Panasonic Wv Sw355 Installation Guide

11
Precautions
Refer installation work to the dealer.
Installation work requires technique and experi-
ences. Failure to observe this may cause fire, 
electric shock, injury, or damage to this prod-
uct. 
Be sure to consult the dealer. 
Stop the operation immediately when 
something is wrong with this product. 
When smoke goes up from the product, the 
smell of smoke comes from the product, or the 
exterior of the product has deteriorated, contin-
ued use will cause a fire or fall of the product...

12
Do not rub the edges of metal parts with 
your hand. 
Failure to observe this may cause injury. 
Do not touch this product, the power cord 
or the connected cables during thunder. 
(even in the process of work)
Failure to observe this may cause electric 
shock.
Turn the power off when cleaning this 
product. 
Failure to observe this may cause injury. 
[Precautions for use]
This product has no power switch. 
When turning off the power, turn off a circuit 
breaker. 
To keep on using with stable...

13
  •  When some SDHC/SD memory cards are used with this product, the product may 
not work properly or performance deterio-
ration may be caused. Use the SDHC/SD 
memory cards recommended in page 47. 
Code label
The code labels (accessory) are required at 
inquiry for trouble. Use caution not to lose 
these labels. It is recommended to paste one 
of the labels onto the CD-ROM case.
Discoloration on the color filter of the 
MOS image sensor
  •  When continuously shooting a bright light  source such as...

14
Precautions for installation
This product is designed to be installed 
under eaves.
Install the product under eaves to avoid direct 
sunlight.
Installing place
Contact your dealer for assistance if you are 
unsure of an appropriate place in your particu-
lar environment.
  • Make sure that the installation area is strong enough to hold this product, such 
as a concrete ceiling. 
  •  Install the camera in the foundation area of  the architecture or where sufficient strength 
is assured.
  •  If a...

15
Do not remove or loosen the screws on 
the rear of this product. 
If the screws (7 pcs.) are loosened, water expo-
sure may cause damage or malfunction of the 
product, or dropping may result in injury.
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a 
motor, a transformer or a power line), images 
may be distorted and noise sound may be pro-
duced. 
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with 
IEEE802.3af...

16
Major operating controls
Enclosure
Inner dome
MONITOROUT
HEATER
SD CARD / AF
AF/EXTRAOPTICAL ZOOM
INITIAL
SET
TOPTilting table Zoom lock knob
Zoom ring
Focus ring
Tilting lock screw (x2)
Azimuth 
adjustment ring
Audio output cable (black) Network cable
* PAL model only RJ-45 (female)
Alarm input/output cable
Power cable (12 V DC)
Microphone/line input cable (white)
FRONTTOP
Mount bracket (accessory)
Base cover
(accessory)
Camera attachment (accessory) 

17
About the initial set button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing the button. Wait around 2 minutes 
after releasing the button. The camera will start up and the settings including\
 the network settings 
will be initialized. Before initializing the settings, it is recommended to write down the settings in 
advance. Do not turn off the power of the camera during the process of...

18
When installing the camera on a wall or a ceiling, there are two methods as specified below.
  •  Using a two-gang junction box
  •  Use the supplied mount bracketImportant:
  •  Procure 4 screws (M4) to secure the camera attachment (accessory) or the mount bracket  (accessory) to a wall or a ceiling according to the material of the installation area. Do not use 
wood screws and nails.
    For mounting a camera on a concrete ceiling, use an anchor bolt (for M4) or an AY plug bolt  (M4) for securing....

19
Using a two-gang junction box
  •  Secure the camera attachment (accessory) to the two-gang junction box built\
 in a wall or ceil-ing.
Note:
  •  For wall mounting:
    The camera attachment shall be mounted with "gTOP" facing upward. 
  •  For ceiling mounting:
    The camera attachment shall be mounted with " hFRONT" facing in the direction of the camera 
front (model number indication face).
Using the mount bracket (accessory)
Note:
  •  When the camera is mounted on the wall or...

20
Important:
  •  If open wiring is conducted, be sure to use conduits and run the cables inside the tubes to pro- tect the cables from direct sunlight.
  •  When connecting the conduit at the lateral or bottom position, any of th\
e arrow marks on the  bracket shall be at the top.
  •  When connecting the conduit upward, mount the camera attachment with the arrow position  on either left or right side. 
    
    
  •  For installation on the wall, do not connect the conduit at the upper si\
de to...