Panasonic Wv Sw355 Installation Guide

21
z Loosen two fixing screws on both ends of the base cover by using the bit for tamperproof screw (accessory), and remove the base cover (accessory).
  Install the mount bracket (accessory) on the wall/ceiling.
  (For use of the hole A)

 




51 mm {2"}
ø27 mm 
{1-1/16"}
135 mm {5-5/16"} 135 mm 
{5-5/16"}
For use of the hole 
85 mm {3-11/32"}
85 mm 
{3-11/32"}
For use of the hole 
Cable access hole Mount bracket (accessory)
Center of mount bracket
Female thread for...

22
Note:
  • Only the same type of holes, (A) or (B),  shall be used for mounting.
x  Pass the cables through the hole for cable running from the wall or ceiling. 
c  Fix the camera attachment on the mount bracket using the screws supplied with the bracket. 
    Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Note:
  •  For wall mounting:
    The camera attachment shall be mounted with "gTOP" facing upward. (Except the case of  connecting the conduit upward (
☞ page 20))
  •  For ceiling...

23
Important:
  •  Before inserting the SDHC/SD memory card, turn off the power of the camera first.
  •  When inserting an SDHC/SD memory card, make sure the direction.
  •  Before removing the SDHC/SD memory card, select "Not use" for "SD memory card" on the  [SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then unload the SDHC/SD memory card. When the SDHC/SD memory card is inserted or 
removed with the power on, data in the...

24
Heater Unit WV-SW3H (option)
  • Installing this heater unit enables the camera to operate in a low-tempe\
rature environment below –30 °C {22 °F}. A small fan inside the unit will minimize\
 condensation on the surface of 
the enclosure caused by changes in ambient temperature unless temperatures change too rap-
idly. The fan will stop when there is no possibility of condensation.
  •  The heater unit is automatically turned on or off according to the temperature inside the camera  that is monitored....

25
 e  Attach the enclosure to the camera. (☞ Page 40)
Heater unit 
(option) connectorScrew (accessory of 
the heater unit)* 
* Two screws are supplied with the heater unit.  (Of them, 1 for spare) 

26
Caution:
  •  FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY. 
Turn off a circuit breaker before making a connection. Before starting the connection, prepare the 
required devices and cables. Note:
  •  When using the mount bracket (accessory), it is possible to connect th\
e cables after mounting  the camera onto the mount bracket. 
  •  Refer to page 20 when connecting the conduit.
Connection
Network cable
* PAL model only * PAL model only
RJ-45 (female)
Alarm input/output cable...

27
x  Connect an external amplifier-embedded speaker to the audio output cable (for use of the 
audio transmission function).
    Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). 
  •  Recommended cable length: Less than 10 m {32.8 ft}
c  Connect the alarm input/output cable.
  
Terminal name Ratings
ALARM OUT, AUX OUT Open collector output (maximum applied voltage: 20 V DC) Open: 4 V DC - 5 V DC by internal pull-up
Close Output voltage 1 V DC or less (50 mA or less)
ALARM IN, DAY/NIGHT...

28
v  Connect a LAN cable (category 5e or better, straight, STP*) to the network connector.
    * PAL model only 
b  Connect the power cable. 
  •  When using 12 V DC power supply*
1
    Connect the output cable of the AC adaptor to the 2P power cable.
  •  When using PoE (IEEE802.3af compliant)
    Connect a LAN cable (category 5 or better, straight, STP*
2) between a PoE device (such as a 
hub) and the network connector of the camera. 
  *1  FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER...

29
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be sure to use the supplied butyl rubber tape at the points where the cables are connected to 
apply waterproof treatment in the following procedure. Failure to observe this or use of a tape other 
than the provided butyl rubber tape (such as a...

30
Connection example when connecting to a network using a 
PoE hub

LAN cable (category 5 or better, straight, STP*)
* PAL model onlyImportant: 
  •  The video monitor is used for checking the adjustment of the angular fie\
ld of view when install- ing the camera or when servicing. It is not provided for recording/monitoring use.
  •  Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
  •  Power supply is required for each network camera. When using a PoE device (hub), 12 V DC...