Philips Bdl3221vs User Manual

Regulatory Information
marked with the letter E or by the Earth symbol 
 or coloured GREEN or GREEN AND 
YELLOW. 
2. The BLUE wire must be connected to the 
terminal which is marked with the letter N or 
coloured BLACK. 
3. The BROWN wire must be connected to the 
terminal which marked with the letter L or 
coloured RED. 
Before replacing the plug cover, make certain 
that the cord grip is clamped over the sheath of 
the lead - not simply over the three wires. 
 
RETURN TO TOP OF THE PAGE 
Waste...

Other Related Information
Other Related Information
Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information 
for Users in the U. S. • Information for Users Outside the U.S 
Information for Users in the U. S.
For units set at 115 V : 
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT\
 three conductor cord 
a maximum of 15-feet long and a parallel blade, grounding type attachmen\
t plug rated 15 A, 125 V. 
For units set at 230 V: 
Use a UL Listed...

Philips Pixel Defect Policy
 
Philips Pixel Defect Policy
Product Features • Technical Specifications • Resolution and Preset Modes • Automatic 
Power Saving • Physical Specification • Pin Assignment • Product Views
Philips LCD Panel Pixel Defect Policy
Philips strives to deliver the highest quality products. We use some of \
the industrys most advanced 
manufacturing processes and practise stringent quality control. However,\
 pixel or sub pixel defects 
on the TFT LCD panels used in flat panel...

Philips Pixel Defect Policy
 
Types of Pixel Defects 
Pixel and sub pixel defects appear on the screen in different ways. Ther\
e are two categories of pixel 
defects and several types of sub pixel defects within each category. 
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit o\
r on. That 
is, a bright dot is a sub-pixel that stands out on the screen when the monitor displays \
a dark pattern. 
There are the types of bright dot defects:
One lit red, green or...

Philips Pixel Defect Policy
One dark sub pixelTwo or three adjacent dark sub pixels
Proximity of Pixel Defects 
Because pixel and sub pixels defects of the same type that are near to o\
ne another may be more 
noticeable, Philips also specifies tolerances for the proximity of pixel\
 defects. 
 
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects durin\
g the warranty period, a TFT 
LCD panel in a Philips flat panel monitor must have pixel or sub pixel d\
efects...

Philips Pixel Defect Policy
Tiny bright dots less then 50% R/B, 30% GMax 4
* Bright Dot is defined as dots (sub-pixels) which appeared brightly i\
n the screen when the LCM 
displayed with whole pattern & Bright Dots brightess is defined over 50\
% of the brightness against 
around. (but, Green bright dot is over 30% of brightness against around\
)
* Here in Tiny Bright Dot is defined as for Red and Blue the bright ar\
ea should be no longer than 
1/2 sub-pixel and for green the bright area should be no...

 
 
 
 
 
 
 
SERIAL INTERFACE 
COMUNICATION PROTOCOL 
& 
RC CONTROL 
 
 
 
 
 
 
2838   100   05424
 
 
 
[ NAME ] 
                      Philips 
 01 14023
 

 
 
Contents 
1. Introduction........................................................................\
...................................................4 
1.1 Purpose........................................................................\
.................................................4 
1.2 Scope........................................................................\
....................................................4 
1.3 Definitions, Abbreviations and...

 
3.3.3.6 PIP VIDEO SOURCE........................................................................\
..............21 
3.3.3.7 CHANNEL SELECTION........................................................................\
..........22 
3.3.4 Audio Group........................................................................\
................................22 
3.3.4.1 SMART SOUND........................................................................\
......................22 
3.3.4.2...

 
1. Introduction 
1.1 Purpose 
This document describes how to operate the BDS Monitor Series, using the IR remote 
control unit (using standard Philips RC5 code) and the RS-232 Serial Communication 
Interface. This document defines all the command and messages exchanged \
between 
the master and the slave monitors for BDS. It also describes the ways to send or read 
the commands or the messages. 
1.2 Scope 
This document is the reference for design, implementation and testing the RC and 
RS232...