Philips Bdl3221vs User Manual
Here you can view all the pages of manual Philips Bdl3221vs User Manual. The Philips manuals for Television are available online for free. You can easily download all the documents as PDF.
Page 71
![Page 71
2. Enabling The IR Remote Control
2.1 Monitor Address
To allow individual control, a 3-digit address (decimal format) is ass\
igned to each
monitor that can be modified by the user.
The default address set in the factory is 000.
2.2 Enabling and disabling the IR remote control(Reserved)
If the remote controller is disabled by the SICP command in section 3.3.2.9, the remote
controller doesn’t work since the monitor is powered on. It is possible to enable or
disable the remote control device on...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-70.png "Page 71
2. Enabling The IR Remote Control
2.1 Monitor Address
To allow individual control, a 3-digit address (decimal format) is ass\
igned to each
monitor that can be modified by the user.
The default address set in the factory is 000.
2.2 Enabling and disabling the IR remote control(Reserved)
If the remote controller is disabled by the SICP command in section 3.3.2.9, the remote
controller doesn’t work since the monitor is powered on. It is possible to enable or
disable the remote control device on...")
2. Enabling The IR Remote Control 2.1 Monitor Address To allow individual control, a 3-digit address (decimal format) is ass\ igned to each monitor that can be modified by the user. The default address set in the factory is 000. 2.2 Enabling and disabling the IR remote control(Reserved) If the remote controller is disabled by the SICP command in section 3.3.2.9, the remote controller doesn’t work since the monitor is powered on. It is possible to enable or disable the remote control device on...
Page 72
![Page 72
Fig. 1 Remote controllers for BDS PAL and NTSC model on the left and right, res\
pectively.
2838 100 05424
[ NAME ]
Philips
06 14023](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-71.png "Page 72
Fig. 1 Remote controllers for BDS PAL and NTSC model on the left and right, res\
pectively.
2838 100 05424
[ NAME ]
Philips
06 14023")
Fig. 1 Remote controllers for BDS PAL and NTSC model on the left and right, res\
pectively.
2838 100 05424
[ NAME ]
Philips
06 14023
Page 73
![Page 73
3. Serial Interface Communication Protocol
3.1 General specifications
3.1.1 Protocol definition
Communication to the main monitor microprocessor is possible through the\
serial port,
which support a communication protocol dedicated to BDS only. The protocol is \
specifically designed to allow data communication in half duplex multi-point
environments, but it can also be used for half duplex point-to-point RS-232
communication.
3.1.2 Communication characteristics
A half duplex communication...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-72.png "Page 73
3. Serial Interface Communication Protocol
3.1 General specifications
3.1.1 Protocol definition
Communication to the main monitor microprocessor is possible through the\
serial port,
which support a communication protocol dedicated to BDS only. The protocol is \
specifically designed to allow data communication in half duplex multi-point
environments, but it can also be used for half duplex point-to-point RS-232
communication.
3.1.2 Communication characteristics
A half duplex communication...")
3. Serial Interface Communication Protocol 3.1 General specifications 3.1.1 Protocol definition Communication to the main monitor microprocessor is possible through the\ serial port, which support a communication protocol dedicated to BDS only. The protocol is \ specifically designed to allow data communication in half duplex multi-point environments, but it can also be used for half duplex point-to-point RS-232 communication. 3.1.2 Communication characteristics A half duplex communication...
Page 74
![Page 74
3.2 Data frame
3.2.1 Poll sequence: frame format
The poll sequence must be transmitted before sending any command, to che\
ck whether
the monitor is ready to accept a command or it is busy.
The poll message in enclosed in a frame that has the following format:
where:
= , i.e. ASCII characters [1Bh] and [24h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are
used as monitor address.
= the ASCII character [45h].
= , i.e. the ASCII character [3Bh]....](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-73.png "Page 74
3.2 Data frame
3.2.1 Poll sequence: frame format
The poll sequence must be transmitted before sending any command, to che\
ck whether
the monitor is ready to accept a command or it is busy.
The poll message in enclosed in a frame that has the following format:
where:
= , i.e. ASCII characters [1Bh] and [24h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are
used as monitor address.
= the ASCII character [45h].
= , i.e. the ASCII character [3Bh]....")
3.2 Data frame
3.2.1 Poll sequence: frame format
The poll sequence must be transmitted before sending any command, to che\
ck whether
the monitor is ready to accept a command or it is busy.
The poll message in enclosed in a frame that has the following format:
where:
= , i.e. ASCII characters [1Bh] and [24h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are
used as monitor address.
= the ASCII character [45h].
