Panasonic Wv Sc385 Installation Guide

Place the camera upside-down on a desktop without fixing
Use it as a simple desktop device at meetings and on other occasions.
Place the camera on a level place not subject to vibrations.
Ensure that the camera does not fall.
When using the camera upside-down, select "On (desktop)" for "Upside-d\
own" on the [Cam. Function] tab of the setup 
menu. (☞ Operating Instructions (PDF))
Pass the power cord from a 12 V DC power supply (accessory) through the cable guides after connecting the...

Connection example
When connecting with a PC directly

LAN cable (category 5 or better, cross, STP*)
* PAL model only
When connecting to a network using a PoE hub

LAN cable (category 5 or better, straight, STP*)
* PAL model onlyImportant:
  •  The video monitor is used for checking the adjustment of the angular fie\
ld of view when installing the camera or when  servicing. It is not provided for recording/monitoring use. 
  •  Depending on the monitor, some characters (camera title, preset ID, etc.) may...

Step 4
Rotate the camera counterclockwise to detach the cam-
era from the camera mount bracket (accessory). 
Important:
  •  When detaching the camera from the camera mount  bracket, hold the base of the camera. Detaching the 
camera while holding the moving part may result in 
malfunction. 
 
Step 5
Detach the cables from the camera. 
Step 6
Detach the safety wire from the camera. 
Detach the camera
The camera is fixed on the camera mount bracket using the fixing screw. Remove the camera by following...

Insert/remove an SDHC/SD memory card
How to insert an SDHC/SD memory card
Important:
  •  Before inserting the SDHC/SD memory card, turn off the power of the camera first. 
  •  When inserting an SDHC/SD memory card, make sure the direction. 
  •  When the SDHC/SD memory card is inserted or removed with the power on, data in the SDHC/SD memory card may  be damaged. 
Step 1
Push the left corner of the Panasonic logo plate on the 
front panel to unlock the SDHC/SD memory card slot 
cover.
Step 2
Slide the...

How to remove the SDHC/SD memory card
Important:
  •  Before removing the SDHC/SD memory card, select "Not use" for "SD memory card" on the [SD memory card] tab of  "Basic" on the setup menu first. (☞ Operating Instructions (PDF))
Step 1
Open the SDHC/SD memory card slot cover by following 
steps 1 and 2 of the "How to insert an SDHC/SD memory 
card" section. 
Step 2
Push the SDHC/SD memory card until a click is heard and 
then pull the SDHC/SD memory card from the slot....

Configure the network settings
Install the software
Before installing the software, refer to the readme file on the provided CD-ROM first. 
Software included on the provided CD-ROM
  •  Panasonic IP setting software
    Configure the network settings of the camera. Refer to the following for further\
 information. 
  •  Viewer Software "Network Camera View 4S"
    It is necessary to install the viewer software "Network Camera View 4S" to display images on a PC. Install the viewer software...

Step 1
Start the Panasonic IP setting software. 
Step 2
Click the [Network Settings] button after selecting the 
MAC address/IP address of the camera to be configured.
Note:
  •  When using a DHCP server, the IP address assigned  to the camera can be displayed by clicking the 
[Search] button of the IP setting software. 
  •  When a duplicate IP address is used, the correspond- ing camera number will be displayed shaded.
  •  When the [Access Camera] button is clicked, live  images of the selected camera...

Troubleshooting
Before asking for repairs, check the symptoms with the following table. 
Contact your dealer if a problem cannot be solved even after checking and trying the solution in th\
e table or a problem is 
not described below. 
SymptomCause/solutionReference 
pages
Power is not turned on.  When using DC power supply
 •  Is the 12 V DC power cord plug (accessory) firmly inserted into the 
12 V DC power terminals of the camera?
    Confirm the power plug is firmly connected. 
When using a PoE...

SymptomCause/solutionReference 
pages
Live indicator keeps on 
blinking orange approx. in 2 
seconds intervals.  •  UPnP
TM error has occurred since the power is not supplied to the 
router. 
    Turn on the power of the router. Wait until the connections are  established.  −
 •  An error has occurred during the port update by the UPnP
TM func-
tion. 
 •  If the router in use does not support the UPnP
TM function, perform 
the port forwarding setting for the router. In addition, deactivate the 
setting...

About the live indicator
The live indicator will light or blink as follows depending on the camer\
a status. 
Operation statusIndicator status
When the power is turned on Before the network  connection is establishedBlinks orange
When the network 
connection is established Blinks orange → Blinks green → Lights green
During the standby or connection (Cable is not connected.) Lights orange
During the standby or connection (Cable is connected.) Lights green
During the upgrade process Blinks orange
During...