contents menu is displayed. 
1 Press      
 to select a play option, then 
press  OK 
 to star t play.
   
 
 
If PBC is off, it skips the menu and  • 
star ts play from the  rst title.
   
 
 
To return to the menu during play,  • 
press  
   
 BACK 
 (only possible if the 
PBC mode is on).
2 Press  DISC 
 to preview the contents of 
the disc.
   
 
 
To exit the menu, press   • DISC 
.
3  Select a preview play option, then press 
  OK 
   
 
[Track Digest] 
   
Plays the  rst few seconds of each track in a 
disc.
   
 
[Disc Interval] 
   
Divides the total disc time by six and play the 
 rst few seconds of these inter vals.
   
 
[Track Interval] 
   
Divides the current track by six and play the 
 rst few seconds of these inter vals. 
   
This option is not available in stop mode.
Tip
 
You can change the PBC set ting (see ‘Adjust   •
set tings’ > ‘Preferences’ >  [PBC] 
).
Select Digest Type:
Track Digest
Disc Interval
Track Interval 
EN
 
						

							29
Play DivX® video
   
DivX video is a digital media format that 
retains high quality despite a high rate of 
compression. You can enjoy DivX video on 
this DivX® Cer ti ed Home Theater System.
1  Inser t a disc or USB that contains the 
DivX videos.
2 Press  DISC 
 or  USB 
.
   
 
 
A contents menu is displayed.   »
3  Select a title to play, then press   
.
4  Use the remote control to control the 
title. 
Button  Action
 
 
AUDIO 
SYNC  Selects an audio language or 
channel.
   
SUBTITLE 
Select DVD or DivX subtitle 
languages.
   
 
Stops play.
   
For DivX Ultra video, press 
this button again to display the 
contents menu.
   
 
 
 INFO 
Displays DivX Ultra video 
information.
Note
  You can only play DivX videos that were   •
rented or purchased with the DivX 
registration code of this Home Theater System 
(see ‘Adjust set tings’ > ‘General setup’ > 
  [DivX(R) VOD Code] 
) .
   
You can play DivX video  les of up to 4GB .
  •
 
 
If the subtitle does not appear correctly,   •
change the character set (see ‘Adjust set tings’ 
> ‘Preferences’ >  [DivX Subtitle] 
).
   
This Home Theater System can display up to 
  •
45 characters in the subtitle.
 
 
 
 
 
 
Repeat play a specifi c section
1  During playback, press   
 
 INFO 
.
   
 
 
The disc status menu is displayed.   »
2 Select  [Repeat] 
 in the menu, then press  
 
.
3  Move to  [ A-B] 
 in the menu, then 
press  OK 
 to set the star ting point.
4 Press  OK 
 again to set the ending point.
   
 
 
Repeat play star ts.   »
5  To cancel repeat play, select  [Of f ] 
 and 
press  OK 
.
Note
 
The marked section for repeat play is only   •
possible within a track /title.
View video play from different camera 
angles
1  During play, press     
 INFO 
.
   
 
 
The disc status menu is displayed.   »
2 Select  [Angle] 
, then press   
.
3  Press the  Numeric buttons 
 to select an 
angle, then press  OK 
.
   
 
 
Play changes to the selected angle.   »
Note
 
Applicable only to discs contain multi-angle   •
scenes.
 
 
 
 
 
EN
Play
English
 
						

							30
Play MP3/WMA music
   
MP3/ WMA is a type of highly compressed 
audio  le ( les with .mp3 or .wma extensions).
1  Inser t a disc or USB that contains the 
MP3/WMA music.
2 Press  DISC 
 or  USB 
.
   
 
 
A contents menu is displayed.   »
3  Select a folder, then press  OK 
.
4  Select a track to play, then press   
.
   
 
 
To return to the main menu, press   • 
 
 
 BACK 
 or press   
 until ‘Previous’ 
folder is selected, then press  OK 
.
Note
 
For disc recorded in multiple sessions, only the   •
 rst session is played.
   
This Home Theater System does not suppor t 
  •
MP3PRO audio format.
   
If any special characters are present in the MP3 
  •
track name (ID3) or album name, it might not 
be displayed correctly on the screen because 
these characters are not suppor ted. 
   
Some WMA  les are protected by Digital 
  •
Rights Management and cannot be played on 
this Home Theater System.
   
Folders/ les that exceed the suppor ted limit 
  •
of this Home Theater System will not be 
displayed or played.
Tip
  You can select the display of data contents,   •
view folders or  les (see ‘Adjust set tings’ > 
‘Preferences’ >  [MP3/JPEG Display] 
).
Play music
Control audio track play
1  Play a track.
2  Use the remote control to control the 
track. 
Button   Action
 
  
Star ts, pauses or resumes 
disc play.
   
 
Stops disc play.
   
 
Skips to the nex t track.
   
 
Skips to the beginning of 
the current track. Press 
twice to jump to the 
previous track.
  Selects an item to play.
   
 
 /   
Searches fast-forward 
(right) or fast-back ward 
(lef t). Press repeatedly to 
change the search speed.
   
REPEAT 
Selects or turns off repeat 
or shuf e mode.
   
 
 
 
EN