Panasonic Wv Nw484s Operating Instructions Manual

11
MPEG-4 Visual patent portfolio license
This product is licensed under the MPEG-4 
Visual patent portfolio license for the 
personal and non-commercial use of a 
consumer for (i) encoding video in 
compliance with the MPEG-4 Visual 
Standard (MPEG-4 Video) and/or (ii) 
decoding MPEG-4 Video that was encoded 
by a consumer engaged in a personal and 
non-commercial activity and/or was 
obtained from a video provider licensed by 
MPEG LA to provide MPEG-4 Video. No 
license is granted or shall be implied...

Precaution (continued)
12
Do not point the camera at a strong light 
source.
 Intense light such as that produced by a 
spotlight concentrated on one part of 
the screen can cause blooming 
(rainbow around the strong light) or 
smearing (vertical stripes above and 
below the strong light).
Consumables
The item listed below is a consumable. 
Replace it using the service life values as 
guides. Note that actual service life is 
affected by the operating environment and 
conditions.
Cooling fan: Approx....

13
Names of Components
(1) Enclosure
(2) Mounting bracket (accessory)
(3) Network cable (6) Tilting lock screw (9) Focus lever
(5) Power cable (4) Alarm I/O cable (11) Zoom lever
(7)Tilt adjustment
seat
(10) Panning lock screw (8) Panning table
(19) Monitor output jack
(20) SD memory card slot(14) ABF button (ABF)(13) INIT button (INIT)(15) LED ON/OFF switch button
(16) Access LED (ACT) (12) Heater Unit connector
(17) Link LED (LINK)
(18) ABF LED (ABF)
(21) SD memory card error LED 

Names of Components (continued)
14
(1) Enclosure
(2) Mounting bracket (accessory)
(3) Network cable
(4) Alarm I/O cable
(5) Power cable
(6) Tilting lock screw
Fixes the tilt position after adjusting.
(7) Tilt adjustment seat
Adjusts the screen tilt.
(8) Panning table
Adjusts the horizontal angle of the 
camera.
(9) Focus lever
Fixes the focus position.
(10) Panning lock screw
Fixes the panning position after 
adjusting.
(11) Zoom lever
Fixes the zoom position after adjusting.
(12) Heater output...

15
Functions 
When there is wide variation between the illumination of light and dark areas of the location 
being monitored, the camera adjusts the lens iris in accordance with the bright areas. This 
causes loss of detail in dark areas. Conversely, adjusting lens brightness for the dark areas 
causes brighter areas to become washed out.
SUPER-D 
III digitally combines an image that is set up for a clear view of bright areas with 
an image that is set up for a clear view of dark areas, creating a final...

Functions (continued)
16
Jagged edges that are unique to interlaced cameras and that occur in areas with movement 
are corrected by the motion adaptive interlace/progressive conversion function and 
converted to progressive images. This allows both still and moving objects to be captured as 
well-defined images.
The privacy zone function allows you to mask specific areas, such as housing, of a 
monitored scene from view.
Back focus can be automatically adjusted by operating the buttons on the camera,...

17
Power can be supplied to the camera and images transmitted on a single LAN cable by 
connecting to PoE-compatible network devices. Special installation of a power supply for the 
camera and video cables is not required.
MPEG-4 and JPEG can be output at the same time.
MPEG-4 operation when monitoring in real time or from a remote site, and JPEG operation 
when recording and verifying images at high quality can both be achieved at the same time 
in a network environment.
Special Power Supply and Cable...

18
Installation and Connections 
Installation Precautions
The following describes how to install the camera.
Before you install and connect the camera, check and prepare the required peripheral 
devices and cables.
Before you connect the camera, turn off all devices to be connected, such as this camera 
and PC.
Camera Installation Location
Discuss the installation location for the 
camera with your retailer, and select a 
place that is strong enough for the installa-
tion.
 Install the camera on a...

19
About Static Electricity Removal
Before installing the camera, touch a metal 
case or other metallic parts with your hand 
to remove static electricity from your body.
Do not install in areas subjected to high 
amounts of humidity or dust.
Doing so may cause internal components 
to damage more easily or malfunction.
Do not wire cables near power lines.
Configure the power supply to the 
camera so that it can be turned on and 
off.
The camera does not have a power switch, 
so configure the power supply...

20
Before Starting Installation 
The following procedures are for installing the camera on walls and ceilings.
Important
 The type of screws for the installation depend on the material at the location in which 
you will install the bracket (included). However, do not use wood screws or nails. 
Metal material: Use M6 or M5 bolts and nuts for mounting. 
Concrete wall: Use M6 or M5 anchor bolts for mounting. 
 Be sure that the arrow on the installation bracket is pointing upwards.
 A pull-out force in...