Philips 46pfl9715k User Manual

5.83D
3D
This   TV   is  prepared   for   the   3D   Full  HD   accessory  PTA02  (sold
separately).
PTA02   Installation
1 Switch   off   the   TV.
2  Connect  the   3D   transmitter   to  the   3D   connection   3D   Out  on
the   back   of   the   TV.
3  Install   the   3D   transmitter   on   the   top   or  at  the   bottom  of   the
TV.   Make   sure  to  point   the   transmitter   directly   to  where   you   sit
to  watch   TV.
The  small   window   in   the   middle  of   the   glasses...

6
6.1
Troubleshooting
Contact information
If   the   advice   and  suggestions  in   Troubleshooting   do   not   help
resolve   the   problem,  try   switching   the   TV   off   and  back   on   again.
Warning
If   your   TV   breaks  down, NEVER  try   to  repair   the   TV   yourself.
Consumer  Care
If   the   TV   problem  is  not   solved   you   can   call  the   Philips
Consumer   Care   hotline   in   your   country.   Look  up  the   TV   model
and  serial  number  before   you   call.  Find...

6.2TV and remote control
The   TV  does   not   switch   on
•   Switch   the   TV   off   and  on   again  with   the   switch   on   the   bottom
of   the   TV.
•   Check   the   power   cable   connection.
•   Try  using  the   keys   on   the   TV   to  switch   on.
The   TV  does   not   switch   on   from  standby
•   Check   that  the   batteries   of   the   remote   control   are   not   empty
or  weak.  Check   their   +  /   -  orientation.
•   Try  using  the   keys   on   the   TV   to...

6.3TV channels
Some   TV  channels   are  gone
•   Check   if  the   correct   list   is  selected  in   the   Channel   list.  Press
¬FIND   to  open   the   Channel   list,  then  press   rOPTIONS  and
select  the   list   you   need  with   Select  list.
•   A   channel  could   be  hidden   in   the   Channel   list.  Read  more
about   Channel   list   in   Help > Use   your  TV  > Watch  TV >
Channel  list .
No  digital   channel  found  during  installation
•   Check   if  the   TV   supports...

6.4Picture and sound
No  picture
•   Check   if  the   antenna  is  connected   properly.
•   Check   if  the   correct   device   is  selected  and  connected   properly.
•   Check   the   contrast   or  brightness   setting  in   h > Setup  > TV
settings  > Picture  > Contrast   or Brightness .
The   picture  is   poor
•   Bad   weather  can   influence   the   picture   quality.
•   Check   if  the   antenna  is  connected   properly.
•   Non -earthed   audio   devices,   neon   lights,   high...

6.5Devices
HDMI  connections
•   The  HDMI -HDCP  procedure  might  take  a  few  seconds   before
the   picture   from  a  device   appears.
•   If   the   TV   does  not   recognise   the   device   and  there  is  no
picture,   try   switching   from  one  device   to  another  and  back   again
to  restart  the   HDCP  procedure.   Or   switch   the   device   off   and
back   on   again.
•   If   sound   interruptions   occur  persistently,   see  the   user  manual   of
the   device   to  check...

6.6Videos, photos and music
The   files  on   my  USB  device   are  not   shown
•   Set   your   device   (camera)  to  ‘Mass  Storage  Class’  compliant.
•   The  USB   device   may   need  specific   driver   software.
Unfortunately,   this   software   cannot   be  downloaded   to  your   TV.
•   Not   all   audio   and  picture   files   are   supported.  See  the   list   in
Help > Specifications  > Multimedia.
Files  from  a  USB  device   do  not   play   back  smoothly
•   The  transfer...

6.7Network
Wireless   network   not   found  or   distorted
•   Microwave  ovens,   Dect   phones  or  other   WiFi  11b  devices  in
your   neighbourhood   might  disturb   the   wireless  network.
•   Make   sure  that  the   firewalls  in   your   network   allow   access   to
the   TV   wireless  connection.
•   If   the   wireless  network   does  not   work   properly  in   your   home,
try   the   wired  network   installation.   Read  Help > Setup  >
Network  > Wired  installation.
Net   TV  does...

7
7.1
Specifications
Software
Software version
To   view   the   current  TV   software   version,  press  h > Setup  >
Software   settings   and  press  OK.  Select   Current  software  info
and  read  Version:.
Open source software
This   television  contains  open   source   software.  Philips  hereby
offers  to  deliver,   upon   request,   a  copy  of   the   complete
corresponding   source   code   for   the   copyrighted   open   source
software   packages   used   in   this   product  for   which...

7.2Environmental
Energy saving
Light  sensor
To   save   energy,   the   built -in   ambient   light   sensor  lowers   the
brightness   of   the   TV   screen  when   the   surrounding  light   darkens.
Energy  saving
The  energy  saving  Smart  picture   setting,   combines  several   TV
settings   that  result   in   saving  energy.
Low  standby  power
The  class-leading   and  highly  advanced   power   circuitry  brings  down
the   power   consumption  of   the   TV   to  an   extremely   low...