Panasonic Wv Sw355 Installation Guide

31
z  Mount the camera.
    
  q  Connect each cable. (
☞ Page 26) Waterproof the connecting portion. (☞ Page 29)
  w  Align the "OPEN" on the camera with the projection of the camera attachment.
  e  Engage the camera attachment fixing screws on the rear of the camera in the camera 
mounting holes of the camera attachment and rotate the camera in the arrow direction to 
secure the camera attachment and camera. 
    Rotate the camera until a click is heard so that the projection of the camera...

32

 q  Attach the camera onto the camera attachment 
while aligning the "OPEN" mark of the camera 
with the projection of the camera attachment. 
LOCKOPEN
Projection
LOCK
OPEN
Important: 
  •  When mounting the camera body, cables shall  be run between the camera attachment and 
mount bracket as indicated by the arrows in the 
illustration.
  *  Cable running as indicated by the arrows in the  illustration is an example. Cable running shall be 
varied with installation environment. 
    

33
 w  Engage the rear-side screw of the camera with 
the screw hole of the camera attachment and 
rotate the camera in the direction of the arrow 
to secure the camera to the camera attach-
ment.
    Rotate the camera until a click is heard so that  the projection of the camera attachment will be 
set to the "LOCK" position.
  e  Connect the cables on the side of the mount 
bracket. (
☞ Page 26)
   Waterproof the connecting portion. (
☞ Page 
29)
Note:
  • Disconnect the 12 V power source and...

34
 t Attach the base cover that was removed 
according the steps in page 21.
  y  Use the bit for tamperproof screw (accessory) 
to tighten the fixing screws provided on both 
sides of the base cover. (Recommended tight-
ening torque: 0.78 N·m {0.58 lbf·ft})
x  Detach the enclosure and inner dome from the 
main body by loosening the three fixing screws. 
    Loosen the three fixing screws by using the bit  for tamperproof screw (accessory). 
   Detach the inner dome while pushing toward  the directions...

35
c  Secure the camera to the mount bracket with 
the camera fixing screw (red, 1 position).
   The illustration is an example of using the  mount bracket (accessory). 
Important: 
  • Be sure to tighten the camera fixing screw.  Failure to observe this may cause camera trou-
ble due to water leakage or camera falling. 
   (Recommended tightening torque: 0.78 N·m  {0.58 lbf·ft})
Camera fixing screw (red)
* The camera fixing screw  shall be securely tightened. 

36
z  Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning 
table, tilting table, and azimuth adjustment ring. 
Horizontal position (Panning)
Loosen the panning lock screw, rotate the panning table to adjust the pan direction. (Adjustable 
range: 340 °)
Panning is possible within the range of 180 ° (when panning clockwis\
e) and 160 ° (when panning 
counterclockwise). 
After adjustment, tighten the panning lock screw to fix the panning table....

37
    Horizontal: 27.7 ° (TELE) to 100.8 ° (WIDE)
Vertical: 20.8 ° (TELE) to 73.8 ° (WIDE)
    After adjustment, tighten the tilting lock screws (x2) to fix the tilting table. 
    (Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Note:
  •  When the tilting table is turned to the edge of the adjustable range (±75°), it must be noted\
 that  the shadow of the enclosure may be projected.
Image tilt adjustment
Rotate the azimuth adjustment ring to adjust the azimuth angle of the im\
age. (Adjustable...

38
x  Adjust the angular field of view and the focus. 
    Adjust the angular field of view in accordance with the distance between the camera lens and a  photographic subject. These adjustments shall be performed together with\
 the camera angle 
adjustment.
  q  Loosen the zoom lock knob and move the knob between TELE and WIDE to obt\
ain the appro-
priate angle of view. 
Note:
  •  The focus may not be adjusted appropriately when the zoom ring is positioned at the "W" (or  "T") end. In...

39
Important: 
  •  Do not move the focus ring.
  •  Defocus may be caused by the reinstalled enclosure. In this case, perform the auto focus func- tion from the setup menu. 
Note:
  •  If the zoom ring is fully rotated in the "W" direction, the periphery may become dark. In such a  case, rotate the zoom ring in the "T" direction for readjustment. 
  •  If the zoom lock knob is slightly tightened before the zoom ring is moved, the ring will become  stable to ease the fine adjustment. 
  •...

40
c  Mount the inner dome that was removed according the steps in page 34 in the reverse proce-dure. Check to see that the tilting lock screws of the camera are properly engaged in the holes 
of the inner dome.
    Tighten the screws that have been loosened in step  x on page 34 using the bit for tamper-
proof screw (accessory). 
Important: 
  •  Securely tighten all the fixing screws (x3) of enclosure. Otherwise, water exposure may cause  damage or malfunction of camera, or camera dropping may result...