Panasonic Wv Nw484s Operating Instructions Manual

21
Installing the Camera 
1Install the mounting bracket. 
Fix the mounting bracket directly into 
the ceiling or wall or into the 
imbedded box using the four screws 
prepared in advance. (Note that 
screws for installation are not 
provided.) 
When using the imbedded box, we 
recommend using two boxes in a row 
as shown in the figure below on the 
r ight. (This is to make it easier to pass 
the cables through.) 
..................................................Note
 When installing the camera...

Installing the Camera (continued)
22
3Unscrew the transportation screw. 
4Connect the power cable and the 
video output cable. 
See Waterproofing Cable Joints on 
page 26.
Transportation screw
Imbedded box for connecting 
cables Imbedded box for camera installation 

23
5Install the camera on the mounting 
bracket. 
Fix the camera onto the mounting 
bracket using the four screws 
(provided).
During installation, align the protrud-
ing part on the mounting bracket and 
the indented part on the camera to fix 
the position of the camera.
Make sure to tighten the screws used 
for mounting the camera.
(M4:0.78 N·m) {8kgf·cm}
You can keep the camera waterproof 
by firmly tightening the installation 
screws....

Installing the Camera (continued)
24
6Adjust the camera angle while 
monitoring the image on the 
adjustment monitor. 
See Adjusting the Camera on 
page 28.
7Install the enclosure. 
Tighten the screws unscrewed at step 
3 using the driver bit (provided). 
Align the ▲ mark on the side of the 
enclosure with the line on the side of 
the bracket. (recommended torque: 
0.78 N·m {8 kgf·cm})...

25
Connecting the Cables 
Power cable
24 V AC 12 V DC
Brown (Live)Live Plus
Blue (Neutral)Neutral Minus
Green/yellow (GND)Connect to ground. 
Network cable
Alarm I/O cable
Power cord 
(24 V AC/12 V DC)
Green/Yellow (GND) Blue (Neutral) Brown (Live)4P alarm cable
(included) RJ-45 female/female conversion connector (included) 

Connecting the Cables (continued)
26
Waterproofing Cable Joints
Waterproof the cable to install the camera using exposed wiring, or when installing the 
camera under eaves. Though the camera body is waterproof, the cable ends are not 
waterproofed.
Follow the procedure below to waterproof the power cables (including Alarm I/O cable) and 
LAN cable connections using butyl rubber tape (provided). If vinyl tape other than butyl 
rubber tape (provided) is used, water may seep in between the gaps and cause a...

27
Important
 When wiring the cable by exposed wiring, be 
sure to use a sleeve to prevent the cable 
from being exposed to the direct sunlight.
 Install the camera so that the cable is at the 
bottom side of the camera. Draw out the 
cable to the side of the mounting fixture, set it 
facing down, and then wire it facing up.
 When installing the camera on a wall, install 
it so that the water drain groove is facing 
down. 
Also, do not block the water drain groove. 
Blocking the water drain groove...

28
Adjusting the Camera
1Adjust the camera angle while 
monitoring the image on the 
adjustment monitor. 
Connect the adjustment monitor 
(small LCD monitor, etc.) to the 
monitor output terminal, and adjust 
the camera angle. 
Determine and set the camera angle 
while repeating the fine-adjustments 
in steps (1), (2) and (3) below. 
(1) Loosen the pan lock screw, and 
rotate the camera horizontally to 
adjust pan. 
(2) Loosen the 2 tilt lock screws, and 
rotate the camera vertically to 
adjust tilt....

29
2Adjust the focus. 
Adjust the focus at the same time as 
pan and tilt adjustment. 
Repeat steps (1) and (2) to adjust the 
focus.
(1) Loosen the zoom lock lever, move 
the lens to the appropriate view 
angle between TELE and WIDE, 
and tighten the lever.
(2) Loose the focus lock lever, rough-
adjust the focus, and tighten the 
lever.
..............................................................................................................................Note
 When either the zoom or focus is...

Adjusting the Camera (continued)
30
..............................................................................................................................Note
• How to Change the View Angle
To change the view angle, turn the zoom lock lever and focus lock lever to adjust the 
focus.
 How to Focus (capturing subjects with a self-closing lens)
When the focus has been adjusted with the iris closed (to capture a bright subject), the 
subject may be out-of-focus when the iris is opened. So, try to...