= , i.e. the ASCII character [3Bh]....
Page 75
![Page 75
Note: While Standby bit is set, the SICP engine accepts only STANDBY com\
mand in
miscellaneous group is accepted.
3.2.3 General sequence: frame format
A message can be sent to the monitor to execute a command or to ask for \
any
information; each message is enclosed in a frame, which consists of the \
following:
...
where:
= , i.e. ASCII characters [1Bh] and [24h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are \
used as monitor address....](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-74.png "Page 75
Note: While Standby bit is set, the SICP engine accepts only STANDBY com\
mand in
miscellaneous group is accepted.
3.2.3 General sequence: frame format
A message can be sent to the monitor to execute a command or to ask for \
any
information; each message is enclosed in a frame, which consists of the \
following:
...
where:
= , i.e. ASCII characters [1Bh] and [24h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are \
used as monitor address....")
Note: While Standby bit is set, the SICP engine accepts only STANDBY com\
mand in
miscellaneous group is accepted.
3.2.3 General sequence: frame format
A message can be sent to the monitor to execute a command or to ask for \
any
information; each message is enclosed in a frame, which consists of the \
following:
...
where:
= , i.e. ASCII characters [1Bh] and [24h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are \
used as monitor address....
Page 76
![Page 76
... \
where:
= The ASCII character [06h], to tell the transmitter that the command has
been acknowledged.
= The ASCII characters [15h], to tell the transmitter that the command
has not been acknowledged, because the command itself is not valid
for any reason.
= , i.e. ASCII characters [1Bh] and [25h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are
used as monitor address.
= An ASCII character which identifies the command type, i.e. the...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-75.png "Page 76
... \
where:
= The ASCII character [06h], to tell the transmitter that the command has
been acknowledged.
= The ASCII characters [15h], to tell the transmitter that the command
has not been acknowledged, because the command itself is not valid
for any reason.
= , i.e. ASCII characters [1Bh] and [25h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are
used as monitor address.
= An ASCII character which identifies the command type, i.e. the...")
... \
where:
= The ASCII character [06h], to tell the transmitter that the command has
been acknowledged.
= The ASCII characters [15h], to tell the transmitter that the command
has not been acknowledged, because the command itself is not valid
for any reason.
= , i.e. ASCII characters [1Bh] and [25h].
= 3 ASCII characters each of which ranging from [30h] to [39h], which are
used as monitor address.
= An ASCII character which identifies the command type, i.e. the...
Page 77
![Page 77
COMPOSITE
S VIDEO
EXT •
3.3.1 Geometry Group
3.3.1.1 VIDEO MODE
Command: VM
Function: Set the format of the screen output for video inputs.
Data Range:
[00h] – WIDE SCREEN(STANDARD MODE)
[01h] – 4:3
[02h] – ZOOM 16:9 (FULL SCREEN)
[03h] – SUPER WIDE (NONLINEAR SCALING)
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP • • • •
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.1.2 PIP SIZE
Command: PS
Function:...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-76.png "Page 77
COMPOSITE
S VIDEO
EXT •
3.3.1 Geometry Group
3.3.1.1 VIDEO MODE
Command: VM
Function: Set the format of the screen output for video inputs.
Data Range:
[00h] – WIDE SCREEN(STANDARD MODE)
[01h] – 4:3
[02h] – ZOOM 16:9 (FULL SCREEN)
[03h] – SUPER WIDE (NONLINEAR SCALING)
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP • • • •
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.1.2 PIP SIZE
Command: PS
Function:...")
COMPOSITE
S VIDEO
EXT •
3.3.1 Geometry Group
3.3.1.1 VIDEO MODE
Command: VM
Function: Set the format of the screen output for video inputs.
Data Range:
[00h] – WIDE SCREEN(STANDARD MODE)
[01h] – 4:3
[02h] – ZOOM 16:9 (FULL SCREEN)
[03h] – SUPER WIDE (NONLINEAR SCALING)
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP • • • •
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.1.2 PIP SIZE
Command: PS
Function:...
Page 78
![Page 78
S VIDEO
EXT
3.3.1.3 PIP POSITION
Command: PP
Function: Control the PIP position.
Data Range:
[00h] – Upper left corner
[01h] – Upper right corner
[02h] – Bottom right corner
[03h] – Bottom left corner
This command is only supported in PC Analog/Digital inputs and when the
PIP is not OFF.
Model
Source PAL NTSC AP CHINA
PC ANALOG • • • •
PC DIGITAL
(DVI) • • • •
HDCP
COMPOSITE
S VIDEO
EXT
3.3.1.4 ZOOM Type
Command: ZT...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-77.png "Page 78
S VIDEO
EXT
3.3.1.3 PIP POSITION
Command: PP
Function: Control the PIP position.
