Panasonic Wv Nw484s Operating Instructions Manual

31
Alarm In/Out Ratings
..............................................................................................................................Note
 Check the Operating Instructions (provided) to see if the ratings of sensors and other 
external devices are compatible with the camera ratings.
...................................................................................................................................
Pin Arrangement of 4-pin Alarm Cable (accessory)Terminal Name Rating...

32
Handling SD Memory Cards 
Insertion and Removal of SD Memory Cards
To insert or remove an SD memory card, the dome cover must be removed. 
(→page 21)
Important
 Before inserting an SD memory card, turn the camera off.
o
1Insert the SD memory card into the 
SD memory card slot.
2Press the SD memory card in as far 
as possible until it is fixed in place. 
Your will hear it click into place.
3To remove an SD memory card, press 
it in as far as possible again. You will 
hear it click and it will rise up....

33
Heater Unit 
When the heater unit (sold separately) is used, the camera can be used outdoors in low-
temperature environments down to -30ºC (-22ºF). The heater automatically turns on when 
the temperature inside the camera falls below about 10ºC (50ºF), and turns off when the 
temperature inside rises. The condensation fan alleviates the problem of clouding 
(condensation) caused by temperature change in the camera dome caused. Note, however, 
that significant condensation caused by sudden temperature...

34
Connection Examples 
Direct connection to a PC
When connecting the camera 
directly to a PC, use the Ethernet 
cable (Category 5, cross cable).
Network connection via a PoE-compatible hub
When connecting the camera to a network via a PoE-compatible hub, use the Ethernet 
cable (Category 5, straight cable).
Important
 The monitor is intended solely for checking the view angle during installation or 
servicing. It is not intended for recording or monitoring images.
 Text displayed on the monitor...

35
Network Setup 
Installing the Software
Be sure to read the Readme file in the CD-ROM (provided) before installing the software. 
Software in CD-ROM
 Panasonic IP setup software
This software is used to make network settings on the camera. For details, refer to the 
following.
Network Camera View3
To display images on this camera, the viewer software Network Camera View3 must be 
installed. This software can be installed directly from the camera or by double clicking 
nwcv3setup.exe on the CD-ROM...

Network Setup (continued)
36
1Launch the IP setup software.
2Click the MAC address/IP address of 
the camera to set up, and click the [IP 
setting] button.
..................................................Note
 When a DHCP server is in use, 
you can check the IP address 
assigned to the camera by clicking 
the [Refresh] button in the IP 
setup software.
......................................................
3Enter each of the network items, and 
click the [Apply] button....

37
Monitor Images on a PC 
The following describes how to monitor images from the camera on a PC.
The following shows the functions of the buttons on the Live page.
 (1/3)
No. Item Description
(1) [Camera title] The camera title entered for Camera title on the 
[Basic] tab in the Setup menu is displayed. (→Setup 
Manual)
(2) [Setup] button
*1Click this button to display the setup menu.
(3) [Live] button Click this button to display the Live page.
(4) [Multi-screen] buttons Images from multiple cameras...

Monitor Images on a PC (continued)
38
(6) [Image capture size] Click these buttons to set the resolution of the main 
area to VGA or QVGA. 
These buttons will be displayed only when JPEG is 
selected as the image type.
[VGA] button Click this button to display images in the main area at 
VGA size.
[QVGA] button Click this button to display images in the main area at 
QVGA size.
(7) [ZOOM] Click the desire button to enlarge the displayed image.
Only the image in the main area is enlarged.
[X1] button...

39
(12) [One shot] button Click this button to take a picture (a still picture) and 
display it in a newly opened window.
To save the image to PC, right-click on the displayed 
image and select Save.
(13) Main area Images from the camera are displayed in this area. 
The current date and time are displayed at the selected 
position using the date and time format set in the setup 
menu. (→Setup Manual)
*1 Only operable by users whose access level is 1. Administrator
*2 Only operable by users whose access...

Monitor Images on a PC (continued)
40
Monitor images from a single camera
 Web browser screen
Live page
1Launch the web browser on the PC.
2Enter the IP address designated using the 
Panasonic IP setup software (→page 35) in 
the address box of the browser. 
(Example: http://192.168.0.10)
3Press the [Enter] key. 
When ON is selected for User Authentica-
tion, the window for entering the user name 
and password is displayed.
2
4Display images from the camera.