Panasonic Wv Sc385 Installation Guide

AVC Patent Portfolio License
This product is licensed under the AVC Patent Portfolio 
License for the personal and noncommercial use of a con-
sumer to (i) encode video in compliance with the AVC 
Standard ("AVC Video") and/or (ii) decode AVC Video that 
was encoded by a consumer engaged in a personal and 
non-commercial activity and/or was obtained from a video 
provider licensed to provide AVC Video. No license is 
granted or shall be implied for any other use. Additional 
information may be...

Precautions for installation
No responsibility will be taken by our company with 
respect to consequeces resulting from the use, 
damage or both of the camera.
Installing place
Contact your dealer for assistance if you are unsure of an 
appropriate place in your particular environment.
  •  Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
  •  When the installation area is not strong enough, rein- force and strengthen it or use an optional mount...

Major operating controls
Front view
   
FRONT
OPENLOCK
Camera mount bracket (accessory)
LOCK
WV-SC385
OPEN
Safety wire
(fixed with the mount bracket)
CameraDecorative cover (accessory)
WV-SC385WV-SC385
SDHC/SD memory card slotSDHC/SD memory card slot cover
Panasonic logo plate
Transparent part (over the lens)
13 

Rear view
MONITOR OUTAUDIO OUT
MIC/LINE INEXT I/O
4  3  2  112V   IN
POWER
INITIAL
SET
ACT
LINK
10BASE-T/
100BASE-TX
Safety wire holder Monitor out connector 
for adjustment
Audio output connector
Microphone/line input connecto
r
External I/O terminals
12 V DC power supply terminal INITIAL SET button
Cable guide
Network connector Link indicator 
(lighting at linking)
Access indicator 
(blinking at accessing)
About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of...

Installations/Connections
The following are descriptions of how to install the camera. The camera can be installed\
 on a ceiling. The camera can also 
be installed upside down on the bracket or can be placed upside down on \
a desktop.
Before starting the installation/connection, prepare the required devices and cables.
Before starting the connection, turn off the power of the devices including the camera and the PC or disconnect\
 from the 
12 V DC power supply.
Install on ceiling
When installing the...

Wire through a hole in the ceiling
   
Step 1
Fix the camera mount bracket (accessory) with four 
optional fixing screws (M4 or M6, option).
There should be no obstacles such as wall in a range of 
100 mm {3-15/16"} away from the center point of the 
camera mount bracket.
Step 2
Make a hole in the ceiling to pass the cables through.
Make a hole 25 mm {31/32"} in diameter. The center point 
of the hole should be located approx. 75 mm {2-15/16"} 
away from the center point of the camera mount...

Specification of cable (wire): AWG #22 - #28, Single core, twisted
Important:
  •  Do not connect 2 wires or more directly to a terminal.  When it is necessary to connect 2 or more wires, use 
a splitter.
  •  Input and output of the external I/O terminal 2 and 3  can be switched by configuring the setting. The 
default of EXT I/O terminal 2 is "ALARM IN 2" and of 
EXT I/O terminal 3 is "ALARM IN 3". It is possible to 
determine whether or not to receive input from EXT 
I/O terminal 2 and...

Important:
  •  When mounting the camera onto the camera mount  bracket, hold the base part of the camera. Mounting 
the camera while holding the moving part may result 
in malfunction.
 
Step 7
Fix the camera on the camera mount bracket (accessory) 
using the camera fixing screw (accessory).
Recommended tightening torque: 0.68 N·m  {0.50 lbf·ft}
   
Step 8
Connect the cables to the network connector and the 
power inlet.
Important:
  •  When the power of the camera is turned on, the cam- era will start...

• 12 V DC power supply terminal
 q  Loosen the screw of the power cord plug (accessory).
  w  Connect the cable of the 12 V DC power supply* to 
the power cord plug. 
    Strip 3 mm to 7 mm {1/8" to 9/32"} from the end of  the wire, and twist the stripped part of the wire suffi-
ciently to avoid short circuit. 
Specification of cable (wire): 16 AWG - 24 AWG, Single core, twisted
  •  Check whether the stripped part of the wire is not  exposed and is securely connected.
  e  Tighten the screw of...

Wire without making a hole in the ceiling
Step 1
Install the camera by following step 1 and steps 3 - 8 of the 
"Wire through a hole in the ceiling" section (☞ pages 16 - 18). It 
is unnecessary to make a hole in the ceiling as described in step 
2 of the "Wire through a hole in the ceiling" section.
Step 2
Remove the tab on the rear of the decorative cover (accessory) 
that is blocking the wiring hole.
Attach the decorative cover by following step 9 of the "Wire 
through a hole in...