Data Range:
[00h] – Upper left corner
[01h] – Upper right corner
[02h] – Bottom right corner
[03h] – Bottom left corner
This command is only supported in PC Analog/Digital inputs and when the
PIP is not OFF.
Model
Source PAL NTSC AP CHINA
PC ANALOG • • • •
PC DIGITAL
(DVI) • • • •
HDCP
COMPOSITE
S VIDEO
EXT
3.3.1.4 ZOOM Type
Command: ZT...")
S VIDEO
EXT
3.3.1.3 PIP POSITION
Command: PP
Function: Control the PIP position.
Data Range:
[00h] – Upper left corner
[01h] – Upper right corner
[02h] – Bottom right corner
[03h] – Bottom left corner
This command is only supported in PC Analog/Digital inputs and when the
PIP is not OFF.
Model
Source PAL NTSC AP CHINA
PC ANALOG • • • •
PC DIGITAL
(DVI) • • • •
HDCP
COMPOSITE
S VIDEO
EXT
3.3.1.4 ZOOM Type
Command: ZT...
Page 79
![Page 79
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.1.5 ZOOM ID
Command: ZD
Function: Select Zoom ID .
Data Range: It depend on zoom type.
[00h] : [00h] ----- Zoom type 1x1(Zoom off)
[00h] : [0Fh] ----- Zoom type 4x4
[00h] : [08h] ----- Zoom type 3x3
[00h] : [03h] ----- Zoom type 2x2
[00h] : [04h] ----- Zoom type 1x5
0
•0 •1 •2 •3
•4 •5 •6 •7
•8 •9 •A •B
•C •D •E •F
•0 •1 •2
•3 •4 •5
•6 •7 •8
•0 •1
•2 •3
•0 •1 •2...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-78.png "Page 79
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.1.5 ZOOM ID
Command: ZD
Function: Select Zoom ID .
Data Range: It depend on zoom type.
[00h] : [00h] ----- Zoom type 1x1(Zoom off)
[00h] : [0Fh] ----- Zoom type 4x4
[00h] : [08h] ----- Zoom type 3x3
[00h] : [03h] ----- Zoom type 2x2
[00h] : [04h] ----- Zoom type 1x5
0
•0 •1 •2 •3
•4 •5 •6 •7
•8 •9 •A •B
•C •D •E •F
•0 •1 •2
•3 •4 •5
•6 •7 •8
•0 •1
•2 •3
•0 •1 •2...")
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.1.5 ZOOM ID
Command: ZD
Function: Select Zoom ID .
Data Range: It depend on zoom type.
[00h] : [00h] ----- Zoom type 1x1(Zoom off)
[00h] : [0Fh] ----- Zoom type 4x4
[00h] : [08h] ----- Zoom type 3x3
[00h] : [03h] ----- Zoom type 2x2
[00h] : [04h] ----- Zoom type 1x5
0
•0 •1 •2 •3
•4 •5 •6 •7
•8 •9 •A •B
•C •D •E •F
•0 •1 •2
•3 •4 •5
•6 •7 •8
•0 •1
•2 •3
•0 •1 •2...
Page 80
![Page 80
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP
COMPOSITE
S VIDEO
EXT
3.3.2.2 STANDBY
Command: SB
Function: Standby ON/OFF.
Data Range:
[00h] – Standby OFF
[01h] – Standby ON
“Standby ON” means the set enters standby mode.
Query is not supported in this command.
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP • • • •
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.2.3 LIGHT...](http://img.usermanuals.tech/thumb/59/54394/w300_philips_bdl3221vs-user-manual-79.png "Page 80
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP
COMPOSITE
S VIDEO
EXT
3.3.2.2 STANDBY
Command: SB
Function: Standby ON/OFF.
Data Range:
[00h] – Standby OFF
[01h] – Standby ON
“Standby ON” means the set enters standby mode.
Query is not supported in this command.
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP • • • •
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.2.3 LIGHT...")
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP
COMPOSITE
S VIDEO
EXT
3.3.2.2 STANDBY
Command: SB
Function: Standby ON/OFF.
Data Range:
[00h] – Standby OFF
[01h] – Standby ON
“Standby ON” means the set enters standby mode.
Query is not supported in this command.
Model
Source PAL NTSC AP CHINA
PC ANALOG
PC DIGITAL
(DVI)
HDCP • • • •
COMPOSITE • • • •
S VIDEO • • • •
EXT • • • •
3.3.2.3 LIGHT...